Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2611.06761

Near-Quantum-Limited Readout for the Princeton Axion Search using a sub-GHz Kinetic Inductance Traveling Wave Parametric Amplifier

Joe Wiedemann, Roman Kolevatov, Jianyang Fu, J. Begin, Nate Otto, Félix St-Amour, Lyman Page, Henry LeDuc, Peter Day, Saptarshi Chaudhuri

Published Nov 4, 2026• 0 citations
arXivHTMLPDF

Abstract

Parametric amplifiers are a workhorse for near-quantum-limited measurements above 1 GHz. However, amplifier development has been more limited below 1 GHz. We present a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) operating over 300-700 MHz, with gain exceeding 30 dB and pump powers of a few hundred nanowatts. The system noise performance, as measured by a variable-temperature noise source, is 2.5-3.5 quanta. This device is a versatile new tool for precision measurements of sub-GHz signals, with applications including readout of semiconductor spin qubits, superconducting detector arrays, and searches for new physics beyond the Standard Model. We characterize aspects of the amplifier performance relevant to axion searches, including gain drift, compression point, amplifier noise at various operating temperatures, readout with an input circulator, and magnetic field insensitivity.

DOI
10.48550/arxiv.2611.06761

Related papers

A 4–8 GHz kinetic inductance traveling-wave parametric amplifier using four-wave mixing with near quantum-limited noise performance

Farzad Faramarzi, Ryan Stephenson, Sasha Sypkens +3 more

Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.

arXiv:2402.11751•APL Quantum•Jul 11, 2024•32 citations

Kinetic inductance traveling-wave parametric amplifiers near the quantum limit: Methodology and characterization

Logan A. Howe, Andrea Giachero, Michael R. Vissers +7 more

We present a detailed simulation and design framework for realizing traveling wave parametric amplifiers (TWPAs) using the nonlinear kinetic inductance of disordered superconductors -- in our case niobium-titanium-nitride (NbTiN). These kinetic inductance TWPAs (KITs) operate via three-wave mixing (3WM) to achieve high broadband gain and near-quantum-limited (nQL) noise. Representative fabricated devices -- realized using an inverted microstrip (IMS), dispersion-engineered, artificial transmission line -- demonstrate power gains above 25 dB, bandwidths beyond 3 GHz, and achieve ultimate system noise levels of 1.1 quanta even when operated with no magnetic shielding. These performance metrics are competitive with state-of-the-art Josephson-junction-based TWPAs but involve simpler fabrication and able to providing three orders of magnitude higher dynamic range ($IIP_1 = -68$ dBm, $IIP_3 = -55$ dBm), and high magnetic field resilience -- making KITs an attractive technology for highly multiplexed readout of quantum information and superconducting detector systems.

arXiv:2507.07706•Physical Review Applied•Feb 3, 2026•6 citations

A K-band Kinetic Inductance Parametric Amplifier Near the Quantum Limit

Chaofan Wang, Shihan Liu, Yufeng Wu +4 more

Advancing superconducting quantum devices to higher operating frequencies broadens their functionality and enables operation at elevated temperatures, but it also requires near-quantum-limited amplifiers beyond the few-gigahertz regime. Here we present a junction-free, kinetic-inductance parametric amplifier based on thin-film niobium nitride (NbN) operating at 23 GHz in the microwave K-band, achieving a gain up to 40 dB, a 100 MHz gain-bandwidth product, a 1 dB saturation input power of -85 dBm with 23 dB gain, and added noise no greater than 1.4 quanta for phase-preserving amplification. Leveraging the large superconducting gap of NbN, this architecture can be extended to even higher frequencies, supporting applications such as high-fidelity readout of millimeter-wave superconducting qubits and axion searches over an expanded mass window.

quant-pharXiv:2606.08406•Jun 9, 2026•1 citation

Temperature and magnetic field limits of a kinetic inductance traveling-wave parametric amplifier

Lucas M. Janssen, Farzad Faramarzi, Henry George LeDuc +5 more

Kinetic-inductance traveling-wave parametric amplifiers (KI-TWPAs) offer broadband near-quantum-limited amplification with high saturation power. Due to the high critical magnetic fields of high-kinetic-inductance materials, KI-TWPAs should be resilient to magnetic fields. In this work, we study how magnetic field and temperature affect the performance of a KI-TWPA based on a thin-NbTiN inverse microstrip with a Nb ground plane. This KI-TWPA can provide substantial signal-to-noise ratio improvement ($ΔSNR$) up to in-plane magnetic fields of 0.35T and out-of-plane fields of 50mT, considerably higher than what has been demonstrated with TWPAs based on Josephson junctions. The field compatibility can be further improved by incorporating vortex traps and by using materials with higher critical fields. We also find that the gain does not degrade when the temperature is raised to 3K (limited by the Nb ground plane) while $ΔSNR$ decreases with temperature consistently with expectation. This demonstrates that KI-TWPAs can be used in experiments that need to be performed at relatively high temperatures. The operability of KI-TWPAs in high magnetic field opens the door to a wide range of applications in spin qubits, spin ensembles, topological qubits, low-power NMR, and the search for axion dark matter.

arXiv:2509.15043•Physical Review Applied•May 13, 2026•2 citations

Near-quantum-limited subgigahertz Ti N kinetic inductance traveling-wave parametric amplifier operating in a frequency-translating mode

Farzad Faramarzi, Sasha Sypkens, Ryan Stephenson +4 more

We present the design and experimental characterization of a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) for subgigahertz frequencies. KI-TWPAs amplify signals through mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here uses a compactly meandered $\mathrm{Ti}\mathrm{N}$ microstrip transmission line to achieve the length needed to amplify subgigahertz signals. It is operated in a frequency-translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5 GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850 MHz. Using $\mathrm{Ti}\mathrm{N}$ as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to $\mathrm{Nb}\mathrm{Ti}\mathrm{N}$, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.

arXiv:2406.00530•Physical Review Applied•Feb 25, 2025•8 citations

A K-band kinetic-inductance parametric amplifier near the quantum limit

C.R. Wang, Shihan Liu, Yufeng Wu +4 more

Advancing superconducting quantum devices to higher operating frequencies broadens their functionality and enables operation at elevated temperatures, but it also requires near-quantum-limited amplifiers beyond the few-gigahertz regime. Here, we present a junction-free, kinetic-inductance parametric amplifier based on thin-film niobium nitride (NbN) operating at 23 GHz in the microwave K-band, achieving a gain up to 40 dB, a 100 MHz gain–bandwidth product, a 1 dB saturation input power of −85 dBm with 23 dB gain, and added noise not greater than 1.4 quanta for phase-preserving amplification. Leveraging the large superconducting gap of NbN, this architecture can be extended to even higher frequencies, supporting applications such as high-fidelity readout of millimeter-wave superconducting qubits and axion searches over an expanded mass window.

Applied Physics Letters•Jun 22, 2026•0 citations
Parametric amplifiers are a workhorse for near-quantum-limited measurements above 1 GHz. However, amplifier development has been more limited below 1 GHz. We present a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) operating over 300-700 MHz, with gain exceeding 30 dB and pump powers of a few hundred nanowatts. The system noise performance, as measured by a variable-temperature noise source, is 2.5-3.5 quanta. This device is a versatile new tool for precision measurements of sub-GHz signals, with applications including readout of semiconductor spin qubits, superconducting detector arrays, and searches for new physics beyond the Standard Model. We characterize aspects of the amplifier performance relevant to axion searches, including gain drift, compression point, amplifier noise at various operating temperatures, readout with an input circulator, and magnetic field insensitivity.
Kinetic inductance traveling-wave parametric amplifiers (KI-TWPAs) have a wide instantaneous bandwidth with a near quantum-limited noise performance and a relatively high dynamic range. Because of this, they are suitable readout devices for cryogenic detectors and superconducting qubits and have a variety of applications in quantum sensing. This work discusses the design, fabrication, and performance of a KI-TWPA based on four-wave mixing in a NbTiN microstrip transmission line. This device amplifies a signal band from 4 to 8 GHz without contamination from image tones, which are produced in a separate higher frequency band. The 4–8 GHz band is commonly used to read out cryogenic detectors, such as microwave kinetic inductance detectors and Josephson junction-based qubits. We report a measured maximum gain of over 20 dB using four-wave mixing with a 1 dB gain compression point of −58 dBm at 15 dB of gain over that band. The bandwidth and peak gain are tunable by adjusting the pump-tone frequency and power. Using a Y-factor method, we measure an amplifier-added noise of 0.5 ≤ Nadded ≤ 1.5 photons from 4.5 to 8 GHz.
We present a detailed simulation and design framework for realizing traveling wave parametric amplifiers (TWPAs) using the nonlinear kinetic inductance of disordered superconductors -- in our case niobium-titanium-nitride (NbTiN). These kinetic inductance TWPAs (KITs) operate via three-wave mixing (3WM) to achieve high broadband gain and near-quantum-limited (nQL) noise. Representative fabricated devices -- realized using an inverted microstrip (IMS), dispersion-engineered, artificial transmission line -- demonstrate power gains above 25 dB, bandwidths beyond 3 GHz, and achieve ultimate system noise levels of 1.1 quanta even when operated with no magnetic shielding. These performance metrics are competitive with state-of-the-art Josephson-junction-based TWPAs but involve simpler fabrication and able to providing three orders of magnitude higher dynamic range (IIP1=−68IIP_1 = -68IIP1​=−68 dBm, IIP3=−55IIP_3 = -55IIP3​=−55 dBm), and high magnetic field resilience -- making KITs an attractive technology for highly multiplexed readout of quantum information and superconducting detector systems.
Advancing superconducting quantum devices to higher operating frequencies broadens their functionality and enables operation at elevated temperatures, but it also requires near-quantum-limited amplifiers beyond the few-gigahertz regime. Here we present a junction-free, kinetic-inductance parametric amplifier based on thin-film niobium nitride (NbN) operating at 23 GHz in the microwave K-band, achieving a gain up to 40 dB, a 100 MHz gain-bandwidth product, a 1 dB saturation input power of -85 dBm with 23 dB gain, and added noise no greater than 1.4 quanta for phase-preserving amplification. Leveraging the large superconducting gap of NbN, this architecture can be extended to even higher frequencies, supporting applications such as high-fidelity readout of millimeter-wave superconducting qubits and axion searches over an expanded mass window.
Kinetic-inductance traveling-wave parametric amplifiers (KI-TWPAs) offer broadband near-quantum-limited amplification with high saturation power. Due to the high critical magnetic fields of high-kinetic-inductance materials, KI-TWPAs should be resilient to magnetic fields. In this work, we study how magnetic field and temperature affect the performance of a KI-TWPA based on a thin-NbTiN inverse microstrip with a Nb ground plane. This KI-TWPA can provide substantial signal-to-noise ratio improvement (ΔSNRΔSNRΔSNR) up to in-plane magnetic fields of 0.35T and out-of-plane fields of 50mT, considerably higher than what has been demonstrated with TWPAs based on Josephson junctions. The field compatibility can be further improved by incorporating vortex traps and by using materials with higher critical fields. We also find that the gain does not degrade when the temperature is raised to 3K (limited by the Nb ground plane) while ΔSNRΔSNRΔSNR decreases with temperature consistently with expectation. This demonstrates that KI-TWPAs can be used in experiments that need to be performed at relatively high temperatures. The operability of KI-TWPAs in high magnetic field opens the door to a wide range of applications in spin qubits, spin ensembles, topological qubits, low-power NMR, and the search for axion dark matter.
We present the design and experimental characterization of a kinetic inductance traveling-wave parametric amplifier (KI-TWPA) for subgigahertz frequencies. KI-TWPAs amplify signals through mixing processes supported by the nonlinear kinetic inductance of a superconducting transmission line. The device described here uses a compactly meandered TiN\mathrm{Ti}\mathrm{N}TiN microstrip transmission line to achieve the length needed to amplify subgigahertz signals. It is operated in a frequency-translating mode where the amplified signal tone is terminated at the output of the amplifier, and the idler tone at approximately 2.5 GHz is brought out of the cryostat. By varying the pump frequency, a gain of up to 22 dB was achieved in a tunable range from about 450 to 850 MHz. Using TiN\mathrm{Ti}\mathrm{N}TiN as the nonlinear element allows for a reduction of the required pump power by roughly an order of magnitude relative to NbTiN\mathrm{Nb}\mathrm{Ti}\mathrm{N}NbTiN, which has been used for previous KI-TWPA implementations. This amplifier has the potential to enable high-sensitivity and high-speed measurements in a wide range of applications, such as quantum computing, astrophysics, and dark matter detection.
Advancing superconducting quantum devices to higher operating frequencies broadens their functionality and enables operation at elevated temperatures, but it also requires near-quantum-limited amplifiers beyond the few-gigahertz regime. Here, we present a junction-free, kinetic-inductance parametric amplifier based on thin-film niobium nitride (NbN) operating at 23 GHz in the microwave K-band, achieving a gain up to 40 dB, a 100 MHz gain–bandwidth product, a 1 dB saturation input power of −85 dBm with 23 dB gain, and added noise not greater than 1.4 quanta for phase-preserving amplification. Leveraging the large superconducting gap of NbN, this architecture can be extended to even higher frequencies, supporting applications such as high-fidelity readout of millimeter-wave superconducting qubits and axion searches over an expanded mass window.