Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Design and optimization of NbCN/PbBi mixer elements for heterodyne receivers

A. W. Lichtenberger, A. S. Lewis, Robert J. Mattauch

Published Jan 1, 1985• 0 citations
OpenAlex

Abstract

Superconductor-Insulator-Superconductor (SIS) quantum mixers provide a relatively new approach to millimeter wave mixing potentially offering conversion gain, a low local oscillator power demand and potential mixer temperatures near the quantum limit. This paper presents device modeling and fabrication development for NbCN lead-alloy submicron edge-contact SIS mixers for use at 115 GHz.

Related papers

Optimization of SIS mixer elements

Robert J. Mattauch

Superconductor-Insulator-Superconductor (SIS) quantum mixers provide an approach to millimeter wave mixing - potentially offering conversion gain, a low local oscillator power demand, and potential mixer noise temperatures near the quantum limit. The development of a reliable fabrication technology for producing such high quality SIS devices for mixer applications in radio astronomy is the focus of the work.

•Dec 1, 1985•0 citations

Niobium nitride devices for SIS mixers

Edward J. Cukauskas, William L. Carter, Marty Nisenoff

The superconductor-insulator-superconductor (SIS) tunnel junction is an attractive candidate for millimeter wave mixers offering conversion gain and quantum limited noise.1SIS mixers have been operated at 36 GHz with a single sideband noise temperature of 3.7K which is within a factor of 2 of quantum limited performance.2These results were obtained with devices fabricated from lead alloy technology. While this technology is very useful for the demonstration of quantum limited noise an all refractory junction technology would be desirable as it would have the advantages of being mechanically rugged, cycle well between room temperature and 4K be resistant to radiation damage and have enhanced high frequency response.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Dec 1, 1985•0 citations

SIS mixers for low noise millimetre-wave heterodyne receivers

Steven R. Davies, C. T. Cunningham, Leslie T. Little

The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.

•Mar 22, 1988•0 citations

Design and fabrication of 800- to 900-GHz Pb-alloy SIS mixing device incorporating an on-substrate tuning element

Keith Tame, Marc C. Price, Leslie T. Little

The use of SIS (Superconductor-Insulator-Superconductor) devices as the mixing element, in ultra-sensitive heterodyne receivers for use in radio astronomy is well established. In attempting to exploit the last main submillimeter atmospheric window we are developing a Pb-alloy SIS mixer to work in the frequency band 800 - 900 GHz. In this paper we address some of the problems with working at frequencies above the energy gap of a superconducting alloy. We also present initial results obtained from Pb-alloy SIS junctions fabricated at the University of Kent at Canterbury (UKC).

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jul 31, 1998•0 citations

Study on Frequency Up-Conversion Characteristic in SIS Mixers and its Application

雄人 上月

Superconductor-insulator-superconductor (SIS) junctions, which are low-noise heterodyne mixers, have been used as frequency converters.In recent years, ultralow power consumption of receiver components has become essential to increase the scale and integration of receiver systems.In this paper, we explore the performance of SIS mixers, which have been widely used as a low-noise frequency down-converter in the field of radio astronomy, as a frequency up-converter and discuss the possibility of its application to low-noise microwave amplifiers with ultra-low power consumption.In this study, we investigate the characteristics of the SIS upconverters, clarifying the conditions for gain generation in up-conversion.This research will lead to the realization of ultra-low-power amplifiers based on SIS mixers, which will solve the problem of increasing power consumption in future receiver systems.Chapter 1 describes the background of the research, including the ongoing problem of the increasing scale of receiving systems and the associated power consumption of low-noise amplifiers in the field of high-sensitivity reception, the history of the research on heterodyne mixing using SIS mixers, and the significance and policy of the research.Chapter 2 describes the theoretical background relevant to this study and discusses the basic properties of SIS junctions as heterodyne mixers.In Chapter 3, we describe the numerical analysis conducted to clarify the upconversion characteristics of the SIS mixer.In Chapter 4, we describe the mixing characteristics of SIS junctions at 40 GHz by constructing a new experimental system that directly measures the characteristics of heterodyne mixers. IVIn Chapter 5, a new experimental system is constructed using an existing SIS mixer developed as a down-converter for W-band, and the up-conversion gain characteristics in the 100 GHz band are described.Chapter 6 describes a demonstration experiment that shows the potential of the SIS mixer to be applied to ultra-low-power low-noise microwave amplifiers.Chapter 7 summarizes the paper and discusses the challenges and prospects for future realization and application of ultra-low-power amplifiers.V

•Mar 24, 2022•0 citations

A millimeter unilateral finline SIS mixer with a wide IF bandwidth

Yangjun Zhou

Superconductor-Insulator-Superconductor (SIS) tunnel junction mixers are now commonly used in as- tronomical receivers at (sub)millimeter wavelengths because of their superb sensitivity, high dynamic range and stability of operation. Niobium SIS mixers operating at frequencies well below the super- conducting gap (∼680 GHz) have already achieved quantum limited sensitivity. Therefore to further enhance the receiver sensitivity, increasing the Intermediate Frequency (IF) bandwidth of SIS mixers has became crucial. This thesis focuses on the theoretical modeling, design and experimental verifi- cation of Nb SIS mixers operating around 230 GHz with a wide IF bandwidth of 1–15 GHz. These mixers were designed for a single baseline heterodyne interferometer (GUBBINS), which is being built to observe the Sunyaev-Zel’dovich effect in the Cosmic Microwave Background. The combination of wide IF bandwidth SIS mixers and complex analogue correlators will allow GUBBINS to feature high surface brightness sensitivity, that helps to distinguish the weak SZ effect from the background noise. The SIS mixer detector system was assembled inside the GUBBINS cryostat together with the IF electronics and RF/LO optical systems. Low noise temperatures of around 71 K were then measured in the GUBBINS system. The Nb SIS mixer we have developed uses a unilateral finline and fully integrated planar circuits deposited on a silicon substrate, to couple the electromagnetic radiation from the waveguide into the SIS junction. The finline mixer allows a broad-band RF coupling, an easy integration of the on-chip planar circuits and an easy-to-fabricate mixer block. To achieve a wide IF bandwidth, the output impedance of the SIS mixer was well matched to the input impedance of the amplifier by a multi-stage microstrip circuit. Additionally, the planar circuit of the SIS mixer was also designed to have a small lumped inductance and capacitance. The SIS mixer chip was extensively simulated by rigorous electromagnetic software (HFSS) and the S-parameter was exported to a quantum mixing package SuperMix to produce a full-wave model of the mixer. Experimental testing yielded a best noise temperature of 50 K with an average noise temperature of 75 K over an RF bandwidth of 160 GHz– 260 GHz. We have performed thorough experimental and computational investigation of the IF system in particular the constraints on the bandwidth caused by the lumped element capacitance of the mixer chip and the matching of the output impedance of the mixer to the IF amplifier. Our conclusion is that a bandwidth of 1–15 GHz could be achieved using our mixer design, subject to the performance of the amplifier. Finally, a variable temperature load system was successfully developed and tested inside the cryostat, to avoid the losses from the room-temperature optics. We have showed that the noise temperature of the SIS detector could be reduced by as much as 15 K by testing the mixer using a variable temperature load inside the cryostat.

•Jan 1, 2013•0 citations
Superconductor-Insulator-Superconductor (SIS) quantum mixers provide a relatively new approach to millimeter wave mixing potentially offering conversion gain, a low local oscillator power demand and potential mixer temperatures near the quantum limit. This paper presents device modeling and fabrication development for NbCN lead-alloy submicron edge-contact SIS mixers for use at 115 GHz.
The superconductor-insulator-superconductor (SIS) tunnel junction is an attractive candidate for millimeter wave mixers offering conversion gain and quantum limited noise.1SIS mixers have been operated at 36 GHz with a single sideband noise temperature of 3.7K which is within a factor of 2 of quantum limited performance.2These results were obtained with devices fabricated from lead alloy technology. While this technology is very useful for the demonstration of quantum limited noise an all refractory junction technology would be desirable as it would have the advantages of being mechanically rugged, cycle well between room temperature and 4K be resistant to radiation damage and have enhanced high frequency response.
The development of ultra-low-noise receivers at frequencies of >200 GHz is primarily driven by astronomical applications. The most sensitive millimeter-wave receivers that have presently been constructed make use of the strong mixing afforded by superconductor-insulator-superconductor (SIS) tunnel junctions. In a collaborative project between UKC and RAL, a 230 GHz laboratory receiver has been built using a lead alloy SIS junction as the mixing element, mounted in 4:1 reduced-height waveguide, terminated at one end with a circular cross-section, adjustable backshort. Best results indicate a double-sideband receiver noise temperature of T/sub R/(DSB) approximately=120 K, which represents state-of-the-art performance at this frequency. Initial difficulties in achieving good mixing performance prompted an investigation into the importance of the 'quality' of mixer block backshort tuning elements. An analysis of the mixer equivalent circuit is presented which allows for loss in a non-ideal mixer block, and 3-port mixer model calculations are discussed which incorporate this analysis into the Tucker quantum theory of mixing.
The use of SIS (Superconductor-Insulator-Superconductor) devices as the mixing element, in ultra-sensitive heterodyne receivers for use in radio astronomy is well established. In attempting to exploit the last main submillimeter atmospheric window we are developing a Pb-alloy SIS mixer to work in the frequency band 800 - 900 GHz. In this paper we address some of the problems with working at frequencies above the energy gap of a superconducting alloy. We also present initial results obtained from Pb-alloy SIS junctions fabricated at the University of Kent at Canterbury (UKC).
Superconductor-insulator-superconductor (SIS) junctions, which are low-noise heterodyne mixers, have been used as frequency converters.In recent years, ultralow power consumption of receiver components has become essential to increase the scale and integration of receiver systems.In this paper, we explore the performance of SIS mixers, which have been widely used as a low-noise frequency down-converter in the field of radio astronomy, as a frequency up-converter and discuss the possibility of its application to low-noise microwave amplifiers with ultra-low power consumption.In this study, we investigate the characteristics of the SIS upconverters, clarifying the conditions for gain generation in up-conversion.This research will lead to the realization of ultra-low-power amplifiers based on SIS mixers, which will solve the problem of increasing power consumption in future receiver systems.Chapter 1 describes the background of the research, including the ongoing problem of the increasing scale of receiving systems and the associated power consumption of low-noise amplifiers in the field of high-sensitivity reception, the history of the research on heterodyne mixing using SIS mixers, and the significance and policy of the research.Chapter 2 describes the theoretical background relevant to this study and discusses the basic properties of SIS junctions as heterodyne mixers.In Chapter 3, we describe the numerical analysis conducted to clarify the upconversion characteristics of the SIS mixer.In Chapter 4, we describe the mixing characteristics of SIS junctions at 40 GHz by constructing a new experimental system that directly measures the characteristics of heterodyne mixers. IVIn Chapter 5, a new experimental system is constructed using an existing SIS mixer developed as a down-converter for W-band, and the up-conversion gain characteristics in the 100 GHz band are described.Chapter 6 describes a demonstration experiment that shows the potential of the SIS mixer to be applied to ultra-low-power low-noise microwave amplifiers.Chapter 7 summarizes the paper and discusses the challenges and prospects for future realization and application of ultra-low-power amplifiers.V
Superconductor-Insulator-Superconductor (SIS) tunnel junction mixers are now commonly used in as- tronomical receivers at (sub)millimeter wavelengths because of their superb sensitivity, high dynamic range and stability of operation. Niobium SIS mixers operating at frequencies well below the super- conducting gap (∼680 GHz) have already achieved quantum limited sensitivity. Therefore to further enhance the receiver sensitivity, increasing the Intermediate Frequency (IF) bandwidth of SIS mixers has became crucial. This thesis focuses on the theoretical modeling, design and experimental verifi- cation of Nb SIS mixers operating around 230 GHz with a wide IF bandwidth of 1–15 GHz. These mixers were designed for a single baseline heterodyne interferometer (GUBBINS), which is being built to observe the Sunyaev-Zel’dovich effect in the Cosmic Microwave Background. The combination of wide IF bandwidth SIS mixers and complex analogue correlators will allow GUBBINS to feature high surface brightness sensitivity, that helps to distinguish the weak SZ effect from the background noise. The SIS mixer detector system was assembled inside the GUBBINS cryostat together with the IF electronics and RF/LO optical systems. Low noise temperatures of around 71 K were then measured in the GUBBINS system. The Nb SIS mixer we have developed uses a unilateral finline and fully integrated planar circuits deposited on a silicon substrate, to couple the electromagnetic radiation from the waveguide into the SIS junction. The finline mixer allows a broad-band RF coupling, an easy integration of the on-chip planar circuits and an easy-to-fabricate mixer block. To achieve a wide IF bandwidth, the output impedance of the SIS mixer was well matched to the input impedance of the amplifier by a multi-stage microstrip circuit. Additionally, the planar circuit of the SIS mixer was also designed to have a small lumped inductance and capacitance. The SIS mixer chip was extensively simulated by rigorous electromagnetic software (HFSS) and the S-parameter was exported to a quantum mixing package SuperMix to produce a full-wave model of the mixer. Experimental testing yielded a best noise temperature of 50 K with an average noise temperature of 75 K over an RF bandwidth of 160 GHz– 260 GHz. We have performed thorough experimental and computational investigation of the IF system in particular the constraints on the bandwidth caused by the lumped element capacitance of the mixer chip and the matching of the output impedance of the mixer to the IF amplifier. Our conclusion is that a bandwidth of 1–15 GHz could be achieved using our mixer design, subject to the performance of the amplifier. Finally, a variable temperature load system was successfully developed and tested inside the cryostat, to avoid the losses from the room-temperature optics. We have showed that the noise temperature of the SIS detector could be reduced by as much as 15 K by testing the mixer using a variable temperature load inside the cryostat.