This Thesis lies within the field of Slow and Fast Light (SFL) technologies, which are\n\t\t\t\t currently receiving much attention because of their interesting applications, ranging from\n\t\t\t\t optical information processing to enhanced precision sensing and interferometry. These\n\t\t\t\t technologies are based on systems that exhibit steep positive dispersion to propagate a light\n\t\t\t\t pulse at group velocity well below the speed of light in vacuum (slow light) or steep negative\n\t\t\t\t dispersion to achieve pulse propagation at superluminal or even at negative group velocity (fast\n\t\t\t\t light). SFL effects thus arise in a myriad of materials exhibiting spectral resonances. Current\n\t\t\t\t efforts in this field are mainly focused on the manipulation of material gain or absorption\n\t\t\t\t resonances by nonlinear optical processes (material SFL) or on the optimization of photonic\n\t\t\t\t band-gap structures, without substantial material dispersion, but where structural dispersion\n\t\t\t\t comes as a result of the coupling between the light wavelength and the characteristic length of\n\t\t\t\t the system (structural SFL).This Thesis focuses on the theoretical and experimental analysis of electromagnetic pulse\n\t\t\t\t propagation with abnormal group velocities in two kind of linear and passive devices. In the\n\t\t\t\t first part of the Thesis a new system exhibiting structural SFL is demonstrated. It deals with\n\t\t\t\t multiple-beam interferometers and provides a comprehensive study of the arising of SFL in\n\t\t\t\t this system devoid of photonic band gaps. A theoretical model that fully describes the allowed\n\t\t\t\t pulse propagation regimes and its performance in terms of both the interferometer’s and the\n\t\t\t\t pulse characteristics is developed. Considering amplitude modulated pulses, the capabilities\n\t\t\t\t and limitations of SFL effects in this kind of system are retrieved by quantifying typical figures\n\t\t\t\t of merit like fractional delay, pulse distortion and Delay-Bandwidth Product. The theoretical\n\t\t\t\t framework is valid for any frequency region and the model predictions are probed by performing experiments in the radiofrequency range and through exact numerical simulations in the optical\n\t\t\t\t range. The simplest interferometer, with only two branches, is first considered since it is widely\n\t\t\t\t used in actual communication systems. It is analytically demonstrated that slow light cannot\n\t\t\t\t possibly be sustained and that the total attenuation drives the changes in the pulse propagation\n\t\t\t\t regimes. By increasing the number of branches, group delay tuning from slow to fast light\n\t\t\t\t regimes occurs if the optical length of one of the branches is slightly changed.In the second part of the Thesis, the ability of mono- and multilayer structures to speed up\n\t\t\t\t or slow down electromagnetic pulses is investigated, with special emphasis on their reflection\n\t\t\t\t properties. Namely, Distributed Bragg Reflectors (DBRs) and Fabry-Perot filters, common in\n\t\t\t\t today’s communication systems, are examined. These structures were fabricated to operate\n\t\t\t\t in the microwave and in the radiofrequency range with the aim of confirming theoretical\n\t\t\t\t predictions. Experimental results of their frequency- and time-domain characterization are\n\t\t\t\t compared with simulations. An advantage of operating in these frequency ranges is that the\n\t\t\t\t transmission and reflection phase function can be measured with a two port vector network\n\t\t\t\t analyzer. Such a simple measurement of this key function that determines the pulse propagation\n\t\t\t\t regime cannot be directly performed in the optical range. Moreover, microstrip DBRs\n\t\t\t\t were designed and their potential application as a negative group-delay circuit to improve\n\t\t\t\t the efficiency of feedforward amplifiers, which are commonly used for cancelling inherent\n\t\t\t\t distortion in microwave amplifiers, is explored.
This Thesis lies within the field of Slow and Fast Light (SFL) technologies, which are\n\t\t\t\t currently receiving much attention because of their interesting applications, ranging from\n\t\t\t\t optical information processing to enhanced precision sensing and interferometry. These\n\t\t\t\t technologies are based on systems that exhibit steep positive dispersion to propagate a light\n\t\t\t\t pulse at group velocity well below the speed of light in vacuum (slow light) or steep negative\n\t\t\t\t dispersion to achieve pulse propagation at superluminal or even at negative group velocity (fast\n\t\t\t\t light). SFL effects thus arise in a myriad of materials exhibiting spectral resonances. Current\n\t\t\t\t efforts in this field are mainly focused on the manipulation of material gain or absorption\n\t\t\t\t resonances by nonlinear optical processes (material SFL) or on the optimization of photonic\n\t\t\t\t band-gap structures, without substantial material dispersion, but where structural dispersion\n\t\t\t\t comes as a result of the coupling between the light wavelength and the characteristic length of\n\t\t\t\t the system (structural SFL).This Thesis focuses on the theoretical and experimental analysis of electromagnetic pulse\n\t\t\t\t propagation with abnormal group velocities in two kind of linear and passive devices. In the\n\t\t\t\t first part of the Thesis a new system exhibiting structural SFL is demonstrated. It deals with\n\t\t\t\t multiple-beam interferometers and provides a comprehensive study of the arising of SFL in\n\t\t\t\t this system devoid of photonic band gaps. A theoretical model that fully describes the allowed\n\t\t\t\t pulse propagation regimes and its performance in terms of both the interferometer’s and the\n\t\t\t\t pulse characteristics is developed. Considering amplitude modulated pulses, the capabilities\n\t\t\t\t and limitations of SFL effects in this kind of system are retrieved by quantifying typical figures\n\t\t\t\t of merit like fractional delay, pulse distortion and Delay-Bandwidth Product. The theoretical\n\t\t\t\t framework is valid for any frequency region and the model predictions are probed by performing experiments in the radiofrequency range and through exact numerical simulations in the optical\n\t\t\t\t range. The simplest interferometer, with only two branches, is first considered since it is widely\n\t\t\t\t used in actual communication systems. It is analytically demonstrated that slow light cannot\n\t\t\t\t possibly be sustained and that the total attenuation drives the changes in the pulse propagation\n\t\t\t\t regimes. By increasing the number of branches, group delay tuning from slow to fast light\n\t\t\t\t regimes occurs if the optical length of one of the branches is slightly changed.In the second part of the Thesis, the ability of mono- and multilayer structures to speed up\n\t\t\t\t or slow down electromagnetic pulses is investigated, with special emphasis on their reflection\n\t\t\t\t properties. Namely, Distributed Bragg Reflectors (DBRs) and Fabry-Perot filters, common in\n\t\t\t\t today’s communication systems, are examined. These structures were fabricated to operate\n\t\t\t\t in the microwave and in the radiofrequency range with the aim of confirming theoretical\n\t\t\t\t predictions. Experimental results of their frequency- and time-domain characterization are\n\t\t\t\t compared with simulations. An advantage of operating in these frequency ranges is that the\n\t\t\t\t transmission and reflection phase function can be measured with a two port vector network\n\t\t\t\t analyzer. Such a simple measurement of this key function that determines the pulse propagation\n\t\t\t\t regime cannot be directly performed in the optical range. Moreover, microstrip DBRs\n\t\t\t\t were designed and their potential application as a negative group-delay circuit to improve\n\t\t\t\t the efficiency of feedforward amplifiers, which are commonly used for cancelling inherent\n\t\t\t\t distortion in microwave amplifiers, is explored.
We demonstrate the generation of slow and fast light (SFL) in a linear and passive three-beam interferometer. Such propagation regimes occur for narrowband pulses with center frequency close to the transmission minima. A model that fully describes SFL effects in this system is developed and an analytical approximate expression for the group delay at the minima is derived. We demonstrate that slow light is not possible if the length difference between adjacent branches of the interferometer is a constant. If a small length detuning ($\ensuremath{\xi}$) in one of the branches is introduced, slow light at one of the two minima can be obtained as long as $\ensuremath{\xi}$ exceeds a critical value. Simultaneously, tunneling, superluminal, or normal regime is sustained at the other minimum, depending on the system's length. A proof-of-model experiment is performed in the radiofrequency range using coaxial cables and $1\ifmmode\times\else\texttimes\fi{}3$ power splitters. The possible realization and performance of such a system in the optical range is also discussed. This system is proposed as a simple alternative to active systems and photonic band-gap structures for sustaining both slow and fast light.
The group velocity at which light pulses propagate through a dispersive material system is very different from the vacuum speed of light c, One refers to light as being "slow" for v g << c (Boyd & Gauthier, 2009) or "fast" for v g > c or v g <0 (Stenner et al, 2003 ).For v g <0, the pulse envelope appears to travel backward in the material (Gehring et al, 2006), and hence it is sometimes referred to as "backward light."The subject of slow light has caused keen interest in the past decade or more, and it is possible to control the group velocity of light pulses in the dispersive materials.Interest in slow and fast light dates back to the early days of the 20th century.Sommerfeld and Brillouin (Sommerfeld & Brillouin, 1960) were intrigued by the fact that theory predicts that v g can exceed c, which leads to apparent inconsistencies with Einstein's special theory of relativity.Experimental investigations of extreme propagation velocities were performed soon after the invention of the laser (Faxvog and et al, 1970).In 1999, Harris's group research work greatly stimulated researchers' interests, which showed that light could be slowed down to 17m/s.The result was obtained in ultra cold atom clouds with the use of electromagnetically induced transparency (EIT), which induces transparency in a material while allowing it to retain strong linear and nonlinear optical properties (Hau et al, 1999).Slow light can also be obtained through the use of the optical response of hot atomic vapors (Philips et al, 2001).These early research works require hard conditions and the slow light cannot operate in room temperature.Recently, researchers found ways to realize slow light operating in room temperature and solid-state materials, which are more suited for many practical applications, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.In this chapter, we describe some of the physical mechanisms that can be used to induce slow and fast light effects in room-temperature solids (Bigelow et al, 2003) and some of the exotic propagation effects that can thereby be observed.We also survey some applications of slow and fast light within the fields of quantum electronics and photonics. Fundamentals of slow and fast lightSlow and fast light refer to the group velocity of a light wave.The group velocity is the velocity most closely related to the velocity at which the peak of a light pulse moves through an optical dispersive material (Milonni, 2005), and is given by the standard result www.intechopen.comRecent Progress in Optical Fiber Research 82where n is the refractive (phase) index and ω is the angular frequency of the carrier wave of the light field.One refers to light as being slow light for v g << c, fast light for for v g > c, and backwards light for v g <0 or v g is negative.Extreme values of the group velocity invariably rely on the dominance of the second contribution to the group index of Equation ( 1).This contribution of course results from the frequency dependence of the refractive index, and for this reason extreme values of the group velocity are usually associated with the resonant or near-resonant response of material systems.According to this theory, slow light is expected in the wings of an absorption line and fast light is expected near line center, and the spatial dispersion, that is, the non-locality in space of the medium response, is another mechanism that can lead to slow light, as has been predicted (Kocharovskaya et al,2001) and observed (Strekalov et al, 2001).We catalogue the main methods to realize slow light in room temperature solid, namely slow light via stimulated Brillouin scattering(SBS), slow light via coherent population oscillations (CPO), tunable time delays based on group velocity dispersion or conversion/ dispersion(C/D), slow light in fiber Bragg gratings and so on.We will describe CPO and SBS slow light in more details.
Over the past few years, researchers have directed a significant amount of effort towards realizing tunable all-optical devices using nonlinear optical methods. It is now possible to exercise dynamic control of the group velocity of light traveling through a wide variety of material systems. The slow and fast light refer to situations in which the group velocity íg of an optical pulse through a dispersive material can be made to be smaller and larger, respectively, than the phase velocity vp = c/n. This ability could overcome the remaining challenge in current optical networks of storing and manipulating an optical signal directly in optical domain so as to avoid a bottleneck due to optical-to-electrical (O/E) and electrical-to-optical (E/O) conversions. The overall purpose of the dissertation is to study novel slow-light systems that provide controlled generation of large pulse delays relative to the pulse width with minimal pulse shape distortion by optimally design resonance profiles of such systems. The system design studies utilize several measures of performance such as the fractional delay, power throughput, and signal distortion under the limited system resource constraints. To this end, powerful data fidelity metrics are required to quantify the performance of tunable delay devices. Here, a new framework for measuring an information velocity and throughput is described and implemented using Shannon mutual information concepts. This new technique is used to investigate trends, trade-offs, and limits in slow light devices, which are physically sensible and in good agreement with analyses obtained using a conventional eye-opening(EO) metric. Using these information-theoretic and/or conventional metrics, we present the quantifying performance of gain-based stimulated Brillouin scattering (SBS) system in optical fibers as well as optical passive devices such as Fabry-Perot, fiber Bragg gratings, and ring resonators. It is shown that combining the SBS gain medium with these passive devices can compensate their respective disadvantages and thus increase delay performance without using additional resource of SBS pump power. The results show the possibility of achieving a fractional delay up to 10 at a signal bandwidth up to tens of GHz.
We propose and demonstrate a method for manipulation of group velocity from slow-to-fast light (SFL) in a two-beam Mach–Zehnder interferometer in radio frequency (RF) regime. The subluminal, superluminal, and tunneling propagation regimes occur in a narrow frequency band around the resonance frequency of the interferometer where destructive interference occurs. Importantly, the group velocity at the resonance frequency can be controlled by simply adjusting the transmission magnitude of the signals from the two beams, without changing the length of the interferometer. Models that fully describe the SFL effects in the microwave interferometer system are developed and closed-form expressions for the prediction of group delays at the resonance frequency are obtained. The simple and effective method is verified through numerical calculations and experimental measurements. We also demonstrate that the proposed method applies to a microwave cavity interferometer. A proof-of-concept experiment is performed using a custom open-ended coaxial cable resonator (OE-CCR). Positive and negative group delays are experimentally measured when the resonator is set at different coupling states.
In this work, we explore the generation of slow and fast light (SFL) in a linear and passive three-beam interferometer for center pulse frequency close to the transmission minima. We show that the group delay can be tuned from subluminal to superluminal values by simply changing the length of one of the interferometer's arms. Some figures of merit of this three-beam interferometer as an SFL system are discussed, namely fractional delay and pulse distortion. We build our interferometers using 50-Ω coaxial cables and 1x3 power splitters in order to perform the experiments in the radiofrequency range, where a full frequency-domain characterization of them can be performed with a vector network analyzer. Together with the frequency domain results, we present direct measurement of the group delay in time domain. Fractional delays of ±25% were measured for a train of sinusoidally modulated wavepacket with 300 kHz repetition rate. Additionally, a Lithium Niobate interferometer operative in the optical range (1.55 μm) was simulated and discussed. This system is proposed as an alternative to active systems and photonic band-gap structures for sustaining both slow and fast light, with special emphasis in sensing purposes.
Research into slow light began theoretically in 1880 with the paper [1] of H A Lorentz, who is best known for his work on relativity and the speed of light. Experimental work started some 60 years later with the work of S L McCall and E L Hahn [2] who explored non-linear self-induced transparency in ruby. This field of research has burgeoned in the last 10 years, starting with the work of L Vestergaard Hau and coworkers on slow light via electromagnetically induced transparency in a Bose–Einstein condensate [3]. Many groups are now able to slow light down to a few metres per second or even stop the motion of light entirely [4]. Today, slow light – or more often `slow and fast light' – has become its own vibrant field with a strongly increasing number of publications. In broad scope, slow light research can be categorized in terms of the sort of physical mechanism used to slow down the light. One sort of slow light makes use of material dispersion. This dispersion can be the natural dispersion of the ordinary refractive index or can be the frequency dependence of some nonlinear optical process, such as electromagnetically induced transparency, coherent population oscillations, stimulated light scattering, or four-wave mixing processes. The second sort of slow light makes use of the wavelength dependence of artificially structured materials, such as photonic crystals, optical waveguides, and collections of microresonators. Material systems in which slow light has been observed include metal vapours, rare-earth-doped materials, Raman and Brillioun gain media, photonic crystals, microresonators and, more recently, metamaterials. A common feature of all of these schemes is the presence of a sharp single resonance or multiple resonances produced by an atomic transition, a resonance in a photonic structure, or in a nonlinear optical process. Current applications of slow light include a series of attractive topics in optical information processing, such as optical data storage, optical memories, quantum information devices, and optical communication systems in which the use of slow light will allow all-optical processing with less wasted heat. To implement these applications, devices such as buffers, memories, interferometers and switches that utilize slow light need to be developed. Future challenges include the need for improved coupling of light into slow light modes, overcoming propagation losses, and mitigating the influence of large dispersion of the group velocity. The collection of papers in this special issue of Journal of Optics features a broad spectrum of articles that highlight actual developments in many of the material types and schemes described above. It represents therefore an excellent up to date snapshot of the current state of the field of slow light research. References [1] Lorentz H A 1880 Uber die Beziehung zwischen der Fortpflanzung des Lichtes und der Körperdichte Wiedemann Ann. 9 641–64 [2] McCall S L and Hahn E L 1967 Self-induced transparency by pulsed coherent light Phys. Rev. Lett. 18 908–11 [3] Vestergaard Hau L, Harris S E, Dutton Z and Behroozi C H 1999 Nature 397 594 [4] Philips D F, Fleischhauer A, Mair A, Walsworth R L and Lukin M D 2001 Storage of light in atomic vapor Phys. Rev. Lett. 86 783–6