We propose a model for non-ideal monitoring of the state of a coupled quantum dot qubit by a quantum tunnelling device. The non-ideality is modelled using an equivalent measurement circuit. This allows realistically available measurement results to be related to the state of the quantum system (qubit). We present a quantum trajectory that describes the stochastic evolution of the qubit state conditioned by tunnelling events (i.e. current) through the device. We calculate and compare the noise power spectra of the current in an ideal and a non-ideal measurement. The results show that when the two qubit dots are strongly coupled the non-ideal measurement cannot detect the qubit state precisely. The limitation of the ideal model for describing a realistic system may be estimated from the noise spectra.
We propose a model for non-ideal monitoring of the state of a coupled quantum dot qubit by a quantum tunnelling device. The non-ideality is modelled using an equivalent measurement circuit. This allows realistically available measurement results to be related to the state of the quantum system (qubit). We present a quantum trajectory that describes the stochastic evolution of the qubit state conditioned by tunnelling events (i.e. current) through the device. We calculate and compare the noise power spectra of the current in an ideal and a non-ideal measurement. The results show that when the two qubit dots are strongly coupled the non-ideal measurement cannot detect the qubit state precisely. The limitation of the ideal model for describing a realistic system may be estimated from the noise spectra.
We present a model for detection of the states of a coupled quantum dots (qubit) by a quantum point contact. Most proposals for measurements of states of quantum systems are idealized. However in a real laboratory the measurements cannot be perfect due to practical devices and circuits. The models using ideal devices are not sufficient for describing the detection information of the states of the quantum systems. Our model therefore includes the extension to a non-ideal measurement device case using an equivalent circuit. We derive a quantum trajectory that describes the stochastic evolution of the state of the system of the qubit and the measuring device. We calculate the noise power spectrum of tunnelling events in an ideal and a non-ideal quantum point contact measurement respectively. We found that, for the strong coupling case it is difficult to obtain information of the quantum processes in the qubit by measurements using a non-ideal quantum point contact. The noise spectra can also be used to estimate the limits of applicability of the ideal model.
Full text: Recently, we presented a model for continuous DC-biased measurement of a coupled quantum dot (CQD) charge qubit by realistic measurement devices. Modelling realistic measurement devices as ideal detectors embedded in an equivalent measurement circuit (see figure), our aim was to describe the evolution of the qubit state conditioned on the macroscopic output of the external circuit, i.e. the measured current. We generalised a recently developed quantum trajectory theory for realistic photodetectors to treat solid-state detectors-primarily a single electron transistor (SET). This method yields stochastic equations whose (numerical) solutions are the 'realistic quantum trajectories' of the conditioned qubit state. Here we present numerical solutions and analysis for the SET equations. The solutions elucidate the regimes in which (Rabi) electron tunnelling between the CQDs can be detected in a realistic measurement. Further to this, the solutions reveal the conditions under which electron tunnelling events through the SET can be observed, which is related to the question of the nature of the back-action noise of the SET. Copyright (2005) Australian Institute of Physics.
We propose a quantum trajectory analysis of a scheme to measure the states of a coupled-dot device (qubit) where there is a fluctuating energy gap Δ between the two states. The system consists of the qubit and a readout dot coupled to source and drain leads. The tunnel rate through the detector is conditioned by the occupation number of the nearer quantum dot (target) of the qubit and therefore probes the states of the qubit. We derive a Lindblad-form master equation to calculate the unconditional evolution of the qubit and a conditional stochastic master equation calculating the conditional evolution for different tunneling rates. The results show the effects of various device parameters and provide the optimum selection and combination of the system structure.
We present a new model for the continuous measurement of a coupled quantum dot charge qubit. We model the effects of a realistic measurement, namely adding noise to, and filtering, the current through the detector. This is achieved by embedding the detector in an equivalent circuit for measurement. Our aim is to describe the evolution of the qubit state conditioned on the macroscopic output of the external circuit. We achieve this by generalizing a recently developed quantum trajectory theory for realistic photodetectors [P. Warszawski, H. M. Wiseman, and H. Mabuchi, Phys. Rev. A 65, 023802 (2002)] to treat solid-state detectors. This yields stochastic equations whose (numerical) solutions are the ``realistic quantum trajectories'' of the conditioned qubit state. We derive our general theory in the context of a low transparency quantum point contact. Areas of application for our theory and its relation to previous work are discussed.
To obtain information about a system of interest a measurement has to be made. In experiments that probe the quantum nature of our world, the system itself is, in general, necessarily affected by the act of measurement. If the system is weakly coupled to its bath and the dynamics are such that information concerning the system is spread throughout the many degrees of freedom of the bath, and the bath is being measured then a stochastic master equation for the conditioned state of the system can be found. This is termed a quantum trajectory equation. Realistic detectors are not perfect. Information is lost in the conversion to a signal that the observer can use. This loss may occur in the detector itself, in the circuit containing the detector (described by a response time and electronic noise) or at the circuit output (electronic output noise). In order to obtain a true quantum trajectory for the experiment, the observer must condition the state of the quantum system on results that are available in the laboratory rather than on the microscopic events considered previously in quantum trajectories. A method for treating this was first proposed by Warszawski, Wiseman and Mabuchi [Phys. Rev. A 65, 023802 (2002)], in which the quantum system is embedded within a supersystem that also contains the state of the detector. They applied their theory to photodetectors of various sorts. Warszawski has also done the preliminary work on applying this theory to detecting the state of a pair of quantum dots using a SET (single-electron transistor) [MSc. Thesis, Griffith University (2001)]. The resulting theory is termed 'realistic' quantum trajectory theory. In this thesis, the approach of Warszawski, et al.is applied to various solidstate readout devices. These include the SET, the QPC (quantum point contact), and the RF-QPC (radio-frequency QPC). Numerically obtained realistic quantum trajectories for the QPC agree with heuristic results. In particular, in certain limits, the realistic quantum trajectories can take on the appearance of ideal quantum trajectories. This thesis also resolves a problem in solid-state continuous quantum measurement theory by deriving a quantum trajectory model for a SET-monitored charge qubit, that guarantees physically meaningful qubit states. The particular limit necessary to achieve this is discussed, and the SET measurement quality is analysed using techniques borrowed from quantum optics. Conditions for which the SET can approach operation at the limit allowed by quantum mechanics are given. This is also done for the QPC, for which the results agree with previous work.
Performing a quantum measurement yields two different results: a classical outcome drawn from a probability distribution, according to Born's rule, and a quantum outcome corresponding to the post-measurement state. Quantum devices that provide both outcomes can be described through quantum instruments. In a realistic scenario, one can expect that the observer's obtained classical and quantum outcomes are non-ideal: this can be due to experimental limitations, but could also be explained by adversarial interference, that is, a second party that disturbs the device through a concealed measurement to obtain information. The second scenario can be interpreted through quantum compatibility, as it implies that both the observer's instrument and the adversary's measurement can be performed simultaneously. In this work, we show how the noise of the observer's device relates to the amount of information that the adversary can obtain. We study scenarios in which the adversary aims to acquire information on the same basis as the observer's measurement, or on a mutually unbiased basis with respect to the observer's basis. In both cases, we derive necessary and sufficient conditions for the compatibility of a single qubit non-ideal quantum instrument and a noisy meter, from which we obtain the maximum amount of information that the adversary can extract in terms of the noise parameters of the observer's instrument. Finally, we provide the device implementation from the adversary's point of view for the same basis scenario.