Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Journal of Vacuum Science & Technology B Microelectronics and Nanometer Structures Processing Measurement and Phenomena

Postfabrication resistance trimming of a superconducting tunnel junction using a focused ion beam

Z. H. Barber, Mark G. Blamire, Nick Dawes

Published Mar 1, 1995• 2 citations
Publisher

Abstract

A high current density NbN/MgO/Nb superconducting tunnel junction has been modified using a focused ion beam to trim the junction area following fabrication and measurement. After milling, the exposed edge of the junction was cleaned of resputtered material using a low current ion beam combined with gas assisted etching. Some remaining shorts across the barrier were then removed by anodization. The modified junction showed a resistance increase correlating exactly with the decrease in area and very little change in quality. This technique may be used on fully fabricated circuits to trim accurately the resistance of selected junctions in order to overcome variations in barrier conductance and junction area.

DOI
10.1116/1.588372

Related papers

NbN/MgO/NbN edge-geometry tunnel junctions

B. D. Hunt, Henry George LeDuc, S.R. Cypher +2 more

We report the fabrication and low-frequency testing of the first edge-geometry NbN/MgO/NbN superconducting tunnel junctions. The use of an edge geometry allows very small junction areas to be obtained, while the all-NbN electrodes permit operation at 8–10 K with a potential maximum operating frequency above 1 THz. Edge definition in the base NbN film was accomplished utilizing Ar ion milling with an Al2O3 milling mask, followed by a lower energy ion cleaning step. This process has produced all-refractory-material tunnel junctions with areas as small as 0.1 μm2, resistance-area products less than 21 Ω μm2, and subgap to normal state resistance ratios larger than 18.

Applied Physics Letters•Jul 3, 1989•21 citations

Transport properties of nanoscale Nb and NbN Josephson junctions fabricated by focused-ion-beam milling

Kazuaki Matsuba, 道生 渡部, Jaw-Shen Tsai

We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.

Journal of Applied Physics•Apr 1, 2008•2 citations

Fabrication of High-Quality Niobium Superconducting Tunnel Junctions

Qinyin Xu, Chunhai Cao, Mengyue Li +6 more

For high-quality superconducting tunnel junctions (STJs), it is necessary to reduce leakage current as much as possible. We describe the fabrication of niobium STJs using the selective niobium (Nb) etching process and various ways to minimize the leakage current. The experiment shows that the leakage current mainly comes from shorts in the tunnel barrier layer rather than those around the junction edges. Through systematic analysis of the thin film stress, surface morphology and modified junction structures, we fabricate high-quality Nb STJs with a gap voltage of 2.8 mV and a leakage current at 1 mV as low as 8.1% and 0.023% at 4.2 K and 0.3 K, respectively.

Chinese Physics Letters•Aug 1, 2011•3 citations

Ion implantation into Nb/Nb oxide/PbAuIn Josephson tunnel junctions

Stanley I. Raider, G. J. Clark

Boron ions have been implanted into complete planar and edge Nb/Nb oxide/PbAuIn Josephson tunnel junctions to directly trim the Josephson current I0. Implantation caused reproducible increases in I0 and in the junction subgap conductance and decreases in the junction energy gap voltage Vg. The variations in junction properties were monotonic with 11B implant dose. Trimming of I0 was optimized when the 11B ions were implanted with the depth distribution peaked near the tunnel barrier.

Applied Physics Letters•Oct 1, 1984•2 citations

Machine-aligned fabrication of submicron SIS tunnel junctions using a focused ion beam

Robert B. Bass, J.Z. Zhang, Arthur W. Lichtenberger

The objective of our research is to develop a machine-aligned technique for the definition and insulation of Nb/Al-AlO/sub x//Nb superconducting-insulating-superconducting (SIS) tunnel junctions with areas as small as 0.2 /spl mu/m/sup 2/. The fabrication of such ultrasmall area planar SIS junctions had previously only been achieved using electron beam lithography (JPL). Typical techniques for the fabrication of micron-scale SIS junctions involve a self-aligned resist lift-off process. The resist pattern is used to define both the junction counter-electrode and the insulation field that separates the wiring layer from the base electrode. The wiring layer contacts the junction counter-electrode through a via in the insulation field that is created during resist liftoff. In our process, the junction is defined and insulated in separate steps; a via through the insulation layer to the junction is aligned and defined using a gallium focused ion beam with nanometer spot-size. Such small area SIS junctions have potential applications in high frequency SIS mixer circuits. They may also be used in experiments to investigate quantum coherence in superconducting circuits and may even serve as the key elements in future superconducting quantum computers.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•6 citations

Fabrication of Magnetic Barrier NbN Tunnel Junctions with the Gap Voltage over 5 mV

Ryo Terajima, Joe Sakai, Akira Kawakami +1 more

Superconductor–insulator–superconductor (SIS) tunnel junctions including magnetic barriers, with structures NbN/AlNiN/NbN or NbN/MgO/NiO/MgO/NbN, were fabricated. The junctions with upper NbN layers of good crystallinity showed a gap voltage ( V g ) higher than 5 mV. In an NbN/Al 0.942 Ni 0.058 N/NbN junction, its Josephson current I c was suppressed to approximately a third of a theoretical value under no magnetic field. Therefore, it would be possible to avoid Josephson noise in magnetic barrier junctions with a much smaller magnetic field than junctions with conventional barriers. The Ni ion area density dependence of I c suppression ratio was identical for both types of junction, suggesting that the area density of magnetic ions is the factor that determines the I c suppression ratio. On the other hand, the extents of degradation of V g and increase in leakage current caused by the increase in Ni ion area density were smaller in MgO/NiO/MgO barrier junctions than in AlNiN barrier junctions. This suggests that the proximity effect of magnetic ions was weakened owing to the separation of Ni ions and NbN layers by the inserted thin MgO layers.

Japanese Journal of Applied Physics•Mar 1, 2008•0 citations
A high current density NbN/MgO/Nb superconducting tunnel junction has been modified using a focused ion beam to trim the junction area following fabrication and measurement. After milling, the exposed edge of the junction was cleaned of resputtered material using a low current ion beam combined with gas assisted etching. Some remaining shorts across the barrier were then removed by anodization. The modified junction showed a resistance increase correlating exactly with the decrease in area and very little change in quality. This technique may be used on fully fabricated circuits to trim accurately the resistance of selected junctions in order to overcome variations in barrier conductance and junction area.
We report the fabrication and low-frequency testing of the first edge-geometry NbN/MgO/NbN superconducting tunnel junctions. The use of an edge geometry allows very small junction areas to be obtained, while the all-NbN electrodes permit operation at 8–10 K with a potential maximum operating frequency above 1 THz. Edge definition in the base NbN film was accomplished utilizing Ar ion milling with an Al2O3 milling mask, followed by a lower energy ion cleaning step. This process has produced all-refractory-material tunnel junctions with areas as small as 0.1 μm2, resistance-area products less than 21 Ω μm2, and subgap to normal state resistance ratios larger than 18.
We have studied low-temperature electrical transport properties of nanoscale Nb∕(Al–)Al2O3∕Nb and NbN∕AlN∕NbN Josephson junctions (JJs) fabricated by focused-ion-beam (FIB) milling. This FIB fabrication process yields high-quality JJs whose superconducting gap energy agrees with the bulk value. In this paper, we report the improvement in the precision of the fabrication technology by employing a weaker ion beam current and by introducing a step of XeF2-gas-assisted milling, which allowed us to reduce the anodization voltage. For Nb JJs, we measured the current-voltage (I-V) characteristics of single-electron transistors (SETs) and examined the current observed within the superconducting energy gap. At finite voltages, we observed current peaks due to the Josephson-quasiparticle (JQP) cycle. Based on the JQP-peak positions, we estimated the charging energy Ec of the SETs. For all SETs, Ec∕kB is larger than 1K, which is consistent with 0.1×0.1μm2 junctions. We also analyzed the superconducting critical current at zero voltage. The ratio Ic∕Ic0 depended on the junction size, where Ic is the measured critical current and Ic0 is the theoretical one. The I-V curves of NbN single Josephson junctions also depended on the junction size, and they were qualitatively different, especially around the energy gap. We will discuss the possible origins for the junction-size dependence.
For high-quality superconducting tunnel junctions (STJs), it is necessary to reduce leakage current as much as possible. We describe the fabrication of niobium STJs using the selective niobium (Nb) etching process and various ways to minimize the leakage current. The experiment shows that the leakage current mainly comes from shorts in the tunnel barrier layer rather than those around the junction edges. Through systematic analysis of the thin film stress, surface morphology and modified junction structures, we fabricate high-quality Nb STJs with a gap voltage of 2.8 mV and a leakage current at 1 mV as low as 8.1% and 0.023% at 4.2 K and 0.3 K, respectively.
The objective of our research is to develop a machine-aligned technique for the definition and insulation of Nb/Al-AlO/sub x//Nb superconducting-insulating-superconducting (SIS) tunnel junctions with areas as small as 0.2 /spl mu/m/sup 2/. The fabrication of such ultrasmall area planar SIS junctions had previously only been achieved using electron beam lithography (JPL). Typical techniques for the fabrication of micron-scale SIS junctions involve a self-aligned resist lift-off process. The resist pattern is used to define both the junction counter-electrode and the insulation field that separates the wiring layer from the base electrode. The wiring layer contacts the junction counter-electrode through a via in the insulation field that is created during resist liftoff. In our process, the junction is defined and insulated in separate steps; a via through the insulation layer to the junction is aligned and defined using a gallium focused ion beam with nanometer spot-size. Such small area SIS junctions have potential applications in high frequency SIS mixer circuits. They may also be used in experiments to investigate quantum coherence in superconducting circuits and may even serve as the key elements in future superconducting quantum computers.
Superconductor–insulator–superconductor (SIS) tunnel junctions including magnetic barriers, with structures NbN/AlNiN/NbN or NbN/MgO/NiO/MgO/NbN, were fabricated. The junctions with upper NbN layers of good crystallinity showed a gap voltage ( V g ) higher than 5 mV. In an NbN/Al 0.942 Ni 0.058 N/NbN junction, its Josephson current I c was suppressed to approximately a third of a theoretical value under no magnetic field. Therefore, it would be possible to avoid Josephson noise in magnetic barrier junctions with a much smaller magnetic field than junctions with conventional barriers. The Ni ion area density dependence of I c suppression ratio was identical for both types of junction, suggesting that the area density of magnetic ions is the factor that determines the I c suppression ratio. On the other hand, the extents of degradation of V g and increase in leakage current caused by the increase in Ni ion area density were smaller in MgO/NiO/MgO barrier junctions than in AlNiN barrier junctions. This suggests that the proximity effect of magnetic ions was weakened owing to the separation of Ni ions and NbN layers by the inserted thin MgO layers.