Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Japanese Journal of Applied Physics

Estimation of Inductance for High-Tc dc-SQUID's in Coplanar Waveguide

Hiroyuki Fuke, Kazuo Saitoh, Tadashi Utagawa, Youichi Enomoto

Published Dec 1, 1996• 14 citations
Publisher

Abstract

We have investigated the electrical properties of high-T c dc-SQUID's formed in a coplanar waveguide, and discussed their applicability to single flux quantum (SFQ) circuits. The planar type Josephson junctions were fabricated in NdBa2Cu3O y (NBCO) superconducting thin films by a narrow-focused ion beam (FIB) irradiation technique. The critical current and normal resistance values of the Josephson junction at 4.2 K were 115 µA and 8 Ω, respectively. The inductance was estimated by applying a direct injection of the control current into the dc-SQUID loop and measuring the periodic voltage response. A loop inductance of 47 pH was obtained for a 25 µm-wide and 20 µm-long dc-SQUID at 4.2 K. It has been clarified that for a stable operation of SFQ logic circuits, a 10 µm-square dc-SQUID's are required.

DOI
10.1143/jjap.35.l1582

Related papers

Fundamental operation of single-flux-quantum circuits using coplanar-type high-T c SQUIDs

Hiroyuki Fuke, Kazuo Saitoh, Tadashi Utagawa +1 more

We have fabricated coplanar type dc SQUIDs using NdBa2Cu3Oy superconducting thin films and operated fundamental single-flux-quantum (SFQ) circuits. The Josephson junctions were made by the narrow-focused ion beam irradiation technique. For a 145 μm wide and 10 μm long logic SQUID having a critical current of 105 μA and an inductive parameter (βL) of 28, a store and a restore of the flux quantum have been demonstrated at temperatures of 4.2–30 K. These operations were performed with an input pulsewidth of 5 ns (5 ns was the shortest input pulse width available from our function generating equipment). These results show experimentally the possibility of high speed operation in all high-Tc superconducting digital circuits.

Applied Physics Letters•Nov 4, 1996•11 citations

YBa2Cu3O7 step-edge dc SQUID with coplanar control lines

H. Hasegawa, Y. Tarutani, Tokuumi Fukazawa +2 more

A dc superconducting quantum interference device (SQUID) with coplanar control lines has been fabricated from a single layer of YBa2Cu3O7 thin film. Step-edge junctions were formed using resist/Si double-mask layers. Current–voltage characteristics of this SQUID at 77 K show Shapiro steps under microwave irradiation and are qualitatively consistent with the resistively shunted junction (RSJ) model. The spacing between the closed loop and the coplanar control lines in the tested SQUIDs ranged from 0.2 to 1.5 μm. The measured output voltage-control current characteristics showed that the experimentally derived mutual inductances were a function of the spacing, in agreement with the calculated results. The typical mutual inductance for a spacing of 1.0 μm was ∼0.5 pH, which is adequate for detecting signals of flux-transfer logic gates in which the typical logic amplitude is ∼0.1 mA. A coplanar structure is thus useful for logic gate applications.

Applied Physics Letters•Nov 20, 1995•14 citations

Store–restore operation of flux quanta in coplanar type high Tc superconductive quantum interference devices

Hiroyuki Fuke, Kazuo Saitoh, Tadashi Utagawa +1 more

For a superconductive quantum interference device (SQUID) with rather large loop inductance for a single flux quantum, store–restore operation of flux quanta has been examined by external current pulses. To sense the stored flux quanta, the device includes another directly coupled SQUID as a magnetometer. Both of the coplanar type dc SQUIDs have been composed of Josephson junctions made by the narrow-focused ion beam irradiation technique in single-layer NdBa2Cu3O7−δ superconducting films. The SQUID has a critical current of 375 μA and an inductive parameter (βL) of 32. The number of stored flux quanta is controlled by the pulse signal height and the input terminal, but not by the number of pulses.

Journal of Applied Physics•Sep 1, 1998•1 citation

Niobium dc SQUIDs with Nanobridge Junctions

E.E. Mitchell, S. K. H. Lam

DC SQUIDs with outer loop size ∼10 μmx 10 μm have been fabricated with nanobridge Josephson junctions in thin Niobium films (25, 100 and 200 nm) using either electron beam or focused ion beam techniques. Such SQUIDs are ideally suited to incorporate into the centre strip of a superconducting coplanar waveguide. The current-voltage characteristics and magnetic field modulation of the SQUIDs are compared for the two methods. The temperature dependence of the critical current is quite linear for the e-beam devices whilst the focused ion beam devices fit an exponential. Here we also investigate trimming methods to reduce the critical currents of the nanojunctions fabricated in the thicker films, in order to improve the SQUID parameters at lower temperatures.

Physics Procedia•Jan 1, 2012•10 citations

Geometric Dependence of Washer Inductance for NbN DC SQUIDs

Qiyu Zhang, Huiwu Wang, Guanqun Li +4 more

Planar niobium nitride (NbN) dc superconducting quantum interference devices (SQUIDs) magnetometers were developed based on high-quality epitaxial NbN/AlN/NbN Josephson junctions for SQUID applications at higher operating temperatures. To improve the design of NbN dc SQUIDs, we measured the SQUID washer's inductance, which is a key SQUID parameter. A set of NbN dc SQUIDs with washers with different dimensions were implemented. The washer inductances were obtained from the periodic flux variation in the SQUIDs when a control current was injected directly into the SQUID washers; the results agree well with the ones calculated with a numerical simulation in InductEX software. We obtained an empirical expression to estimate the NbN SQUID inductance with washers with different geometric structures. Our results will be useful for designing NbN dc SQUID magnetometers in future.

IEEE Transactions on Applied Superconductivity•Apr 18, 2018•1 citation

Direct-injection high-Tc dc-SQUID with an upper YBa2Cu3O7−x ground plane

Hirotaka Terai, Mutsuo Hidaka, T. Satoh +1 more

We have fabricated direct-injection high-Tc superconducting quantum interference devices (SQUIDs) with integrated YBa2Cu3O7−x (YBCO) ground planes in the upper part of structure. The YBCO/PrBa2Cu3O7−x(PBCO)/YBCO edge junctions with 10-nm-thick PBCO barriers showed RSJ-like current-voltage (I–V) characteristics before and after the ground plane formation. We measured the voltage modulations of these SQUIDs with two different hole sizes to evaluate the line inductance. At a temperature of 30 K, the estimated line inductance under the ground plane was about 1.0 pH/□, while the estimated line inductance without the ground plane was 2.8 pH/□.

Applied Physics Letters•May 19, 1997•28 citations
We have investigated the electrical properties of high-T c dc-SQUID's formed in a coplanar waveguide, and discussed their applicability to single flux quantum (SFQ) circuits. The planar type Josephson junctions were fabricated in NdBa2Cu3O y (NBCO) superconducting thin films by a narrow-focused ion beam (FIB) irradiation technique. The critical current and normal resistance values of the Josephson junction at 4.2 K were 115 µA and 8 Ω, respectively. The inductance was estimated by applying a direct injection of the control current into the dc-SQUID loop and measuring the periodic voltage response. A loop inductance of 47 pH was obtained for a 25 µm-wide and 20 µm-long dc-SQUID at 4.2 K. It has been clarified that for a stable operation of SFQ logic circuits, a 10 µm-square dc-SQUID's are required.
We have fabricated coplanar type dc SQUIDs using NdBa2Cu3Oy superconducting thin films and operated fundamental single-flux-quantum (SFQ) circuits. The Josephson junctions were made by the narrow-focused ion beam irradiation technique. For a 145 μm wide and 10 μm long logic SQUID having a critical current of 105 μA and an inductive parameter (βL) of 28, a store and a restore of the flux quantum have been demonstrated at temperatures of 4.2–30 K. These operations were performed with an input pulsewidth of 5 ns (5 ns was the shortest input pulse width available from our function generating equipment). These results show experimentally the possibility of high speed operation in all high-Tc superconducting digital circuits.
A dc superconducting quantum interference device (SQUID) with coplanar control lines has been fabricated from a single layer of YBa2Cu3O7 thin film. Step-edge junctions were formed using resist/Si double-mask layers. Current–voltage characteristics of this SQUID at 77 K show Shapiro steps under microwave irradiation and are qualitatively consistent with the resistively shunted junction (RSJ) model. The spacing between the closed loop and the coplanar control lines in the tested SQUIDs ranged from 0.2 to 1.5 μm. The measured output voltage-control current characteristics showed that the experimentally derived mutual inductances were a function of the spacing, in agreement with the calculated results. The typical mutual inductance for a spacing of 1.0 μm was ∼0.5 pH, which is adequate for detecting signals of flux-transfer logic gates in which the typical logic amplitude is ∼0.1 mA. A coplanar structure is thus useful for logic gate applications.
For a superconductive quantum interference device (SQUID) with rather large loop inductance for a single flux quantum, store–restore operation of flux quanta has been examined by external current pulses. To sense the stored flux quanta, the device includes another directly coupled SQUID as a magnetometer. Both of the coplanar type dc SQUIDs have been composed of Josephson junctions made by the narrow-focused ion beam irradiation technique in single-layer NdBa2Cu3O7−δ superconducting films. The SQUID has a critical current of 375 μA and an inductive parameter (βL) of 32. The number of stored flux quanta is controlled by the pulse signal height and the input terminal, but not by the number of pulses.
DC SQUIDs with outer loop size ∼10 μmx 10 μm have been fabricated with nanobridge Josephson junctions in thin Niobium films (25, 100 and 200 nm) using either electron beam or focused ion beam techniques. Such SQUIDs are ideally suited to incorporate into the centre strip of a superconducting coplanar waveguide. The current-voltage characteristics and magnetic field modulation of the SQUIDs are compared for the two methods. The temperature dependence of the critical current is quite linear for the e-beam devices whilst the focused ion beam devices fit an exponential. Here we also investigate trimming methods to reduce the critical currents of the nanojunctions fabricated in the thicker films, in order to improve the SQUID parameters at lower temperatures.
Planar niobium nitride (NbN) dc superconducting quantum interference devices (SQUIDs) magnetometers were developed based on high-quality epitaxial NbN/AlN/NbN Josephson junctions for SQUID applications at higher operating temperatures. To improve the design of NbN dc SQUIDs, we measured the SQUID washer's inductance, which is a key SQUID parameter. A set of NbN dc SQUIDs with washers with different dimensions were implemented. The washer inductances were obtained from the periodic flux variation in the SQUIDs when a control current was injected directly into the SQUID washers; the results agree well with the ones calculated with a numerical simulation in InductEX software. We obtained an empirical expression to estimate the NbN SQUID inductance with washers with different geometric structures. Our results will be useful for designing NbN dc SQUID magnetometers in future.
We have fabricated direct-injection high-Tc superconducting quantum interference devices (SQUIDs) with integrated YBa2Cu3O7−x (YBCO) ground planes in the upper part of structure. The YBCO/PrBa2Cu3O7−x(PBCO)/YBCO edge junctions with 10-nm-thick PBCO barriers showed RSJ-like current-voltage (I–V) characteristics before and after the ground plane formation. We measured the voltage modulations of these SQUIDs with two different hole sizes to evaluate the line inductance. At a temperature of 30 K, the estimated line inductance under the ground plane was about 1.0 pH/□, while the estimated line inductance without the ground plane was 2.8 pH/□.