Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2604.00229

A Security-Aware Nonlinearity Study of FPGA-Based Time-to-Digital Converters for Quantum Key Distribution Systems

Kun Qin, Carsten Trinitis

quant-phcs.ARSubmitted Mar 31, 2026• Announced Apr 2, 2026• 0 citations
arXivHTMLPDF

Abstract

Intrinsic nonlinearity in FPGA-based time-to-digital converters (TDCs) is often treated as a calibration issue and evaluated mainly through post-correction metrics. In quantum key distribution (QKD), however, raw delay-line nonuniformity can affect coincidence timing and thereby influence accidental-coincidence rate and Quantum Bit Error Rate (QBER). This paper analyzes how measured FPGA-TDC nonlinearity propagates to QKD timing metrics using a conservative system-level model that combines random timing uncertainty and deterministic nonlinearity. We also propose fabric-level mitigation strategies based on LUT-assisted delay shaping and placement constraints to reduce severe bin-width irregularities without statistical calibrations. The method is evaluated by reproducing two open-source TDCs implemented on a low-cost Zynq-7000 FPGA. We observe reductions of 14\%-21\% in integral nonlinearity (INL) compared with the non-optimized design, leading to a reduced QBER contribution and an improvement by 3.7\%-14.2\% in the estimated secret fraction. These results suggest that raw FPGA-TDC nonlinearity deserves explicit consideration in timing-sensitive QKD implementations.

Related papers

An FPGA-Based TDC for Free Space Quantum Key Distribution

Qi Shen, Sheng‐Kai Liao, Shubin Liu +4 more

Quantum key distribution (QKD) is the most matured application of quantum communication. The time synchronization and system timing jitter are essential to a practical QKD experiment, which can directly influence the quantum bit error rate (QBER) and the final key rate. High precision time-to-digital converters (TDCs) can effectively reduce the system timing jitter, resulting in lower QBER and higher key rate. Here, we introduce a TDC based on a field programmable gate array (FPGA). Its high resolution (LSB) of 50 ps with precision (RMS) less than 50 ps, low dead time and large dynamic range can well meet the requirement of the QKD experiment. A free space QKD system setup using the FPGA-based TDC has been assembled. The timing precision of the synchronous light and the system timing jitter were determined. The results demonstrate that the FPGA-based TDC could be successfully applied in the QKD experiment.

IEEE Transactions on Nuclear Science•Oct 1, 2013•27 citations

Time interval analyzer with FPGA-based TDC for free space quantum key distribution: Principle and validation with prototype setup

Qi Shen, Sheng‐Kai Liao, Shubin Liu +4 more

Quantum key distribution (QKD) is the most matured application of quantum communication. The time synchronization and system timing jitter are essential to a practical QKD experiment, which can directly influence the quantum bit error rate (QBER) and the final key rate. High precision time-to-digital convertor (TDC) can effectively reduce the system timing jitter, resulting in lower QBER and higher key rate. Here, we introduce a TDC based on a field-programmable gate array (FPGA). Its high resolution of 50 ps, low dead time and large dynamic range can well meet the requirement of the QKD experiment. A free space QKD system setup using the FPGA-based TDC has been built up. The timing precision of the synchronous light and the system timing jitter were tested. The results demonstrate that the FPGA-based TDC could be successfully applied in the QKD experiment.

IEEE-NPSS Real-Time Conference•Jun 1, 2012•3 citations

A Time-to-Digital Converter With Steady Calibration Through Single-Photon Detection

Matías Rubén Bolaños, Daniele Vogrig, Paolo Villoresi +2 more

Time-to-Digital Converters (TDCs) are a crucial tool in a wide array of fields, in particular for quantum communication, where time taggers performance can severely affect the quality of the entire application. Nowadays, FPGA-based TDCs present a viable alternative to ASIC ones, once the non-linear behavior due to the intrinsic nature of the device is properly mitigated. To compensate for said nonlinearities, a calibration procedure is required, which should be maintained throughout its runtime. Here we present the design and the demonstration of a TDC that is FPGA-based showing a residual FWHM jitter of 27 ps, that is scalable for multichannel operation. The target application in Quantum Key Distribution (QKD) is discussed with a calibration method based on the exploitation of single-photon detection that does not require stopping the data acquisition or using any estimation methods, thus increasing accuracy and removing data loss. The calibration was tested in a relevant environment, investigating the behavior of the device between 5 °C and 80 °C. Moreover, our design is capable of continuously streaming up to 12 Mevents/s for up to ~1 week without the TDC overflowing making it ready for a real-life scenario deployment.

arXiv:2406.01293•IEEE Transactions on Instrumentation and Measurement•Jan 1, 2025•8 citations

FPGA-based TDC for QKD

Compte Prades, Joel

High-resolution time measurement is a fundamental building block on a wide variety of applications such as time-of-flight based systems, single-photon microscopy and quantum communications. FPGA-based TDCs are the preferred choice for cost-effective implementations requiring both high performance and flexibility. In this work, a Tapped-Delay Line (TDL) and Wave Union Tapped-Delay Line (WU TDL) TDC architectures are implemented and characterized on a Zynq Ultrascale+ FPGA-board. The characterization will mainly focus on determining the resolution and linearity of both TDCs. A bin merging algorithm is also tested to see the increment of linearity at expense of resolution. The TDL and WU TDL implementations were tested measuring the time difference of two signals obtaining 11.6 ps and 11.4 ps RMS resolution respectively. The achieved performance allow the proposed implementations to be integrated in high-resolution time measuring systems.

•Sep 6, 2023•0 citations

Time-spectral control of accidental coincidences in daylight entanglement-based free-space QKD

Jiyoung Moon, Yonggi Jo, Zaeill Kim +2 more

Daylight entanglement-based free-space quantum key distribution (QKD) is limited by accidental coincidences from receiver-admitted background light. We develop and experimentally validate a receiver-level framework anchored to measured singles rates and reference coincidence components, linking receiver bandwidth, accepted temporal width, and background-noise density to Bob singles, sifted-key rate, error rate, and quantum bit error rate (QBER) in telecom-wavelength BBM92 QKD. Indoor sweeps show that the sifted-key rate saturates near the source-matched bandwidth, whereas broader bandwidth or higher background mainly increases accidental contamination. Increasing the accepted temporal width leaves Bob singles nearly unchanged but directly raises QBER by enlarging the random-overlap probability. A two-dimensional design map calculated from the model shows that the temporal-window margin contracts rapidly with increasing background-to-signal ratio, while the bandwidth margin remains comparatively broad near source-matched filtering. A rooftop experiment demonstrates daylight operation over a 10 m free-space link, yielding a mean sifted-key rate of 2,811 cps and a mean QBER of 4.43%. This framework provides a quantitative basis for choosing receiver bandwidth and temporal acceptance to meet a target QBER under specified background conditions.

quant-pharXiv:2606.17365•Jun 17, 2026•0 citations

Adaptation of Error Correction Procedures to the Time-Bin Quantum Key Distribution Protocol Implementation

Vladimir Morozov, Mikhail S. Elezov, Oleg Olegovich Evsutin +1 more

Error correction is a crucial stage in quantum key distribution (QKD) protocols—a promising field of modern cryptography where the secrecy of the shared key information is guaranteed by the laws of quantum mechanics. Currently, there are many effective approaches to error correction in QKD. However, most of them, due to their generic nature, fail to leverage the specific features of particular protocol implementations. This work demonstrates that accounting for the hardware specifics of a QKD system implementing the time-bin protocol enables a significant increase in error correction performance. For the considered QKD system, we have experimentally obtained estimates of the Quantum Bit Error Rate (QBER) observed for each combination of bit and detector. The differences in the obtained estimates reveal that the quantum channel can be modeled as a non-uniform binary channel. Furthermore, based on computational experiments with a model of the quantum channel, it was established that adapting the error correction procedure to its properties can achieve up to a 2.7-fold reduction in the LDPC code decoding failure rate at low error levels.

IEEE Access•Dec 26, 2025•1 citation
Intrinsic nonlinearity in FPGA-based time-to-digital converters (TDCs) is often treated as a calibration issue and evaluated mainly through post-correction metrics. In quantum key distribution (QKD), however, raw delay-line nonuniformity can affect coincidence timing and thereby influence accidental-coincidence rate and Quantum Bit Error Rate (QBER). This paper analyzes how measured FPGA-TDC nonlinearity propagates to QKD timing metrics using a conservative system-level model that combines random timing uncertainty and deterministic nonlinearity. We also propose fabric-level mitigation strategies based on LUT-assisted delay shaping and placement constraints to reduce severe bin-width irregularities without statistical calibrations. The method is evaluated by reproducing two open-source TDCs implemented on a low-cost Zynq-7000 FPGA. We observe reductions of 14%-21% in integral nonlinearity (INL) compared with the non-optimized design, leading to a reduced QBER contribution and an improvement by 3.7%-14.2% in the estimated secret fraction. These results suggest that raw FPGA-TDC nonlinearity deserves explicit consideration in timing-sensitive QKD implementations.
Quantum key distribution (QKD) is the most matured application of quantum communication. The time synchronization and system timing jitter are essential to a practical QKD experiment, which can directly influence the quantum bit error rate (QBER) and the final key rate. High precision time-to-digital converters (TDCs) can effectively reduce the system timing jitter, resulting in lower QBER and higher key rate. Here, we introduce a TDC based on a field programmable gate array (FPGA). Its high resolution (LSB) of 50 ps with precision (RMS) less than 50 ps, low dead time and large dynamic range can well meet the requirement of the QKD experiment. A free space QKD system setup using the FPGA-based TDC has been assembled. The timing precision of the synchronous light and the system timing jitter were determined. The results demonstrate that the FPGA-based TDC could be successfully applied in the QKD experiment.
Quantum key distribution (QKD) is the most matured application of quantum communication. The time synchronization and system timing jitter are essential to a practical QKD experiment, which can directly influence the quantum bit error rate (QBER) and the final key rate. High precision time-to-digital convertor (TDC) can effectively reduce the system timing jitter, resulting in lower QBER and higher key rate. Here, we introduce a TDC based on a field-programmable gate array (FPGA). Its high resolution of 50 ps, low dead time and large dynamic range can well meet the requirement of the QKD experiment. A free space QKD system setup using the FPGA-based TDC has been built up. The timing precision of the synchronous light and the system timing jitter were tested. The results demonstrate that the FPGA-based TDC could be successfully applied in the QKD experiment.
Time-to-Digital Converters (TDCs) are a crucial tool in a wide array of fields, in particular for quantum communication, where time taggers performance can severely affect the quality of the entire application. Nowadays, FPGA-based TDCs present a viable alternative to ASIC ones, once the non-linear behavior due to the intrinsic nature of the device is properly mitigated. To compensate for said nonlinearities, a calibration procedure is required, which should be maintained throughout its runtime. Here we present the design and the demonstration of a TDC that is FPGA-based showing a residual FWHM jitter of 27 ps, that is scalable for multichannel operation. The target application in Quantum Key Distribution (QKD) is discussed with a calibration method based on the exploitation of single-photon detection that does not require stopping the data acquisition or using any estimation methods, thus increasing accuracy and removing data loss. The calibration was tested in a relevant environment, investigating the behavior of the device between 5 °C and 80 °C. Moreover, our design is capable of continuously streaming up to 12 Mevents/s for up to ~1 week without the TDC overflowing making it ready for a real-life scenario deployment.
High-resolution time measurement is a fundamental building block on a wide variety of applications such as time-of-flight based systems, single-photon microscopy and quantum communications. FPGA-based TDCs are the preferred choice for cost-effective implementations requiring both high performance and flexibility. In this work, a Tapped-Delay Line (TDL) and Wave Union Tapped-Delay Line (WU TDL) TDC architectures are implemented and characterized on a Zynq Ultrascale+ FPGA-board. The characterization will mainly focus on determining the resolution and linearity of both TDCs. A bin merging algorithm is also tested to see the increment of linearity at expense of resolution. The TDL and WU TDL implementations were tested measuring the time difference of two signals obtaining 11.6 ps and 11.4 ps RMS resolution respectively. The achieved performance allow the proposed implementations to be integrated in high-resolution time measuring systems.
Daylight entanglement-based free-space quantum key distribution (QKD) is limited by accidental coincidences from receiver-admitted background light. We develop and experimentally validate a receiver-level framework anchored to measured singles rates and reference coincidence components, linking receiver bandwidth, accepted temporal width, and background-noise density to Bob singles, sifted-key rate, error rate, and quantum bit error rate (QBER) in telecom-wavelength BBM92 QKD. Indoor sweeps show that the sifted-key rate saturates near the source-matched bandwidth, whereas broader bandwidth or higher background mainly increases accidental contamination. Increasing the accepted temporal width leaves Bob singles nearly unchanged but directly raises QBER by enlarging the random-overlap probability. A two-dimensional design map calculated from the model shows that the temporal-window margin contracts rapidly with increasing background-to-signal ratio, while the bandwidth margin remains comparatively broad near source-matched filtering. A rooftop experiment demonstrates daylight operation over a 10 m free-space link, yielding a mean sifted-key rate of 2,811 cps and a mean QBER of 4.43%. This framework provides a quantitative basis for choosing receiver bandwidth and temporal acceptance to meet a target QBER under specified background conditions.
Error correction is a crucial stage in quantum key distribution (QKD) protocols—a promising field of modern cryptography where the secrecy of the shared key information is guaranteed by the laws of quantum mechanics. Currently, there are many effective approaches to error correction in QKD. However, most of them, due to their generic nature, fail to leverage the specific features of particular protocol implementations. This work demonstrates that accounting for the hardware specifics of a QKD system implementing the time-bin protocol enables a significant increase in error correction performance. For the considered QKD system, we have experimentally obtained estimates of the Quantum Bit Error Rate (QBER) observed for each combination of bit and detector. The differences in the obtained estimates reveal that the quantum channel can be modeled as a non-uniform binary channel. Furthermore, based on computational experiments with a model of the quantum channel, it was established that adapting the error correction procedure to its properties can achieve up to a 2.7-fold reduction in the LDPC code decoding failure rate at low error levels.