Electro-optic control and locking techniques are key ingredients of today's quantum optics experiments. We present an example of the superb technology pioneered by Jan Hall and how it has contributed to optical quantum information and communication.
In a quantum key distribution system, it is crucial to keep the extinction ratio of the coherent pulses stable. This means that the direct current bias point of the electro—optic modulator (EOM) used for generating coherent pulses must be locked. In this paper, an autobias control system based on a lock-in-amplifier for the EOM is introduced. Its drift information extracting theory and control method are analyzed comprehensively. The long term drift of the extinction ratio of the coherent pulses is measured by a single photon detector, which indicates that the autobias control system is effective for stabilizing the bias point of the EOM.
Current interferometric gravitational wave detectors were designed to be limited, in much of their sensitive \nband, by quantum noise in the form of shot noise (at high frequency) or quantum radiation pressure noise \n(at low frequency). In the current observation run (O3), a squeezed light source has been used to \nmanipulate quantum noise and surpass the limits imposed by the circulating laser power by injecting nonclassical states of the electromagnetic field, called squeezed vacuum states, in the interferometer's dark \nport. Recent O3 results show that this technique was able to reduce the shot noise contribution to the \nnoise spectral density by about one half. To surpass the so called standard quantum limit across the entire \nsensitivity band, an even more complex variation of this technique will be implemented, which requires the \nuse of a so called “filter cavity” to reflect the squeezed quantum field and rotate the squeezing angle as a \nfunction of frequency. \nThe performance of this techniques is however severely limited by light losses. One big contributor to \noptical losses is the mismatch between the squeezed vacuum beam, the beam circulating into the \ninterferometer and, in the near future, the filter cavity fundamental transverse spatial mode. \nTo be able to monitor and actively correct mode mismatch, an accurate, online sensing technique is \nneeded. A possible solution consists in the introduction of an Electro-Optic Lens (EOL) that can induce \nradio-frequency sidebands in the Laguerre-Gauss 10 (LG10) transverse mode of the beam. If the \nmodulation frequency is tuned in a way that one sideband is at the cavity LG10 frequency, then the \nresonance breaks the symmetry of the two sidebands and converts phase modulation into amplitude \nmodulation, making it possible to retrieve an error signal directly from the cavity reflected electric field \nwith the same single-element photodetector used for the Pound Drever Hall (PDH) locking technique. This \nerror signal carries information about the magnitude and nature of the mismatch, providing all is needed to \ninform a dedicated feedback loop with a suitable actuator to maintain the mismatch at or below the 1% \nlevel. \nThe goal of this thesis is to demonstrate the technique on a dedicated bench-top experiment employing an \nEOL prototype device. The EOL alignment and working point, as well as the cavity lock parameters were \noptimized in an already existing setup. Simulations and theoretical calculations of the cavity reflected field \nwere performed to evaluate the system non-idealities: both Electro-Optic Modulator (for PDH technique) \nand EOL modulations effects and interactions, as well as some system imperfections were considered. The \nsimulations confirm that this technique requires a stable cavity lock condition, and for this reason an \naccurate study and optimization of the feedback loop parameters was done. In conclusion, a \ncharacterization of the EOL error signal response to different mismatch conditions are presented.
This chapter focuses on the measurement of quantum noise, that is the fundamental noise we observe on the photocurrent when we detect optical beams with a large coherent amplitude using photodetectors. It also focuses on continuous wave laser beams and the noise associated with the intensity, amplitude, and phase of the light. Three different techniques are commonly used: direct detection, balanced detection, and homodyne detection. The choice depends on the properties of laser beam. Heterodyne detection is frequently used to determine the linewidth of an unknown laser. The intensity noise of a laser can be reduced using an electro-optic modulator and a feedback controller, known as a noise eater. The chapter explains Frequency Stabilization process and Locking of Cavities. It outlines the principles of the locking technique. The commonly used locking techniques include Pound-Drever-Hall Locking, tilt locking and optical injection locking.