Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

Development of Balanced SIS Mixers for ALMA Band-10

S. V. Shitov, Oleg V. Koryukin, Y. Uzawa, Takashi Noguchi, Andrey V. Uvarov, Ilya A. Cohn

Published May 1, 2006• 2 citations
OpenAlex

Abstract

down to only 2-3 p,W for a two polarized SIS receiver, if submicron SIS junctions are used in the balanced mixer configuration. There are a few options for waveguide balanced and sideband separating mixers employing the straightforward connection of the DSB mixers using hybrid couplers [2]. However, the low-loss operation of the waveguide-based connections and the required balancing of the mixers both are of a great concern in the THz frequency range. This is a good reason to look for the more compact design of the RF circuit for waveguide or/and consider an integrated quasioptical SIS mixer design. It is known that the conversion gain of a SIS junction is reducing essentially above the gap frequency, and it turns negligibly low above twice the gap frequency. The ALMA Band-10 DSB receiver specification for TRx is 230 K within 80% of the band 787-950 GHz and 345 K at any frequency of the band. The IF range of 4-12 GHz is required for the DSB receiver with ripples below 4 dB within each 2 GHz segment. All these make the accurate design of the mixer's RF and IF circuits very important. Since the Q-factor of a SIS junction at submillimeter wavelength is high (Q>>1), the twin-SIS junction [3]-[5] is a good solution providing about twice RF bandwidth of a single junction. However, it is known that two junctions in the twin-SIS are unequally coupled at RF across the band, thus providing less gain than one can expect from the equivalent junction of the same R. This effect is difficult to estimate experimentally, since two junctions are connected in parallel at DC. The growing importance of such accurate analysis in THz range can be motivated with concern of the essential drop of conversion gain of a Nb-based SIS mixer closer to 1 THz. To analyze the effect of unequal pump and dynamic resistance for a two-junction SIS mixer, the Tucker's 3-port model can be used yet being expanded to multi-junction mixing arrays. Abstract-A few concepts of a wide-band balanced SIS mixer employing submicron-sized SIS junctions are under development for 787-950 GHz frequency range. A quasioptical DSB balanced mixer with integrated cross-slot antenna is considered as the less laborious and cheaper option. The silicon lens-antenna beam efficiency is expected above 80 % across the whole band with first-order sidelobe below -16 dB. To use the conservative horn antenna solution, a singlechamber waveguide DSB balanced mixer is developed. Two equal probe-type SIS chips are inserted into a full-height waveguide through its opposite broad walls; these two mixers are driven by the signal waveguide in series. The LO current is transferred to the mixers in parallel via a capacitive probe inserted through the narrow wall of the signal waveguide from the neighboring LO waveguide. The HFSS model demonstrated the LO power coupling efficiency above -3 dB, almost perfect signal transfer and the LO cross talk below 30 dB that take into account misalignment (misbalance) of the chips. It is demonstrated numerically using Tucker's 3-port model that unequal pump of junctions of a twin-SIS mixer can lead, in spite of the perfect signal coupling, to degradation of the gain performance up to -3 dB, especially at the top of the ALMA Band-10.

Related papers

Design and Characterization of Two-Junction Tuning Circuits for Submillimeter SIS Mixers

Michael C. Gaidis, M. Bin, David A. B. Miller +3 more

We report on the continuing development of submillimeter quasi-optical slot antenna SIS mixers which use two-junction tuning circuits [1]. The mixers use 10 kA/cm2 Nb/Al-Oxide/Nb junctions and Nb wiring, and have generated DSB receiver noise temperatures around 5hv/kB to 700 GHz, and 16hv/kB (620 K) at 798 GHz. We present Fourier-transform spectrometer (FTS) measurements and heterodyne measurements on several such devices. In general, the measured response at frequencies below the gap of Nb is in good agreement with the predicted performance. Introduction SIS mixers with Nb-trilayer tunnel junctions offer excellent performance at frequencies below 800 GHz, and should perform competitively at frequencies as high as 1.4 THz [2-5]. Our goal is to develop a suite of ultra-low-noise SIS mixers which cover frequencies from = 400 GHz to more than I THz. At frequencies below the Nb gap (< 700 GHz), existing devices perform quite well [6], but further improvements in noise temperatures remain important. In addition, it is quite useful to be able to predict device performance given the design parameters. One can then optimize the device design for a particular frequency band, and confirm that we indeed understand the physics of the device. Progress in the design and operation of devices in this frequency range is presented below. At frequencies above the Nb gap, RF photons can break Cooper pairs, resulting in greater signal loss and higher receiver noise temperatures. The loss is particularly important in the slender microstrip lines used to resonate the junction capacitance and to transform the antenna impedance down to the RF junction impedance. However, the actual coupling of radiation into Nb junctions above the gap should still be reasonably efficient -more than 30% at 800 GHz [7]. In addition to RF loss, one is also affected by increased dispersion at frequencies near the gap. The Nb microstriplines have therefore been carefully designed to ensure the desired bandpass is achieved. We demonstrate for the first time that all-Nb SIS receivers can have substantially better performance than GaAs Schottky receivers for the astronomically important CI ( P2 — P 1 ) and CO (7-6) transitions near 810 GHz. Receiver Configuration Since waveguide mixers become difficult to construct at short submillimeter wavelengths, we have adopted a quasi-optical approach. Here, lenses take the place of waveguide horns, and the incoming radiation is collected by a planar antenna on the SIS mixer substrate [8]. This offers several other advantages, such as on-chip broad-band silt a SS 114 SSE WA Wa Sta MX Dewar 120 Mylar Window SIS Mixer 295 IQ 77 K Mylar Load Bearnsplitter ICI 1= NZ IC =1 HEN1T Amplifier Polyethylene Lens

•Mar 1, 1995•2 citations

Design and Development of SIS Mixers for ALMA Band 8

Wenlei Shan, Takashi Noguchi, S. C. Shi +1 more

In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).

IEEE Transactions on Applied Superconductivity•Jun 1, 2005•27 citations

A sensitive ALMA Band 10 SIS receiver engineering model

Yoshinori Uzawa, M. Kroug, Takafumi Kojima +7 more

We have developed a single polarization engineering model of the Atacama Large Millimeter/Submillimeter Array (ALMA) Band 10 (0.78–0.95 THz) receivers. The front-end optics comprises a pair of ellipsoidal mirrors and a corrugated feed horn. A waveguide mixer block is attached to the feed horn in which an NbTiN-based superconductor–insulator–superconductor (SIS) mixer chip, which uses a quartz substrate, is mounted onto a WR-1.2 full-height waveguide. The SIS mixer employs two Nb / AlO x / Nb junctions and an NbTiN/SiO 2 /Al microstrip tuning circuit. A very wide intermediate frequency (IF) system with a bandwidth of 4–12 GHz is employed. The receiver demonstrated double-sideband (DSB) noise temperatures of below 240 K at local oscillator (LO) frequencies ranging from 792 to 945 GHz, without any correction for loss in front of the receiver. The lowest DSB receiver noise temperature, 179 K, was obtained at the center frequency of the designed band, which corresponds to about 4 quanta. These results represent state-of-the-art sensitivity for a receiver at an operating physical temperature of 4 K.

Superconductor Science and Technology•Oct 19, 2009•22 citations

Study on SIS Mixers for "ALMA" Band-10

S. V. Shitov, Oleg V. Koryukin, Andrey V. Uvarov +7 more

This paper studies superconductor insulator superconductor (SIS) mixers for ALMA Band-10 project. The possible scheme of the ALMA Band-10 cartridge with balanced lens-antenna mixers is presented. The new balanced full-height waveguide SIS mixer comprises two equal mixer chips fabricated on quartz substrates. Each chip contains an RF circuit with hybrid twin-SIS junction NbTiN/Nb-AlOx-Nb/Al. The preliminary experimental study of Band-10 receiver with a double-slot antenna SIS mixer mounted with a 10-mm immersion silicon lens is done to define an optimum layout of the tuning circuit and a combination of materials leading to the best performance of the SIS mixer.

International Kharkiv Symposium on Physics and Engineering of Microwaves, Millimeter and Submillimeter Waves•Jun 1, 2007•0 citations

Low-noise integrated balanced SIS mixer for 787–950 GHz

Yasunori Fujii, Takafumi Kojima, Álvaro González +5 more

Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.

Superconductor Science and Technology•Nov 30, 2016•13 citations

275–500-GHz Wideband Waveguide SIS Mixers

Takafumi Kojima, M. Kroug, Álvaro González +5 more

We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.

IEEE Transactions on Terahertz Science and Technology•Oct 1, 2018•23 citations
down to only 2-3 p,W for a two polarized SIS receiver, if submicron SIS junctions are used in the balanced mixer configuration. There are a few options for waveguide balanced and sideband separating mixers employing the straightforward connection of the DSB mixers using hybrid couplers [2]. However, the low-loss operation of the waveguide-based connections and the required balancing of the mixers both are of a great concern in the THz frequency range. This is a good reason to look for the more compact design of the RF circuit for waveguide or/and consider an integrated quasioptical SIS mixer design. It is known that the conversion gain of a SIS junction is reducing essentially above the gap frequency, and it turns negligibly low above twice the gap frequency. The ALMA Band-10 DSB receiver specification for TRx is 230 K within 80% of the band 787-950 GHz and 345 K at any frequency of the band. The IF range of 4-12 GHz is required for the DSB receiver with ripples below 4 dB within each 2 GHz segment. All these make the accurate design of the mixer's RF and IF circuits very important. Since the Q-factor of a SIS junction at submillimeter wavelength is high (Q>>1), the twin-SIS junction [3]-[5] is a good solution providing about twice RF bandwidth of a single junction. However, it is known that two junctions in the twin-SIS are unequally coupled at RF across the band, thus providing less gain than one can expect from the equivalent junction of the same R. This effect is difficult to estimate experimentally, since two junctions are connected in parallel at DC. The growing importance of such accurate analysis in THz range can be motivated with concern of the essential drop of conversion gain of a Nb-based SIS mixer closer to 1 THz. To analyze the effect of unequal pump and dynamic resistance for a two-junction SIS mixer, the Tucker's 3-port model can be used yet being expanded to multi-junction mixing arrays. Abstract-A few concepts of a wide-band balanced SIS mixer employing submicron-sized SIS junctions are under development for 787-950 GHz frequency range. A quasioptical DSB balanced mixer with integrated cross-slot antenna is considered as the less laborious and cheaper option. The silicon lens-antenna beam efficiency is expected above 80 % across the whole band with first-order sidelobe below -16 dB. To use the conservative horn antenna solution, a singlechamber waveguide DSB balanced mixer is developed. Two equal probe-type SIS chips are inserted into a full-height waveguide through its opposite broad walls; these two mixers are driven by the signal waveguide in series. The LO current is transferred to the mixers in parallel via a capacitive probe inserted through the narrow wall of the signal waveguide from the neighboring LO waveguide. The HFSS model demonstrated the LO power coupling efficiency above -3 dB, almost perfect signal transfer and the LO cross talk below 30 dB that take into account misalignment (misbalance) of the chips. It is demonstrated numerically using Tucker's 3-port model that unequal pump of junctions of a twin-SIS mixer can lead, in spite of the perfect signal coupling, to degradation of the gain performance up to -3 dB, especially at the top of the ALMA Band-10.
We report on the continuing development of submillimeter quasi-optical slot antenna SIS mixers which use two-junction tuning circuits [1]. The mixers use 10 kA/cm2 Nb/Al-Oxide/Nb junctions and Nb wiring, and have generated DSB receiver noise temperatures around 5hv/kB to 700 GHz, and 16hv/kB (620 K) at 798 GHz. We present Fourier-transform spectrometer (FTS) measurements and heterodyne measurements on several such devices. In general, the measured response at frequencies below the gap of Nb is in good agreement with the predicted performance. Introduction SIS mixers with Nb-trilayer tunnel junctions offer excellent performance at frequencies below 800 GHz, and should perform competitively at frequencies as high as 1.4 THz [2-5]. Our goal is to develop a suite of ultra-low-noise SIS mixers which cover frequencies from = 400 GHz to more than I THz. At frequencies below the Nb gap (< 700 GHz), existing devices perform quite well [6], but further improvements in noise temperatures remain important. In addition, it is quite useful to be able to predict device performance given the design parameters. One can then optimize the device design for a particular frequency band, and confirm that we indeed understand the physics of the device. Progress in the design and operation of devices in this frequency range is presented below. At frequencies above the Nb gap, RF photons can break Cooper pairs, resulting in greater signal loss and higher receiver noise temperatures. The loss is particularly important in the slender microstrip lines used to resonate the junction capacitance and to transform the antenna impedance down to the RF junction impedance. However, the actual coupling of radiation into Nb junctions above the gap should still be reasonably efficient -more than 30% at 800 GHz [7]. In addition to RF loss, one is also affected by increased dispersion at frequencies near the gap. The Nb microstriplines have therefore been carefully designed to ensure the desired bandpass is achieved. We demonstrate for the first time that all-Nb SIS receivers can have substantially better performance than GaAs Schottky receivers for the astronomically important CI ( P2 — P 1 ) and CO (7-6) transitions near 810 GHz. Receiver Configuration Since waveguide mixers become difficult to construct at short submillimeter wavelengths, we have adopted a quasi-optical approach. Here, lenses take the place of waveguide horns, and the incoming radiation is collected by a planar antenna on the SIS mixer substrate [8]. This offers several other advantages, such as on-chip broad-band silt a SS 114 SSE WA Wa Sta MX Dewar 120 Mylar Window SIS Mixer 295 IQ 77 K Mylar Load Bearnsplitter ICI 1= NZ IC =1 HEN1T Amplifier Polyethylene Lens
In this paper, we report on the design and experimental results of a fix-tuned Superconductor-Insulator-Superconductor (SIS) mixer for Atacama Large Millimeter/submillimeter Array (ALMA) band 8 (385-500 GHz) receivers. Nb-based SIS junctions of a current density of 10 kA/cm/sup 2/ and one micrometer size (fabricated with a two-step lift-off process) are employed to accomplish the ALMA receiver specification, which requires wide frequency coverage as well as low noise temperature. Parallel-connected twin junctions (PCTJ) are designed to resonate at the band center to tune out the junction geometric capacitance. A waveguide-microstrip probe is optimized to have nearly frequency-independent impedance at the probe's feed point, thereby making it much easier to match the low-impedance PCTJ over a wide frequency band. In addition, a superconducting magnet fixed onto the compact mixer block to provide efficient magnetic field coupling is designed. The SIS mixer demonstrates a minimum double-sideband receiver noise temperature of 108 K at the band center and temperatures of less than 167 K over the whole band (for an intermediate-frequency range of 4-8 GHz).
We have developed a single polarization engineering model of the Atacama Large Millimeter/Submillimeter Array (ALMA) Band 10 (0.78–0.95 THz) receivers. The front-end optics comprises a pair of ellipsoidal mirrors and a corrugated feed horn. A waveguide mixer block is attached to the feed horn in which an NbTiN-based superconductor–insulator–superconductor (SIS) mixer chip, which uses a quartz substrate, is mounted onto a WR-1.2 full-height waveguide. The SIS mixer employs two Nb / AlO x / Nb junctions and an NbTiN/SiO 2 /Al microstrip tuning circuit. A very wide intermediate frequency (IF) system with a bandwidth of 4–12 GHz is employed. The receiver demonstrated double-sideband (DSB) noise temperatures of below 240 K at local oscillator (LO) frequencies ranging from 792 to 945 GHz, without any correction for loss in front of the receiver. The lowest DSB receiver noise temperature, 179 K, was obtained at the center frequency of the designed band, which corresponds to about 4 quanta. These results represent state-of-the-art sensitivity for a receiver at an operating physical temperature of 4 K.
This paper studies superconductor insulator superconductor (SIS) mixers for ALMA Band-10 project. The possible scheme of the ALMA Band-10 cartridge with balanced lens-antenna mixers is presented. The new balanced full-height waveguide SIS mixer comprises two equal mixer chips fabricated on quartz substrates. Each chip contains an RF circuit with hybrid twin-SIS junction NbTiN/Nb-AlOx-Nb/Al. The preliminary experimental study of Band-10 receiver with a double-slot antenna SIS mixer mounted with a 10-mm immersion silicon lens is done to define an optimum layout of the tuning circuit and a combination of materials leading to the best performance of the SIS mixer.
Abstract We developed a low-noise, compact, balanced superconductor–insulator–superconductor (SIS) mixer, operating in the 787–950 GHz radio frequency range. A waveguide mixer block was designed to integrate all the key components, such as a radio frequency (RF) 90° hybrid coupler, two identical SIS mixer chips, bias-tees, and an intermediate frequency power-combiner. The RF waveguide 90° hybrid coupler consists of branch lines with wide slots optimized by numerical simulation, for ease of fabrication. The balanced mixer was installed into a cartridge type receiver, originally developed for the Atacama Large Millimeter/submillimeter Array Band 10 (787–950 GHz). The receiver demonstrated double sideband noise temperatures of approximately 200 K for most of the band, without any correction for loss in front of the receiver. The local oscillator noise rejection ratio was estimated to be more than 15 dB within the measured frequency range.
We have successfully demonstrated low-noise and wideband SIS mixers for the 275-500-GHz radio-frequency (RF) band, aiming to cover Atacama Large Millimeter/submillimeter Array band 7 (275-373 GHz) and band 8 (385-500 GHz) simultaneously. The waveguide SIS mixers integrate a multisection impedance transformer with a parallel-connected-twin-junction or single-junction circuits based on Nb/AlN/Nb trilayers with a critical current density of 31 kA/cm2. In order to achieve the targeted broadband performance, we designed an asymmetric one-side waveguide probe placed across a reduced height waveguide with dimensions 100 μm × 580 μm. The shape of the waveguide probe was optimized to have nearly constant impedance at around 35 Ω in the desired RF range. For evaluation of the receiver performance, we have established a dual-band noise temperature measurement system. The system implements a broadband corrugated horn antenna and a 15-dB RF/local oscillator (LO) waveguide coupler based on WR-2.3 (290 μm × 580 μm) waveguide size. The target bandwidth is too wide for typical LO sources at these high frequencies, and, therefore, we applied a dual-band LO injection system utilizing two different LO sources and an LO diplexer. The IF chain uses a cryogenic isolator and a low-noise amplifier with a typical noise temperature of 2.1 K over the 4-8-GHz range. The measured double sideband receiver noise temperature is two to three times the quantum noise at all LO frequencies for both the twin-junction and the single-junction circuits.