Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE

Effects of radio frequency radiation on the dc SQUID

R. H. Koch, Vittorio Foglietti, James R. Rozen, Kevin G. Stawiasz, M. B. Ketchen, Daniel K. Lathrop, Jian Sun, W. J. Gallagher

Published Jul 2, 1994• 1 citation
Publisher

Abstract

The effects of radio frequency radiation on the dc SQUID are examined. Simulations show how the shape of the SQUID transfer characteristic is distorted by radio frequency interference (RFI). How this affects three commonly used SQUID modulation methods is discussed, and the results explain why we experimentally observe the bias current reversing readout method to be the least susceptible to RFI. The commonly seen increase in the low frequency flux noise power spectrum of dc SQUIDs in unshielded environments is also explained.

DOI
10.1117/12.181000

Related papers

Effects of radio frequency radiation on the dc SQUID

R. H. Koch, Vittorio Foglietti, James R. Rozen +5 more

The effects of radio frequency radiation on the dc SQUID are examined. Simulations show how the shape of the SQUID transfer characteristic is distorted by radio frequency interference (RFI). How this affects three commonly used SQUID modulation methods is discussed, and the results explain why we experimentally observe the bias current reversing readout method to be the least susceptible to RFI. The commonly seen increase in the low frequency flux noise power spectrum of dc SQUIDs in unshielded environments is also explained.

Applied Physics Letters•Jul 4, 1994•44 citations

Radio frequency bias current scheme for dc superconducting quantum interference device

Y. Zhang, Dongfeng He, N. Wolters +7 more

We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•0 citations

Comparative study of bias-reversing schemes for low frequency noise reduction in dc SQUIDS

James M. Lockhart, David Hipkins, G.M. Gutt +2 more

We have investigated the effectiveness for low frequency noise reduction of three different schemes of periodic bias current reversal in dc SQUIDs operated in the flux-locked mode. The three techniques incorporate different frequency and phase relationships between the bias current waveform and the flux modulation waveform. We find that some SQUIDs show significant low frequency noise reduction under bias reversing, while other SQUID devices of the same design inherently achieve the lower level of low frequency noise and hence do not benefit from bias reversal.

Physica B Condensed Matter•Feb 1, 1994•1 citation

Weak Radio Frequency Signal Reception Sensitivity Based on DC Superconducting Quantum Interference Devices

Shanchi Wu, Chen Gong, Shangbin Li +2 more

Superconducting quantum interference devices (SQUIDs) are promising for detection of extremely weak power regimes for the Internet of Things and long-distance satellite networks. In low-frequency magnetic signal measurements, it has demonstrated superior performance over the traditional systems. We review the resistively and capacitively shunted junction model of dc SQUIDs and investigate its transfer function to magnetic flux signals while taking thermal fluctuation into account. We numerically evaluate the influence of bias current and bias flux signal to determine the operating parameters of the device. The performances related to SQUID ring inductance operating at 4.2 K and 77 K are demonstrated. Combined with common radio frequency front-end modules, including low-noise amplifier and low-pass filter, we evaluate the bit-error-rate performance of the system under different inductance values and inferred that the sensitivity of the system can reach −99 dBm at 100 MHz bandwidth.

IEEE Transactions on Applied Superconductivity•Apr 13, 2023•7 citations

Radio‐Frequency (rf) SQUID

Yi Zhang, Hui Dong, Hans‐Joachim Krause +2 more

To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.

Wiley eBooks•May 29, 2020•0 citations

Effects of alternating bias current on the low-frequency noise in dc SQUIDs

Shinya Kuriki, M. Matsuda, Atsushi Matachi

We have analyzed the characteristics of flux modulated voltages of a dc SQUID for both positive and negative bias currents. It is shown that the change in the modulated voltage caused by fluctuations of the junction critical currents is eliminated after subtraction between the modulated voltages for the two biased currents. In the flux feedback mode using an alternating bias current, a large reduction of 1/f noise is observed for dc SQUIDs made of NbN junctions with amorphous Si tunnel barriers.

Journal of Applied Physics•Jul 1, 1988•10 citations
The effects of radio frequency radiation on the dc SQUID are examined. Simulations show how the shape of the SQUID transfer characteristic is distorted by radio frequency interference (RFI). How this affects three commonly used SQUID modulation methods is discussed, and the results explain why we experimentally observe the bias current reversing readout method to be the least susceptible to RFI. The commonly seen increase in the low frequency flux noise power spectrum of dc SQUIDs in unshielded environments is also explained.
The effects of radio frequency radiation on the dc SQUID are examined. Simulations show how the shape of the SQUID transfer characteristic is distorted by radio frequency interference (RFI). How this affects three commonly used SQUID modulation methods is discussed, and the results explain why we experimentally observe the bias current reversing readout method to be the least susceptible to RFI. The commonly seen increase in the low frequency flux noise power spectrum of dc SQUIDs in unshielded environments is also explained.
We have developed a radio frequency bias current scheme with reversal frequency up to 50 MHz for dc superconducting quantum interference devices (SQUIDs). The SQUID and the readout electronics, were connected via a quarter wavelength (/spl lambda//4) transmission line. This transmission line not only transported the SQUID signal, but also served as the resonant matching circuit. For a dc SQUID of inductance 115 pH (loop size 75/spl times/75 /spl mu/m/sup 2/), we measured a flux noise of 33 /spl mu//spl phi//sub 0///spl radic/Hz at 77 K in the flux locked loop configuration. The corner frequency of 1/f noise was less than 0.5 Hz.
We have investigated the effectiveness for low frequency noise reduction of three different schemes of periodic bias current reversal in dc SQUIDs operated in the flux-locked mode. The three techniques incorporate different frequency and phase relationships between the bias current waveform and the flux modulation waveform. We find that some SQUIDs show significant low frequency noise reduction under bias reversing, while other SQUID devices of the same design inherently achieve the lower level of low frequency noise and hence do not benefit from bias reversal.
Superconducting quantum interference devices (SQUIDs) are promising for detection of extremely weak power regimes for the Internet of Things and long-distance satellite networks. In low-frequency magnetic signal measurements, it has demonstrated superior performance over the traditional systems. We review the resistively and capacitively shunted junction model of dc SQUIDs and investigate its transfer function to magnetic flux signals while taking thermal fluctuation into account. We numerically evaluate the influence of bias current and bias flux signal to determine the operating parameters of the device. The performances related to SQUID ring inductance operating at 4.2 K and 77 K are demonstrated. Combined with common radio frequency front-end modules, including low-noise amplifier and low-pass filter, we evaluate the bit-error-rate performance of the system under different inductance values and inferred that the sensitivity of the system can reach −99 dBm at 100 MHz bandwidth.
To read out radio frequency (rf) superconducting quantum interference device (SQUID) signals, an rf resonance tank circuit is usually needed. Similar to dc SQUID systems, an rf SQUID system also detects a flux signal that can change slowly over time. In fact, rf SQUID readout electronics exhibit potential advantages over dc SQUID electronics in the direct readout scheme. A merit of rf SQUID systems is the need for just one coaxial cable to connect the readout electronics to the two-terminal element. In a complete magnetometric SQUID system, an input coil connects to a receiver loop (flux antenna) to pick up the measured signals and couples it to the SQUID via a mutual inductance. This chapter discusses the main differences between rf SQUIDs and dc SQUIDs. The significant difference between rf and DC SQUIDs is the occurrence of higher harmonic components in the flux-to-voltage characteristics.