Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Sensitive, 3D micromotion compensation in a surface-electrode ion trap

Amira M. Eltony

Published Jan 1, 2013• 4 citations
OpenAlex

Abstract

Following successful demonstrations of quantum algorithms and error correction with a handful of trapped ions in a macroscopic, machined Paul trap, there is a growing effort to move towards microfabricated traps with all the electrodes on a single chip.These traps, known as surface-electrode ion traps, are more amenable to being shrunk in size and replicated, or integrated with optical components and electronic devices.However, in the shift towards surface-electrode traps, and as traps are miniaturized in general, laser beams are brought closer to electrode surfaces, exacerbating laserinduced charging.Because of their charge, trapped ions are extremely sensitive to stray charges that accumulate on the trap surface.The DC potentials caused by stray charge displace the ion from the null of the RF trapping field, resulting in a fast, driven motion of the ion (known as micromotion) which hinders quantum operations by broadening transitions and causing decoherence.In a surface trap, micromotion detection is difficult as the laser beams used for measurement typically cannot crash into the trap, obscuring ion offsets out of the trap plane.Existing methods for micromotion detection permit ion positioning accurate to the ground state wavepacket size (of order 10 nm), but cannot identify ion offsets out of the trap plane with the same accuracy.Schemes for sensitive compensation often have restrictive requirements such as access to a narrow atomic transition.We introduce a new approach, which permits out-of-plane micromotion compensation to within 10s of nanometers with minimal overhead.Our technique synchronously detects ion excitation along the trap axes when it is driven by secular-frequency sidebands added to the RF electrodes; the excitation amplitude is proportional to the offset from the RF null.We make a detailed theoretical comparison with other techniques for micromotion compensation and demonstrate our technique experimentally.

Related papers

Ion-trajectory analysis for micromotion minimization and the measurement of small forces

Timm F. Gloger, Peter Kaufmann, Delia Kaufmann +4 more

For experiments with ions confined in a Paul trap, minimization of micromotion is often essential. In order to diagnose and compensate micromotion we have implemented a method that allows for finding the position of the radio-frequency (rf) null reliably and efficiently, in principle, without any variation of direct current (dc) voltages. We apply a trap modulation technique and focus-scanning imaging to extract three-dimensional ion positions for various rf drive powers and analyze the power dependence of the equilibrium position of the trapped ion. In contrast to commonly used methods, the search algorithm directly makes use of a physical effect as opposed to efficient numerical minimization in a high-dimensional parameter space. Using this method we achieve a compensation of the residual electric field that causes excess micromotion in the radial plane of a linear Paul trap down to $0.09\phantom{\rule{4pt}{0ex}}\text{V}\phantom{\rule{0.16em}{0ex}}{\text{m}}^{\ensuremath{-}1}$. Additionally, the precise position determination of a single harmonically trapped ion employed here can also be utilized for the detection of small forces. This is demonstrated by determining light pressure forces with a precision of 135 yN. As the method is based on imaging only, it can be applied to several ions simultaneously and is independent of laser direction and thus well suited to be used with, for example, surface-electrode traps.

arXiv:1503.07031•Physical Review A•Oct 27, 2015•45 citations

Micromotion minimisation by synchronous detection of parametrically excited motion

D. P. Nadlinger, P. Drmota, D. Main +6 more

Precise control of charged particles in radio-frequency (Paul) traps requires minimising excess micromotion induced by stray electric fields. We present a method to detect and compensate such fields through amplitude modulation of the radio-frequency trapping field. Modulation at frequencies close to the motional modes of the trapped particle excites coherent motion whose amplitude linearly depends on the stray field. In trapped-ion experiments, this motion can be detected by recording the arrival times of photons scattered during laser cooling. Only a single laser beam is required to resolve fields in multiple directions. In a demonstration using a $^{88}\mathrm{Sr}^{+}$ ion in a surface electrode trap, we achieve a sensitivity of $0.1\, \mathrm{V}\, \mathrm{m}^{-1}\, /\, \sqrt{\mathrm{Hz}}$ and a minimal uncertainty of $0.015\, \mathrm{V}\, \mathrm{m}^{-1}$.

arXiv:2107.00056•Jun 30, 2021•13 citations

Precise micromotion compensation of a tilted ion chain

Craig Hogle, Ashlyn D. Burch, Jonathan David Sterk +9 more

Excess micromotion can be a substantial source of errors in trapped-ion based quantum processors and clocks due to the sensitivity of the internal states of the ion to external fields and motion. This problem can be fixed by compensating background electric fields in order to position ions at the RF node and minimize their driven micromotion. Here we describe techniques for compensating ion chains in scalable surface ion traps. These traps are capable of cancelling stray electric fields with fine spatial resolution in order to compensate multiple closely spaced ions due to their large number of relatively small control electrodes. We demonstrate a technique that compensates an ion chain to better than 5 V/m and within 0.1 degrees of chain rotation.

Frontiers in Quantum Science and Technology•Apr 22, 2024•6 citations

Three-dimensional micromotion compensation protocols for an RF ion trap

Ryoichi Saito, Takashi Mukaiyama

We propose and demonstrate four procedures for three-dimensional micromotion compensation by combining two methods: the RF-photon correlation method and the displacement method based on trap RF amplitude modulation. In ion traps, the structure of the electrodes or the vacuum chamber may restrict the laser beam incidence direction, causing a limitation in the compensation scheme. We present four protocols, ensuring that at least one of them can be applied to experimental systems with various individual constraints. We also discuss the compensation accuracy and practical applicability of each of these four approaches. This work provides a practical guideline for performing full three-axis micromotion compensation and contributes to the advancement of endcap traps, which are highly suitable for single-ion trapping.

arXiv:2508.11162•AIP Advances•Nov 1, 2025•0 citations

Optimizing RF/DC Electrode Layouts in Ion Traps: Minimizing Micromotion Through Geometric Configuration for Enhanced Confinement and Laser Cooling Access

Kaz Bano

Ion traps are a foundational technology in quantum information processing, precision spectroscopy and foundational physics tests. At the heart of their performance is the inhibition of micromotion, an oscillation of ions through imperfect trapping potentials, that restricts the laser cooling efficiency, coherence times, and the accuracy of measurements. The paper provides a systematic computational analysis of four different electrode geometries (Linear Paul, Segmented, Surface and Ring) in 24 different RF / DC configurations (C01-C24) and 13 performance parameters that comprise trap depth (0.62 1.48 eV), radial secular frequency (1,100 1 Multi-objective optimization with weighted scoring of these metrics indicates that Ring trap geometry scores the highest total (80.2/100), followed by Linear Paul (72.0), Segmented (67.0) and Surface (55.1) configurations. ANOVA (one-way) statistically verified the presence of statistically significant inter-geometry differences in micro-motions amplitude (F = 18.43, p < .001) and cooling efficiency (F = 22.17, p < .001), with Tukey HSD post-hoc revealed that the most significant difference was between the Ring and the Surface. The Pearson correlation analysis shows that RF drive voltage and micromotion amplitude (r = -0.94 to -0.99) and cooling efficiency and micromotion (r = -1.00) have near-perfect inverse correlations, which prove that the quality of confinement is regulated by electrode geometry, RF amplitude, and spacing. These results give quantitative design principles of next-generation ion traps in quantum computing and atomic clock. Keywords: ion trap, micromotion minimization, RF/DC electrode optimization, laser cooling, Mathieu stability, secular frequency, quantum computing

Annual Methodological Archive Research Review•Jan 30, 2026•0 citations

Laser-induced charging of microfabricated ion traps

Shannon X. Wang, Guang Hao Low, Nathan S. Lachenmyer +3 more

Electrical charging of metal surfaces due to photoelectric generation of carriers is of concern in trapped ion quantum computation systems, due to the high sensitivity of the ions’ motional quantum states to deformation of the trapping potential. The charging induced by typical laser frequencies involved in Doppler cooling and quantum control is studied here, with microfabricated surface-electrode traps made of aluminum, copper, and gold, operated at 6 K with a single Sr+ ion trapped 100 μm above the trap surface. The lasers used are at 370, 405, 460, and 674 nm, and the typical photon flux at the trap is 1014 photons/cm2/sec. Charging is detected by monitoring the ion’s micromotion signal, which is related to the number of charges created on the trap. A wavelength and material dependence of the charging behavior is observed: Lasers at lower wavelengths cause more charging, and aluminum exhibits more charging than copper or gold. We describe the charging dynamic based on a rate-equation approach.

arXiv:1108.0092•Journal of Applied Physics•Nov 15, 2011•50 citations
Following successful demonstrations of quantum algorithms and error correction with a handful of trapped ions in a macroscopic, machined Paul trap, there is a growing effort to move towards microfabricated traps with all the electrodes on a single chip.These traps, known as surface-electrode ion traps, are more amenable to being shrunk in size and replicated, or integrated with optical components and electronic devices.However, in the shift towards surface-electrode traps, and as traps are miniaturized in general, laser beams are brought closer to electrode surfaces, exacerbating laserinduced charging.Because of their charge, trapped ions are extremely sensitive to stray charges that accumulate on the trap surface.The DC potentials caused by stray charge displace the ion from the null of the RF trapping field, resulting in a fast, driven motion of the ion (known as micromotion) which hinders quantum operations by broadening transitions and causing decoherence.In a surface trap, micromotion detection is difficult as the laser beams used for measurement typically cannot crash into the trap, obscuring ion offsets out of the trap plane.Existing methods for micromotion detection permit ion positioning accurate to the ground state wavepacket size (of order 10 nm), but cannot identify ion offsets out of the trap plane with the same accuracy.Schemes for sensitive compensation often have restrictive requirements such as access to a narrow atomic transition.We introduce a new approach, which permits out-of-plane micromotion compensation to within 10s of nanometers with minimal overhead.Our technique synchronously detects ion excitation along the trap axes when it is driven by secular-frequency sidebands added to the RF electrodes; the excitation amplitude is proportional to the offset from the RF null.We make a detailed theoretical comparison with other techniques for micromotion compensation and demonstrate our technique experimentally.
For experiments with ions confined in a Paul trap, minimization of micromotion is often essential. In order to diagnose and compensate micromotion we have implemented a method that allows for finding the position of the radio-frequency (rf) null reliably and efficiently, in principle, without any variation of direct current (dc) voltages. We apply a trap modulation technique and focus-scanning imaging to extract three-dimensional ion positions for various rf drive powers and analyze the power dependence of the equilibrium position of the trapped ion. In contrast to commonly used methods, the search algorithm directly makes use of a physical effect as opposed to efficient numerical minimization in a high-dimensional parameter space. Using this method we achieve a compensation of the residual electric field that causes excess micromotion in the radial plane of a linear Paul trap down to $0.09\phantom{\rule{4pt}{0ex}}\text{V}\phantom{\rule{0.16em}{0ex}}{\text{m}}^{\ensuremath{-}1}$. Additionally, the precise position determination of a single harmonically trapped ion employed here can also be utilized for the detection of small forces. This is demonstrated by determining light pressure forces with a precision of 135 yN. As the method is based on imaging only, it can be applied to several ions simultaneously and is independent of laser direction and thus well suited to be used with, for example, surface-electrode traps.
Precise control of charged particles in radio-frequency (Paul) traps requires minimising excess micromotion induced by stray electric fields. We present a method to detect and compensate such fields through amplitude modulation of the radio-frequency trapping field. Modulation at frequencies close to the motional modes of the trapped particle excites coherent motion whose amplitude linearly depends on the stray field. In trapped-ion experiments, this motion can be detected by recording the arrival times of photons scattered during laser cooling. Only a single laser beam is required to resolve fields in multiple directions. In a demonstration using a 88Sr+^{88}\mathrm{Sr}^{+}88Sr+ ion in a surface electrode trap, we achieve a sensitivity of 0.1 V m−1 / Hz0.1\, \mathrm{V}\, \mathrm{m}^{-1}\, /\, \sqrt{\mathrm{Hz}}0.1Vm−1/Hz​ and a minimal uncertainty of 0.015 V m−10.015\, \mathrm{V}\, \mathrm{m}^{-1}0.015Vm−1.
Excess micromotion can be a substantial source of errors in trapped-ion based quantum processors and clocks due to the sensitivity of the internal states of the ion to external fields and motion. This problem can be fixed by compensating background electric fields in order to position ions at the RF node and minimize their driven micromotion. Here we describe techniques for compensating ion chains in scalable surface ion traps. These traps are capable of cancelling stray electric fields with fine spatial resolution in order to compensate multiple closely spaced ions due to their large number of relatively small control electrodes. We demonstrate a technique that compensates an ion chain to better than 5 V/m and within 0.1 degrees of chain rotation.
We propose and demonstrate four procedures for three-dimensional micromotion compensation by combining two methods: the RF-photon correlation method and the displacement method based on trap RF amplitude modulation. In ion traps, the structure of the electrodes or the vacuum chamber may restrict the laser beam incidence direction, causing a limitation in the compensation scheme. We present four protocols, ensuring that at least one of them can be applied to experimental systems with various individual constraints. We also discuss the compensation accuracy and practical applicability of each of these four approaches. This work provides a practical guideline for performing full three-axis micromotion compensation and contributes to the advancement of endcap traps, which are highly suitable for single-ion trapping.
Ion traps are a foundational technology in quantum information processing, precision spectroscopy and foundational physics tests. At the heart of their performance is the inhibition of micromotion, an oscillation of ions through imperfect trapping potentials, that restricts the laser cooling efficiency, coherence times, and the accuracy of measurements. The paper provides a systematic computational analysis of four different electrode geometries (Linear Paul, Segmented, Surface and Ring) in 24 different RF / DC configurations (C01-C24) and 13 performance parameters that comprise trap depth (0.62 1.48 eV), radial secular frequency (1,100 1 Multi-objective optimization with weighted scoring of these metrics indicates that Ring trap geometry scores the highest total (80.2/100), followed by Linear Paul (72.0), Segmented (67.0) and Surface (55.1) configurations. ANOVA (one-way) statistically verified the presence of statistically significant inter-geometry differences in micro-motions amplitude (F = 18.43, p < .001) and cooling efficiency (F = 22.17, p < .001), with Tukey HSD post-hoc revealed that the most significant difference was between the Ring and the Surface. The Pearson correlation analysis shows that RF drive voltage and micromotion amplitude (r = -0.94 to -0.99) and cooling efficiency and micromotion (r = -1.00) have near-perfect inverse correlations, which prove that the quality of confinement is regulated by electrode geometry, RF amplitude, and spacing. These results give quantitative design principles of next-generation ion traps in quantum computing and atomic clock. Keywords: ion trap, micromotion minimization, RF/DC electrode optimization, laser cooling, Mathieu stability, secular frequency, quantum computing
Electrical charging of metal surfaces due to photoelectric generation of carriers is of concern in trapped ion quantum computation systems, due to the high sensitivity of the ions’ motional quantum states to deformation of the trapping potential. The charging induced by typical laser frequencies involved in Doppler cooling and quantum control is studied here, with microfabricated surface-electrode traps made of aluminum, copper, and gold, operated at 6 K with a single Sr+ ion trapped 100 μm above the trap surface. The lasers used are at 370, 405, 460, and 674 nm, and the typical photon flux at the trap is 1014 photons/cm2/sec. Charging is detected by monitoring the ion’s micromotion signal, which is related to the number of charges created on the trap. A wavelength and material dependence of the charging behavior is observed: Lasers at lower wavelengths cause more charging, and aluminum exhibits more charging than copper or gold. We describe the charging dynamic based on a rate-equation approach.