Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2604.08955

Impact of Pump Phase-Noise on Josephson Traveling-Wave Parametric Amplifiers

Daryoush Shiri, Likai Yang, Saesun Kim, Mohamed A. Hassan, Philip Krantz, Eric T. Holland

quant-phSubmitted Apr 10, 2026• Announced Apr 13, 2026• 1 citation
arXivHTMLPDF

Abstract

Superconducting traveling-wave parametric amplifiers (TWPAs) are essential elements for enhancing the signal-to-noise ratio (SNR) and thus the read-out fidelity of superconducting qubits because of their high gain and near quantum-limited noise. However, the impact of the pump source, e.g., phase noise on these amplifiers, has not yet been studied. In this work, we show that among the two amplification processes in JTWPAs, the three-wave mixing (3WM) process is more sensitive to the pump phase noise than the four-wave mixing (4WM) process. We show that the even-order nonlinearity of 4th order and above in three-wave mixing is responsible for more than 10 dB increase of phase noise at high frequency offsets within the phase noise mask as the power of the pump increases. A polynomial model of the amplifier and cyclo-stationary property of phase noise also corroborate with the simulations. The Harmonic Balance (HB) periodic noise analysis tool and Leeson phase noise model in Keysight Advanced Design System (ADS) simulator were used in this study.

Comments
6 pages, 8 figures,

Related papers

Design of a Traveling-Wave Parametric Amplifier with a π -Josephson Junction

Shuyuan Cui, Daiki Fukuyo, Hiroshi Shimada +1 more

Abstract A Josephson traveling-wave parametric amplifier (JTWPA) is indispensable for the high-fidelity readout of superconducting qubits, owing to its broadband gain and near-quantum-limited noise performance. Conventional JTWPAs implemented with 0-Josephson junctions (0-JTWPAs) avoid magnetic-flux bias but rely on Kerr nonlinearity, which leads to pump-power-dependent phase mismatch, gain ripple, and a limited dynamic range. More recently, three-wave-mixing (3WM) JTWPAs employing flux-biased rf-SQUIDs have been proposed to suppress Kerr effects. However, these designs require a significant external flux bias per unit cell, which complicates cryogenic hardware, introduces sensitivity to flux noise, and limits scalability in large arrays. In this study, we propose and analyze a π -junction-based JTWPA ( π -JTWPA) in which the intrinsic π phase shift of the junction effectively displaces the operating point of the current–phase relation. This approach aims to realize 3WM-type nonlinearity with reduced flux bias while preserving broadband amplification, thereby simplifying flux-bias distribution, enhancing robustness against flux noise, and providing a pathway toward scalable, multiplexed quantum readout architectures. In addition, we examine the potential applicability of the π -JTWPA in four-wave-mixing (4WM) operation.

Journal of Physics Conference Series•Jul 1, 2026•0 citations

Designing Josephson Traveling-Wave Parametric Amplifiers: EM-Circuit Cosimulation and Experimental Validation

Likai Yang, Jennifer Wang, Daryoush Shiri +6 more

The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.

IEEE Transactions on Applied Superconductivity•May 20, 2026•0 citations

Field-induced phase-matching in Josephson traveling wave parametric amplifiers

Daniil E. Bazulin, S. Gandorfer, N. Bruckmoser +9 more

Superconducting Josephson traveling wave parametric amplifiers (JTWPAs) enable broadband, quantum-limited amplification of weak microwave signals. JTWPAs are essential for the single-shot readout of superconducting qubits, broadband vacuum squeezing, or the generation of microwave cluster states. Phase-matching between signal and pump modes in such JTWPAs represents a major engineering challenge, which is typically solved by integrating resonators in a nonlinear medium in order to tailor electromagnetic dispersion relations and achieve a broadband, high-gain amplification. Here, we experimentally demonstrate a phase-matching approach using a homogeneous nonlinear medium based on Josephson elements by exploiting a magnetic field inhomogeneity. We show how the latter may lead to the sign reversal of the 3-wave mixing nonlinearity and stabilization of the parametric amplification. We envision this technique as a viable alternative to conventional phase-matching approaches.

arXiv:2611.13084•Nov 9, 2026•0 citations

Gain compression in Josephson traveling-wave parametric amplifiers

Gwenael Le Gal, Guilliam Butseraen, Arpit Ranadive +6 more

Superconducting traveling-wave parametric amplifiers (TWPAs) are increasingly used in various applications, including quantum computing, quantum sensing, and dark matter detection. However, one important characteristic of these amplifiers, gain compression, has not received much attention. As a result, there is a lack of comprehensive experimental exploration of this phenomenon in the existing literature. In this study, we present an experimental investigation of gain compression in a Josephson traveling-wave parametric amplifier based on a four-wave mixing process. We have implemented a novel setup to monitor the complex transmission of both the pump and signal tones, which allows us to simultaneously track pump depletion and signal amplification as functions of signal power and frequency across the entire bandwidth of the device. Our findings indicate that, while pump depletion occurs during gain compression, it is not the only mechanism involved in the saturation of a TWPA. Power-induced phase-matching processes also take place within the device. This study provides valuable insights for optimizing TWPAs for applications that require high total input power, such as multiplexed qubit readout or broadband photon emission.

arXiv:2502.03022•Physical Review Applied•Jun 4, 2025•6 citations

Nonlinear Behavior of Josephson Traveling Wave Parametric Amplifiers

Claudio Guarcello, Felix Ahrens, Guerino Avallone +40 more

Recent advancements in quantum technologies and advanced detection experiments have underscored the pressing need for the detection of exceedingly weak signals within the microwave frequency spectrum. Addressing this challenge, the Josephson Traveling Wave Parametric Amplifier (JTWPA) has been proposed as a cryogenic front-end amplifier capable of approaching the quantum noise limit while providing a relevant bandwidth. This research is centered on a comprehensive numerical investigation of the JTWPA, without resorting to simplifications regarding the nonlinearity of the essential components. Specifically, this study focuses on a thorough examination of the system, characterized by coupled nonlinear differential equations representing all components of the device. Proper input and output signals at the device's boundaries are considered. The analysis of the output signals undergoing the parametric amplification process involves a detailed exploration of phase-space dynamics and Fourier spectral analysis of the output voltage. This study is conducted while considering the parameters ruling the response of the device under pump and signal excitations. In addition to the expected signal amplification, the findings reveal that the nonlinear nature of the system can give rise to unforeseen phenomena, depending on the system's operational conditions, which include: the generation of pump tone harmonics, modulation of the signal gain, and incommensurate frequency generation—effects that are not easily accommodated by simplistic linearized approaches.

arXiv:2403.01597•IEEE Transactions on Applied Superconductivity•Feb 20, 2024•8 citations

Characterisation of a travelling-wave parametric amplifier for improved qubit measurements

Hampus Renberg Nilsson

In order to build a large-scale quantum computer, one of the requirements is high-fidelity multiplexed qubit readout, which in turn relies on the use of ultralow-noise amplifiers. While Josephson Parametric Amplifiers (JPAs), using a cavity with few Josephson junctions, have shown promising results for single qubit readout, they have limitations such as low saturation power and a gain-bandwidth product restriction. This makes them less suited for frequency multiplexed qubit readout. A current-pumped Josephson Travelling-Wave Parametric Amplifier (JTWPA), using 4-wave mixing in a lumped-element transmission line, features both high saturation power as well as no restriction on large bandwidth and high gain. This is possible due to multiple junctions and the lack of a cavity. However, also this current pumped JTWPA has an inherent problem, namely phase mismatch between the pump and the signal. This prevents exponential gain. In this thesis, a current pumped JTWPA using the resonant phase matching (RPM) technique to reduce the phase mismatch problem is studied and characterised. The JTWPA shows high gain, high saturation power and a large signal-to-noise ratio improvement. The JTWPA is also used for qubit readout, for which it clearly improves the readout fidelity.

•Jan 1, 2019•0 citations
Superconducting traveling-wave parametric amplifiers (TWPAs) are essential elements for enhancing the signal-to-noise ratio (SNR) and thus the read-out fidelity of superconducting qubits because of their high gain and near quantum-limited noise. However, the impact of the pump source, e.g., phase noise on these amplifiers, has not yet been studied. In this work, we show that among the two amplification processes in JTWPAs, the three-wave mixing (3WM) process is more sensitive to the pump phase noise than the four-wave mixing (4WM) process. We show that the even-order nonlinearity of 4th order and above in three-wave mixing is responsible for more than 10 dB increase of phase noise at high frequency offsets within the phase noise mask as the power of the pump increases. A polynomial model of the amplifier and cyclo-stationary property of phase noise also corroborate with the simulations. The Harmonic Balance (HB) periodic noise analysis tool and Leeson phase noise model in Keysight Advanced Design System (ADS) simulator were used in this study.
Abstract A Josephson traveling-wave parametric amplifier (JTWPA) is indispensable for the high-fidelity readout of superconducting qubits, owing to its broadband gain and near-quantum-limited noise performance. Conventional JTWPAs implemented with 0-Josephson junctions (0-JTWPAs) avoid magnetic-flux bias but rely on Kerr nonlinearity, which leads to pump-power-dependent phase mismatch, gain ripple, and a limited dynamic range. More recently, three-wave-mixing (3WM) JTWPAs employing flux-biased rf-SQUIDs have been proposed to suppress Kerr effects. However, these designs require a significant external flux bias per unit cell, which complicates cryogenic hardware, introduces sensitivity to flux noise, and limits scalability in large arrays. In this study, we propose and analyze a π -junction-based JTWPA ( π -JTWPA) in which the intrinsic π phase shift of the junction effectively displaces the operating point of the current–phase relation. This approach aims to realize 3WM-type nonlinearity with reduced flux bias while preserving broadband amplification, thereby simplifying flux-bias distribution, enhancing robustness against flux noise, and providing a pathway toward scalable, multiplexed quantum readout architectures. In addition, we examine the potential applicability of the π -JTWPA in four-wave-mixing (4WM) operation.
The development of large-scale superconducting quantum computers critically depends on the accurate readout of qubit states. To enable this, cryogenic parametric amplifiers have been proposed and developed, and have since found widespread use in small-signal detection applications. Among various amplifier architectures, Josephson traveling-wave parametric amplifiers (JTWPAs) are widely adopted due to their broad bandwidth, high saturation power, and compatibility with superconducting qubits. In this work, we present a design workflow of JTWPAs based on a co-simulation approach combining electromagnetic (EM) and circuit-level simulation. We apply this method to a uniform JTWPA, comparing our simulation results with experimental data. To mitigate the challenge of constructing lumped element circuit models usually used in conventional simulation method, we directly perform full EM analysis of the device to accurately determine its linear response. The extracted S parameters are then fed into a nonlinear harmonic balance simulator with Josephson junctions modeled as circuit elements. By doing so, the linear and gain properties of the JTWPA are extracted. Different factors that impact device performance including gain compression, phase matching, and fabrication imperfections are further investigated and modeled. A good agreement between simulation and measurements is identified, establishing the effectiveness of our approach in designing quantum parametric amplifiers.
Superconducting Josephson traveling wave parametric amplifiers (JTWPAs) enable broadband, quantum-limited amplification of weak microwave signals. JTWPAs are essential for the single-shot readout of superconducting qubits, broadband vacuum squeezing, or the generation of microwave cluster states. Phase-matching between signal and pump modes in such JTWPAs represents a major engineering challenge, which is typically solved by integrating resonators in a nonlinear medium in order to tailor electromagnetic dispersion relations and achieve a broadband, high-gain amplification. Here, we experimentally demonstrate a phase-matching approach using a homogeneous nonlinear medium based on Josephson elements by exploiting a magnetic field inhomogeneity. We show how the latter may lead to the sign reversal of the 3-wave mixing nonlinearity and stabilization of the parametric amplification. We envision this technique as a viable alternative to conventional phase-matching approaches.
Superconducting traveling-wave parametric amplifiers (TWPAs) are increasingly used in various applications, including quantum computing, quantum sensing, and dark matter detection. However, one important characteristic of these amplifiers, gain compression, has not received much attention. As a result, there is a lack of comprehensive experimental exploration of this phenomenon in the existing literature. In this study, we present an experimental investigation of gain compression in a Josephson traveling-wave parametric amplifier based on a four-wave mixing process. We have implemented a novel setup to monitor the complex transmission of both the pump and signal tones, which allows us to simultaneously track pump depletion and signal amplification as functions of signal power and frequency across the entire bandwidth of the device. Our findings indicate that, while pump depletion occurs during gain compression, it is not the only mechanism involved in the saturation of a TWPA. Power-induced phase-matching processes also take place within the device. This study provides valuable insights for optimizing TWPAs for applications that require high total input power, such as multiplexed qubit readout or broadband photon emission.
Recent advancements in quantum technologies and advanced detection experiments have underscored the pressing need for the detection of exceedingly weak signals within the microwave frequency spectrum. Addressing this challenge, the Josephson Traveling Wave Parametric Amplifier (JTWPA) has been proposed as a cryogenic front-end amplifier capable of approaching the quantum noise limit while providing a relevant bandwidth. This research is centered on a comprehensive numerical investigation of the JTWPA, without resorting to simplifications regarding the nonlinearity of the essential components. Specifically, this study focuses on a thorough examination of the system, characterized by coupled nonlinear differential equations representing all components of the device. Proper input and output signals at the device's boundaries are considered. The analysis of the output signals undergoing the parametric amplification process involves a detailed exploration of phase-space dynamics and Fourier spectral analysis of the output voltage. This study is conducted while considering the parameters ruling the response of the device under pump and signal excitations. In addition to the expected signal amplification, the findings reveal that the nonlinear nature of the system can give rise to unforeseen phenomena, depending on the system's operational conditions, which include: the generation of pump tone harmonics, modulation of the signal gain, and incommensurate frequency generation—effects that are not easily accommodated by simplistic linearized approaches.
In order to build a large-scale quantum computer, one of the requirements is high-fidelity multiplexed qubit readout, which in turn relies on the use of ultralow-noise amplifiers. While Josephson Parametric Amplifiers (JPAs), using a cavity with few Josephson junctions, have shown promising results for single qubit readout, they have limitations such as low saturation power and a gain-bandwidth product restriction. This makes them less suited for frequency multiplexed qubit readout. A current-pumped Josephson Travelling-Wave Parametric Amplifier (JTWPA), using 4-wave mixing in a lumped-element transmission line, features both high saturation power as well as no restriction on large bandwidth and high gain. This is possible due to multiple junctions and the lack of a cavity. However, also this current pumped JTWPA has an inherent problem, namely phase mismatch between the pump and the signal. This prevents exponential gain. In this thesis, a current pumped JTWPA using the resonant phase matching (RPM) technique to reduce the phase mismatch problem is studied and characterised. The JTWPA shows high gain, high saturation power and a large signal-to-noise ratio improvement. The JTWPA is also used for qubit readout, for which it clearly improves the readout fidelity.