Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2607.14559

Dispersive Readout of a SiMOS Quantum Dot Using a Flip-Chip Integrated Microwave Resonator

Vo Kim Hieu Van, Santiago Serrano, Cédric Bohémier, Ajit Dash, Fay E. Hudson, Tuomo Tanttu, Chih Hwan Yang, MengKe Feng, Ensar Vahapoglu, Florian K. Unseld, Wee Han Lim, Andrea Morello, Andrew S. Dzurak, K. W. Chan

Published Jul 16, 2026• 1 citation
arXivHTMLPDF

Abstract

Heterogeneous integration provides a promising route to combine semiconductor quantum dot devices and superconducting microwave circuits, while allowing each component to be fabricated using an optimized process flow. Here, we demonstrate a flip-chip integrated platform for dispersive readout of silicon metal-oxide semiconductor (SiMOS) quantum dot devices. A SiMOS double quantum dot chip is bonded to a superconducting aluminum resonator chip using indium bump interconnects to enable microwave coupling to the quantum dot gate. We show that the developed flip-chip process is compatible with cryogenic operation of both the SiMOS device and the superconducting resonator, and demonstrate resonator-based detection of charge transitions in the quantum dot system. The readout signal-to-noise ratio follows a dependence of $\sqrt{t}$ with the integration time, reaching SNR = 1 at an integration time of approximately 0.3 ms. These results establish flip-chip bonding as a viable integration approach for SiMOS quantum dot devices operating at both dc and microwave frequencies, with potential applications for resonator-based techniques such as spin-photon coupling.

DOI
10.48550/arxiv.2607.14559

Related papers

Development of a Silicon Semiconductor Quantum Dot Qubit with Dispersive Microwave Readout

Edward Henry

Semiconductor quantum dots in silicon demonstrate exceptionally long spin lifetimes as qubits and are therefore promising candidates for quantum information processing. However, control and readout techniques for these devices have thus far employed low frequency electrons, in contrast to high speed temperature readout techniques used in other qubit architectures, and coupling between multiple quantum dot qubits has not been satisfactorily addressed.This dissertation presents the design and characterization of a semiconductor charge qubit based on double quantum dot in silicon with an integrated microwave resonator for control and readout. The 6 GHz resonator is designed to achieve strong coupling with the quantum dot qubit, allowing the use of circuit QED control and readout techniques which have not previously been applicable to semiconductor qubits. To achieve this coupling, this document demonstrates successful operation of a novel silicon double quantum dot design with a single active metallic layer and a coplanar stripline resonator with a bias tee for dc excitation.Experiments presented here demonstrate quantum localization and measurement of both electrons on the quantum dot and photons in the resonator. Further, it is shown that the resonator-qubit coupling in these devices is sufficient to reach the strong coupling regime of circuit QED. The details of a measurement setup capable of performing simultaneous low noise measurements of the resonator and quantum dot structure are also presented here.The ultimate aim of this research is to integrate the long coherence times observed in electron spins in silicon with the sophisticated readout architectures available in circuit QED based quantum information systems. This would allow superconducting qubits to be coupled directly to semiconductor qubits to create hybrid quantum systems with separate quantum memory and processing components.

•Jan 1, 2013•0 citations

3D integration of a hybrid quantum dot circuit-QED device for fast gate dispersive charge readout and coherent spin-photon coupling

Sebastien Granel, F. Gustavo, Jean-Luc Thomassin +8 more

Hybrid circuit quantum electrodynamics (cQED) aims at coupling various quantum degrees of freedom, among which are spin and charge degrees of freedom in gate defined quantum dots, phonons or magnons... with quantized electromagnetic fields in superconducting microwave cavities to investigate fundamental physics questions or for quantum computation and simulation. However, low microwave losses, key for many hybrid cQED experiments, are challenging to achieve given the often exotic and/or complex material stacks (e.g. semiconducting material, ferromagnets, or piezoelectric materials) required to host the various quantum degrees of freedom. In this work, we present a 3D-integration process to overcome this challenge for semi-industrial silicon MOS spin qubits. The process is based on dense indium bump interconnects at a pitch of 10 $\mathrmμ$m and superconducting thin films of Niobium Nitride (NbN). First, we report on DC and RF interconnect properties that demonstrate a high galvanic interconnection yield and internal quality factors above $10^{5}$ in the single photon regime for NbN resonators interrupted by a single indium bump interconnect. Eventually, we fabricated a 3D-integrated hybrid circuit quantum electrodynamics (cQED) device based on a semi-industrial MOS hole double quantum dot and a high impedance NbN resonator. For this device, we report a cavity internal quality factor above 10000 and demonstrate record sensitivity for gate-based dispersive readout of the charge degree of freedom with an SNR of 100 in 300 ns. Finally, we demonstrate strong spin-photon coupling of $g_{s}/2π$ = 75 MHz, which highlights the viability of 3D-integration for quantum dot based hybrid spin circuit quantum electrodynamics and opens to high-fidelity spin readout and microwave photon-based remote spin qubit entanglement.

arXiv:2604.25871•Physical Review Applied•Nov 3, 2026•2 citations

Multimodule microwave assembly for fast readout and charge-noise characterization of silicon quantum dots

Felix-Ekkehard von Horstig, David J. Ibberson, Giovanni A. Oakes +7 more

Fast measurements of quantum devices is useful in areas such as quantum sensing, quantum computing, and nanodevice quality analysis. Here, we develop a superconductor-semiconductor multimodule microwave assembly to demonstrate charge-state readout at the state of the art. The assembly consist of a superconducting readout resonator interfaced to a silicon-on-insulator (SOI) chiplet containing quantum dots (QDs) in a high- κ nanowire transistor. The superconducting chiplet contains resonant and coupling elements as well as L C filters that, when interfaced with the silicon chip, result in a resonant frequency f = 2.12 GHz, a loaded quality factor Q = 850 , and a resonator impedance Z = 470 Ω . Combined with the large gate lever arms of SOI technology, we achieve a minimum integration time for single and double QD transitions of 2.77 and 13.5 ns, respectively. We utilize the assembly to measure charge noise over 9 decades of frequency up to 500 kHz and find a 1 / f dependence across the whole frequency spectrum as well as a charge-noise level of 4 μ eV / Hz at 1 Hz. The modular microwave circuitry presented here can be directly utilized in conjunction with other quantum devices to improve the readout performance as well as enable large bandwidth noise spectroscopy, all without the complexity of superconductor-semiconductor monolithic fabrication. Published by the American Physical Society 2024

arXiv:2304.13442•Physical Review Applied•Apr 8, 2024•17 citations

Flip-Chip-Based Fast Inductive Parity Readout of a Planar Superconducting Island

Manuel Hinderling, Sofieke C. ten Kate, D. Z. Haxell +8 more

The properties of superconducting devices depend sensitively on the parity (even or odd) of the quasiparticles that they contain. Encoding quantum information in the parity degree of freedom is central in several emerging solid-state qubit architectures, including in hybrid superconductor-semiconductor devices. In the latter case, accurate, nondestructive, and time-resolved parity measurements are a challenging issue. Here, we report on control and real-time parity measurement in a superconducting island embedded in a superconducting loop and realized in a hybrid two-dimensional heterostructure using a microwave resonator. To avoid microwave losses impeding time-resolved measurements, the device and readout resonator are located on separate chips, connected via flip-chip bonding, and couple inductively through vacuum. The superconducting resonator detects the parity-dependent circuit inductance, allowing for fast parity readout. We have resolved even- and odd-parity states with a signal-to-noise ratio of SNR ≈ 3 for an integration time of 20 μ s and a detection fidelity exceeding 98 % . The real-time parity measurement shows a state lifetime extending into the millisecond range. Our approach will lead to a better understanding of coherence-limiting mechanisms in superconducting quantum hardware and help to advance inductive-readout schemes for hybrid qubits. Published by the American Physical Society 2024

arXiv:2307.06718•PRX Quantum•Aug 20, 2024•11 citations

Fast Readout in Semiconductor Quantum Dots

Wilson, Tim J

The need for fast readout to measure the state of a quantum dot device has important applications in the capabilities of using them as a means for quantum information processing. Traditional charge sensors used to readout the charge state of a quantum dot device are very robust and sensitive electrometers that have been in use since the late 1980s. They pose an issue to the future of quantum dots as a viable means of quantum computing, and that is in their slow acquisition times of the charge state of the quantum dot. This rate of measurement means that implementing any quantum error correction scheme becomes very difficult or even unfeasible as the coherence times of these semiconductor systems is short compared to charge sensor’s acquisition times. A possibility to speed up the measurement process of the charge state is possible thanks to the atomic molecular and optical (AMO) physics community.Cavity quantum electrodynamics (CQED) is the study of light-matter interactions when both the light and matter are taken to be quantized. A photon may interact with an atom via a dipole interaction to excite it from its ground state to its excited state, and the reverse can occur where the atom emits a photon and decays from its excited state ii to the ground state. This fundamental interaction which has been extensively studied in the AMO community since the early 1960s had been adopted by the superconducting qubit community to measure the state of their qubits. These superconducting qubits, representing atoms, which are coupled to a resonant structure on chip, which represents the photons that can interact with the artificial atom. Since these systems were not traditional trapped or neutral atoms interacting with a photon via a laser, but instead planar circuit structures, the superconducting qubit community re-coined the term cavity quantum electrodynamics to circuit quantum electrodynamics, which we will refer to as cQED.The quantum dot community adapted these methods of what is known as dispersive readout; a capacitive change of the atomic like system, results in a dispersive shift which then alters the characteristic frequency response of the resonant structure. This has allowed for a new kind of charge sensor by means of measuring the resonators response due to its coupling to a quantum dot system. This can be done with very high frequency microwave circuitry, allowing much faster readout than is capable via traditional charge sensors. Thus, allowing a pathway to implement quantum error correction schemes with reasonable times compared to any dephasing or decoherence times of the semiconductor system. Furthermore, such fast readout allows for feedback protocols to be implemented to the system to correct for certain undesirable effects due to instruments or the system itself. Our work focuses on a limit of this cQED interaction of the quantum dots to a resonant structure allowing us to do fast readout of the quantum dot charge states via a dispersive shift.The work I will demonstrate in this dissertation will be in the efforts of fast readout on the charge occupation of a double quantum dot system which is galvanically coupled to a superconducting microwave resonator. This was done in a Si/SiGe heterostructure system where I designed, simulated, and fabricated the device which was optimized to have a stronger dispersive shift signal due to an enhanced gate lever arm that couples to the resonator. I will discuss our results of attaining a minimum integration time of 34.54 ns for a unity signal to noise ratio. This demonstrates a fast readout system in the community iii which could be extended to allow for even better readout speeds with faster instruments than what were available to me for the experiment. I will further discuss our characterization of the hybrid system and how we extracted a charge noise due to charging events between the two dots in our system up to around 10 kHz. This work demonstrates a robust dispersive readout scheme which helps in the scalability of hybrid superconducting-semiconducting architectures for means of quantum information processing.

•Dec 12, 2025•0 citations

Flip-chip integrated superconducting qubits using electroplated bump bonds

Yen-An Shih, Rebecca Gharibaan, Barka Khan +9 more

Flip-chip integration offers a promising route toward scalable superconducting quantum processors and hybrid semiconductor-superconductor quantum devices. We develop a three-dimensional transmon architecture using electroplated indium in which the qubit electric field is shared nearly equally between two bump-bonded substrates while maintaining low participation at the indium-bump interface. The resulting geometry is well suited for future hybrid qubits, enabling the integration of distinct material platforms while minimizing sensitivity to bump-interface loss. Using this platform, we evaluate electroplated indium interconnects for superconducting quantum circuits. Flip-chip transmons incorporating electroplated indium bumps exhibit qubit quality factors around $10^6$. In addition, a systematic study of coplanar-waveguide resonators is used to identify losses associated with the electroplating process. In particular, we find that surface losses associated with the gold-layer, used to enable good electric contact with the indium, is likely the primary contributor to the qubit decay rate. These results demonstrate the compatibility of electroplated indium technology with high-coherence superconducting circuits and establish a promising platform for three-dimensional hybrid quantum integration.

quant-pharXiv:2608.07306•Aug 10, 2026•0 citations
Heterogeneous integration provides a promising route to combine semiconductor quantum dot devices and superconducting microwave circuits, while allowing each component to be fabricated using an optimized process flow. Here, we demonstrate a flip-chip integrated platform for dispersive readout of silicon metal-oxide semiconductor (SiMOS) quantum dot devices. A SiMOS double quantum dot chip is bonded to a superconducting aluminum resonator chip using indium bump interconnects to enable microwave coupling to the quantum dot gate. We show that the developed flip-chip process is compatible with cryogenic operation of both the SiMOS device and the superconducting resonator, and demonstrate resonator-based detection of charge transitions in the quantum dot system. The readout signal-to-noise ratio follows a dependence of t\sqrt{t}t​ with the integration time, reaching SNR = 1 at an integration time of approximately 0.3 ms. These results establish flip-chip bonding as a viable integration approach for SiMOS quantum dot devices operating at both dc and microwave frequencies, with potential applications for resonator-based techniques such as spin-photon coupling.
Semiconductor quantum dots in silicon demonstrate exceptionally long spin lifetimes as qubits and are therefore promising candidates for quantum information processing. However, control and readout techniques for these devices have thus far employed low frequency electrons, in contrast to high speed temperature readout techniques used in other qubit architectures, and coupling between multiple quantum dot qubits has not been satisfactorily addressed.This dissertation presents the design and characterization of a semiconductor charge qubit based on double quantum dot in silicon with an integrated microwave resonator for control and readout. The 6 GHz resonator is designed to achieve strong coupling with the quantum dot qubit, allowing the use of circuit QED control and readout techniques which have not previously been applicable to semiconductor qubits. To achieve this coupling, this document demonstrates successful operation of a novel silicon double quantum dot design with a single active metallic layer and a coplanar stripline resonator with a bias tee for dc excitation.Experiments presented here demonstrate quantum localization and measurement of both electrons on the quantum dot and photons in the resonator. Further, it is shown that the resonator-qubit coupling in these devices is sufficient to reach the strong coupling regime of circuit QED. The details of a measurement setup capable of performing simultaneous low noise measurements of the resonator and quantum dot structure are also presented here.The ultimate aim of this research is to integrate the long coherence times observed in electron spins in silicon with the sophisticated readout architectures available in circuit QED based quantum information systems. This would allow superconducting qubits to be coupled directly to semiconductor qubits to create hybrid quantum systems with separate quantum memory and processing components.
Hybrid circuit quantum electrodynamics (cQED) aims at coupling various quantum degrees of freedom, among which are spin and charge degrees of freedom in gate defined quantum dots, phonons or magnons... with quantized electromagnetic fields in superconducting microwave cavities to investigate fundamental physics questions or for quantum computation and simulation. However, low microwave losses, key for many hybrid cQED experiments, are challenging to achieve given the often exotic and/or complex material stacks (e.g. semiconducting material, ferromagnets, or piezoelectric materials) required to host the various quantum degrees of freedom. In this work, we present a 3D-integration process to overcome this challenge for semi-industrial silicon MOS spin qubits. The process is based on dense indium bump interconnects at a pitch of 10 μ\mathrmμμm and superconducting thin films of Niobium Nitride (NbN). First, we report on DC and RF interconnect properties that demonstrate a high galvanic interconnection yield and internal quality factors above 10510^{5}105 in the single photon regime for NbN resonators interrupted by a single indium bump interconnect. Eventually, we fabricated a 3D-integrated hybrid circuit quantum electrodynamics (cQED) device based on a semi-industrial MOS hole double quantum dot and a high impedance NbN resonator. For this device, we report a cavity internal quality factor above 10000 and demonstrate record sensitivity for gate-based dispersive readout of the charge degree of freedom with an SNR of 100 in 300 ns. Finally, we demonstrate strong spin-photon coupling of gs/2πg_{s}/2πgs​/2π = 75 MHz, which highlights the viability of 3D-integration for quantum dot based hybrid spin circuit quantum electrodynamics and opens to high-fidelity spin readout and microwave photon-based remote spin qubit entanglement.
Fast measurements of quantum devices is useful in areas such as quantum sensing, quantum computing, and nanodevice quality analysis. Here, we develop a superconductor-semiconductor multimodule microwave assembly to demonstrate charge-state readout at the state of the art. The assembly consist of a superconducting readout resonator interfaced to a silicon-on-insulator (SOI) chiplet containing quantum dots (QDs) in a high- κ nanowire transistor. The superconducting chiplet contains resonant and coupling elements as well as L C filters that, when interfaced with the silicon chip, result in a resonant frequency f = 2.12 GHz, a loaded quality factor Q = 850 , and a resonator impedance Z = 470 Ω . Combined with the large gate lever arms of SOI technology, we achieve a minimum integration time for single and double QD transitions of 2.77 and 13.5 ns, respectively. We utilize the assembly to measure charge noise over 9 decades of frequency up to 500 kHz and find a 1 / f dependence across the whole frequency spectrum as well as a charge-noise level of 4 μ eV / Hz at 1 Hz. The modular microwave circuitry presented here can be directly utilized in conjunction with other quantum devices to improve the readout performance as well as enable large bandwidth noise spectroscopy, all without the complexity of superconductor-semiconductor monolithic fabrication. Published by the American Physical Society 2024
The properties of superconducting devices depend sensitively on the parity (even or odd) of the quasiparticles that they contain. Encoding quantum information in the parity degree of freedom is central in several emerging solid-state qubit architectures, including in hybrid superconductor-semiconductor devices. In the latter case, accurate, nondestructive, and time-resolved parity measurements are a challenging issue. Here, we report on control and real-time parity measurement in a superconducting island embedded in a superconducting loop and realized in a hybrid two-dimensional heterostructure using a microwave resonator. To avoid microwave losses impeding time-resolved measurements, the device and readout resonator are located on separate chips, connected via flip-chip bonding, and couple inductively through vacuum. The superconducting resonator detects the parity-dependent circuit inductance, allowing for fast parity readout. We have resolved even- and odd-parity states with a signal-to-noise ratio of SNR ≈ 3 for an integration time of 20 μ s and a detection fidelity exceeding 98 % . The real-time parity measurement shows a state lifetime extending into the millisecond range. Our approach will lead to a better understanding of coherence-limiting mechanisms in superconducting quantum hardware and help to advance inductive-readout schemes for hybrid qubits. Published by the American Physical Society 2024
The need for fast readout to measure the state of a quantum dot device has important applications in the capabilities of using them as a means for quantum information processing. Traditional charge sensors used to readout the charge state of a quantum dot device are very robust and sensitive electrometers that have been in use since the late 1980s. They pose an issue to the future of quantum dots as a viable means of quantum computing, and that is in their slow acquisition times of the charge state of the quantum dot. This rate of measurement means that implementing any quantum error correction scheme becomes very difficult or even unfeasible as the coherence times of these semiconductor systems is short compared to charge sensor’s acquisition times. A possibility to speed up the measurement process of the charge state is possible thanks to the atomic molecular and optical (AMO) physics community.Cavity quantum electrodynamics (CQED) is the study of light-matter interactions when both the light and matter are taken to be quantized. A photon may interact with an atom via a dipole interaction to excite it from its ground state to its excited state, and the reverse can occur where the atom emits a photon and decays from its excited state ii to the ground state. This fundamental interaction which has been extensively studied in the AMO community since the early 1960s had been adopted by the superconducting qubit community to measure the state of their qubits. These superconducting qubits, representing atoms, which are coupled to a resonant structure on chip, which represents the photons that can interact with the artificial atom. Since these systems were not traditional trapped or neutral atoms interacting with a photon via a laser, but instead planar circuit structures, the superconducting qubit community re-coined the term cavity quantum electrodynamics to circuit quantum electrodynamics, which we will refer to as cQED.The quantum dot community adapted these methods of what is known as dispersive readout; a capacitive change of the atomic like system, results in a dispersive shift which then alters the characteristic frequency response of the resonant structure. This has allowed for a new kind of charge sensor by means of measuring the resonators response due to its coupling to a quantum dot system. This can be done with very high frequency microwave circuitry, allowing much faster readout than is capable via traditional charge sensors. Thus, allowing a pathway to implement quantum error correction schemes with reasonable times compared to any dephasing or decoherence times of the semiconductor system. Furthermore, such fast readout allows for feedback protocols to be implemented to the system to correct for certain undesirable effects due to instruments or the system itself. Our work focuses on a limit of this cQED interaction of the quantum dots to a resonant structure allowing us to do fast readout of the quantum dot charge states via a dispersive shift.The work I will demonstrate in this dissertation will be in the efforts of fast readout on the charge occupation of a double quantum dot system which is galvanically coupled to a superconducting microwave resonator. This was done in a Si/SiGe heterostructure system where I designed, simulated, and fabricated the device which was optimized to have a stronger dispersive shift signal due to an enhanced gate lever arm that couples to the resonator. I will discuss our results of attaining a minimum integration time of 34.54 ns for a unity signal to noise ratio. This demonstrates a fast readout system in the community iii which could be extended to allow for even better readout speeds with faster instruments than what were available to me for the experiment. I will further discuss our characterization of the hybrid system and how we extracted a charge noise due to charging events between the two dots in our system up to around 10 kHz. This work demonstrates a robust dispersive readout scheme which helps in the scalability of hybrid superconducting-semiconducting architectures for means of quantum information processing.
Flip-chip integration offers a promising route toward scalable superconducting quantum processors and hybrid semiconductor-superconductor quantum devices. We develop a three-dimensional transmon architecture using electroplated indium in which the qubit electric field is shared nearly equally between two bump-bonded substrates while maintaining low participation at the indium-bump interface. The resulting geometry is well suited for future hybrid qubits, enabling the integration of distinct material platforms while minimizing sensitivity to bump-interface loss. Using this platform, we evaluate electroplated indium interconnects for superconducting quantum circuits. Flip-chip transmons incorporating electroplated indium bumps exhibit qubit quality factors around 10610^6106. In addition, a systematic study of coplanar-waveguide resonators is used to identify losses associated with the electroplating process. In particular, we find that surface losses associated with the gold-layer, used to enable good electric contact with the indium, is likely the primary contributor to the qubit decay rate. These results demonstrate the compatibility of electroplated indium technology with high-coherence superconducting circuits and establish a promising platform for three-dimensional hybrid quantum integration.