Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Superconducting Receiver Techniques.

A. DiNardo, E. Sard, Frank R. Arams, J. G. Smith

Published Sep 1, 1969• 0 citations
OpenAlex

Abstract

Abstract : The report covers research on microwave superconducting receiver techniques. An analysis of Josephson mixer operation, including characterization into a mathematical model suitable for analytical and computer study and a rigorous formulation of the generation of steps due to microwaves in the DC I-V characteristic, has been carried out. Experimental observation of the Josephson mixing action at 10 to 15 GHz has been obtained and is in agreement with the theory developed. The conversion loss, noise factor, and sensitivity of Josephson mixers have been measured. Using a point contact junction at 13 GHz, a minimum detectable signal of -90 dbm/MHz (measured) and -105 dbm/MHz (corrected) was obtained. Superconducting, miniature microstrip resonators operating at 10 to 15 GHz have been constructed using vacuum-deposited lead on low-loss sintered alumina substrate. Unloaded Q's (at 14.3 GHz) as high as 200,000 and 500,000 have been measured at 4.2 and 1.8 K respectively. The vacuum deposition technique used would permit the simulataneous fabrication of large numbers of miniature multielement filters and preselectors with low insertion loss and good skirt rejection. (Author)

Related papers

Superconducting Microwave Mixers Utilizing Josephson Junctions

A. DiNardo, E. Sard

Microwave superconducting mixers operating at 10–13 GHz utilizing Josephson junctions have been investigated analytically and experimentally. Measurements on mixer sensitivity were carried out at 13 GHz using waveguide-mounted experimental point-contact Josephson junctions at 4.2 K. Results showed sensitivities of −90 dBm/MHz (10−18 W/Hz) which included mismatch losses encountered in the waveguide structure. The Josephson junction mixing mechanism was analyzed on the basis of small-signal modulation of the staircase like dc I-V characteristics. It was shown that a small-signal microwave excitation results in an ac lateral shift of the regions between steps, such that: (a) Optimum Josephson mixing occurs halfway between steps. (b) Mixing occurs between all steps with maximum conversion efficiency between the zero and first step. (c) Predicted low conversion loss and possibly internal gain for a matched mixer. The analytical model was simulated by a digital computer and the behavior of the Josephson mixer predicted for various conditions of excitation. The model chosen for the analysis and the computer simulation is based on the simplest assumptions concerning bulk-formed Josephson junctions. In the laboratory an external local oscillator set 60 MHz below the signal frequency was used to induce the well-known step structure in the dc I-V characteristic of the point-contact Josephson junction. Mixing of the Lo and signal was found to occur between constant voltage steps in agreement with both analysis and computer simulation. The correctness of the model is demonstrated by the agreement between the theory and experiment.

Journal of Applied Physics•Jan 1, 1971•7 citations

Superconducting Microstrip High-Q Microwave Resonators

A. DiNardo, J. G. Smith, Frank R. Arams

Superconducting miniature microstrip resonators, operating at X band, have been constructed using vacuum-deposited lead on low-loss sintered alumina substrate. Unloaded Q's as high as 200 000 and 500 000 have been measured at 14.3 GHz at 4.2 and 1.8 K, respectively.

Journal of Applied Physics•Jan 1, 1971•17 citations

Josephson frequency conversion in the range 145–1600 GHz with Nb–Nb superconducting point contacts used as oscillator-mixer

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.

Journal of Applied Physics•Jun 1, 1974•13 citations

Frequency conversion with superconducting point contacts operating as oscillator-mixers and its application to the measurement of the linewidth of the Josephson current at very high frequency

G. Vernet, Robert Adde

The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.

Revue de Physique Appliquée•Jan 1, 1974•3 citations

Studies of noise in Josephson-effect mixers and their potential for submillimeter heterodyne detection

Robert J. Schoelkopf

NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.

•Nov 7, 2007•5 citations

Characterizations of High-Temperature Superconducting Step-Edge Josephson Junction Mixer

Dan Dan Bai, Jia Du, Yu Sheng He

We report the experimental evaluation of a high-temperature superconducting (HTS) Josephson mixer. The mixer is fabricated from a HTS step-edge junction on MgO substrate. The mixer device operates as a lower side-band down-converter from a radio frequency between 6 and 10 GHz to a 1-2 GHz intermediate frequency under the action of a local oscillator. The experimental results of the current-voltage characteristics, optimal bias conditions, dynamic range, linearity, conversion gain, and the temperature dependence of the mixer are presented.

IEEE Transactions on Applied Superconductivity•Aug 15, 2014•6 citations
Abstract : The report covers research on microwave superconducting receiver techniques. An analysis of Josephson mixer operation, including characterization into a mathematical model suitable for analytical and computer study and a rigorous formulation of the generation of steps due to microwaves in the DC I-V characteristic, has been carried out. Experimental observation of the Josephson mixing action at 10 to 15 GHz has been obtained and is in agreement with the theory developed. The conversion loss, noise factor, and sensitivity of Josephson mixers have been measured. Using a point contact junction at 13 GHz, a minimum detectable signal of -90 dbm/MHz (measured) and -105 dbm/MHz (corrected) was obtained. Superconducting, miniature microstrip resonators operating at 10 to 15 GHz have been constructed using vacuum-deposited lead on low-loss sintered alumina substrate. Unloaded Q's (at 14.3 GHz) as high as 200,000 and 500,000 have been measured at 4.2 and 1.8 K respectively. The vacuum deposition technique used would permit the simulataneous fabrication of large numbers of miniature multielement filters and preselectors with low insertion loss and good skirt rejection. (Author)
Microwave superconducting mixers operating at 10–13 GHz utilizing Josephson junctions have been investigated analytically and experimentally. Measurements on mixer sensitivity were carried out at 13 GHz using waveguide-mounted experimental point-contact Josephson junctions at 4.2 K. Results showed sensitivities of −90 dBm/MHz (10−18 W/Hz) which included mismatch losses encountered in the waveguide structure. The Josephson junction mixing mechanism was analyzed on the basis of small-signal modulation of the staircase like dc I-V characteristics. It was shown that a small-signal microwave excitation results in an ac lateral shift of the regions between steps, such that: (a) Optimum Josephson mixing occurs halfway between steps. (b) Mixing occurs between all steps with maximum conversion efficiency between the zero and first step. (c) Predicted low conversion loss and possibly internal gain for a matched mixer. The analytical model was simulated by a digital computer and the behavior of the Josephson mixer predicted for various conditions of excitation. The model chosen for the analysis and the computer simulation is based on the simplest assumptions concerning bulk-formed Josephson junctions. In the laboratory an external local oscillator set 60 MHz below the signal frequency was used to induce the well-known step structure in the dc I-V characteristic of the point-contact Josephson junction. Mixing of the Lo and signal was found to occur between constant voltage steps in agreement with both analysis and computer simulation. The correctness of the model is demonstrated by the agreement between the theory and experiment.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb–Nb point-contact junctions at 4.2 °K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1, 0.3, and 9.2 GHz. The point contact is in a nonresonant structure and fed by a constant current source: neither a strong rf coupling of the contact with a cavity nor a stabilizing shunt resistance was proved necessary. The direct observation of frequency conversion was performed with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1600 GHz. The experiments with intermediate frequencies fi of 0.1 and 0.3 GHz indicate that conventional frequency conversion does not occur but that the observed signals are related to noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. The results show that low-frequency current components are induced in the junction, which can give large spurious signals when small i.f. are used.
The Josephson frequency conversion in the millimeter and submillimeter wave region is studied with superconducting Nb-Nb point contact junctions at 4.2 K, using the contact both as the local oscillator and the mixer with intermediate frequencies of 0.1 and 9.2 GHz. Frequency conversion signals are only detected in the latter case with a microwave receiver at 9.2 GHz in a range of Josephson frequencies between 145 and 1 600 GHz. The experiments with intermediate frequency fi of 0.1 GHz indicate for this small value of f i that the observed signals are not related to frequency conversion but noise effects. An analysis of the frequency conversion mechanism in a Josephson junction operated as an oscillator-mixer is proposed which includes the noise effects and also the feedback effects induced in a junction driven by a constant current source. We have then investigated the noise properties up to 450 GHz of superconducting point-contacts using the junction as an oscillator-mixer where the Josephson current is mixed with harmonics of an externally applied signal. The emitted intermediate frequency is detected at 9.2 GHz and its linewidth is measured. In the very high frequency range the dc quasiparticle current dominates in a Josephson weak-link and we compare the corresponding theoretical linewidth calculated by Scalapino with our experimental results.
NOTE: Text or symbols not renderable in plain ASCII are indicated by [...]. Abstract is included in .pdf document. This thesis describes both theoretical and experimental investigations into the dynamics and noise processes of Josephson junctions, with the intent of evaluating their potential as mixers in heterodyne instruments for submillimeter-wave (i.e., the frequency range from 300 GHz to 3THz) detection. Superconducting tunnel junctions utilizing the nonlinearity due to photon-assisted tunneling of quasiparticles (SIS mixers) have become the state-of-the-art technology for sensitive heterodyne detection up to frequencies of about 700 [...]. Recent progress in the fabrication of high [...], superconductors has led to Josephson-effect devices with [...] products of up to ten millivolts, which might be suitable for mixing at frequencies of many terahertz. The key question for weighing the prospects for high-frequency Josephson mixers is that of the sensitivity which can be attained. Previous experimental work on Josephson mixing suggests the existence of an "excess" noise, which degrades the sensitivity. Theoretical modeling of mixer performance, based on the resistivelyshunted junction (RSJ) model for the dynamics of the device, also indicates the presence of larger noise than expected. The origin of this noise was not clearly understood, however, nor was its exact magnitude or expected scaling with frequency or junction characteristics known. In addition, previous experiments utilized crude devices of the point-contact type, which were unstable and thus undesirable for real applications. In the first part of this thesis research, extensive numerical simulations were performed with the RSJ model, including calculations of mixer noise and conversion efficiency. These calculations have revealed that the source of excess noise is the AC Josephson oscillations of the device, which can be completely incoherent, with a linewidth comparable to their frequency. Thus they appear as a broadband noise source. While this noise is intrinsic and unavoidable, an optimized mixer is still shown to be capable of interesting sensitivity levels, and the excess noise is expected to become relatively less important as the operating frequency is increased. Secondly, a process has been developed for the fabrication of stable, well-characterized, and reproducible Josephson devices based on resistively-shunted Nb and NbN tunnel junctions. The devices utilize submicron-area, high current-density tunnel junctions and a AuGe shunt resistor to yield completely non-hysteretic I-V curves, normal-state resistances of about [...] products of about half a millivolt. These devices should be nearly optimal for mixing at [...]. Heterodyne measurements using these junctions have been performed in a waveguide mixer mount. Receiver temperatures as low as 190 K (DSB), with -6 dB conversion efficiency, have been obtained at 100 [...], but these results are still a factor of about four higher than those predicted by the RSJ simulations. Accurate measurements of the available noise power of the junctions at the intermediate frequency of 1.5 [...] were made, and confirmed that the receivers were limited by elevated junction output noise. The deviations of the noise from theoretical predictions are shown to be caused by the nonlinear interaction of the junction with the embedding circuit. While this work points out some of the complexity introduced by the strong nonlinearity of Josephson devices, it is still expected that Josephson-effect mixers may be useful for heterodyne detection at very high frequencies.
We report the experimental evaluation of a high-temperature superconducting (HTS) Josephson mixer. The mixer is fabricated from a HTS step-edge junction on MgO substrate. The mixer device operates as a lower side-band down-converter from a radio frequency between 6 and 10 GHz to a 1-2 GHz intermediate frequency under the action of a local oscillator. The experimental results of the current-voltage characteristics, optimal bias conditions, dynamic range, linearity, conversion gain, and the temperature dependence of the mixer are presented.