Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2510.26085 · Physical review. B./Physical review. B

Modeling of simple bandpass filters: Bandwidth broadening of Josephson parametric devices due to non-Markovian coupling to dressed transmission-line modes

Rui Liang Yang, Zheng Shi, Zhirong Lin, Waltraut Wustmann

Published Apr 3, 2026• 0 citations
arXivHTMLPDF

Abstract

Josephson parametric devices are widely used in superconducting quantum computing research but suffer from an inherent gain-bandwidth trade-off. This limitation is partly overcome by coupling the device to its input/output transmission line via a bandpass filter, leading to wider bandwidth at undiminished gain. Here we perform a non-perturbative circuit analysis in terms of dressed transmission-line modes for representative resonant coupling circuits, going beyond the weak-coupling treatment. The strong frequency dependence of the resulting coupling coefficients implies that the Markov approximation commonly employed in cQED analysis is inadequate. By retaining the full frequency dependence of the coupling, we arrive at a non-Markovian form of the quantum Langevin equation with the frequency-dependent complex-valued self-energy of the coupling in place of a single damping parameter. We also consistently generalize the input-output relations and unitarity conditions. Using the exact self-energies of elementary filter networks -- a series- and parallel-LC circuit and a simple representative bandpass filter consisting of their combination -- we calculate the generalized parametric gain factors. Compared with their Markovian counterpart, these gain profiles are strongly modified. We find bandwidth broadening not only in the established parameter regime, where the self-energy of the coupling is in resonance with the device and its real part has unity slope, but also within off-resonant parameter regimes where the real part of the self-energy is large. Our results offer insight for the bandwidth engineering of Josephson parametric devices using simple coupling networks.

DOI
10.1103/zs8r-n36p

Related papers

Comment on "Parametric amplification in Josephson junction embedded transmission lines"

Saptarshi Chaudhuri, Jiansong Gao

Recently Yaakobi and co-workers [Phys. Rev. B 87, 144301 (2013)] theoretically studied four-wave mixing and parametric amplification in a nonlinear transmission line consisting of capacitively shunted Josephson junctions. By deriving and solving the coupled-mode equations, they have arrived at the conclusion that in a wide frequency range around the pump frequency exponential parametric gain (in which the signal grows exponentially with distance) can be achieved. However, we have found a mathematical error in their derivation of the coupled-mode equations (Equation (A13)), which leads to the wrong expression of the gain factor and invalidates their conclusions on the gain and bandwidth. In this comment, we present the correct expression for the parametric gain. We show that for a transmission line with weak dispersion or positive dispersion ($Δk>0 $), as is the case discussed by Yaakobi et al, while quadratic (power) gain can occur around the pump frequency, exponential gain is impossible. Furthermore, for a transmission line with proper intrinsic or engineered dispersion, exponential gain occurs at frequencies where the phase matching condition is met, while around the pump frequency the gain is still quadratic.

arXiv:1308.2951•Aug 13, 2013•3 citations

Parametric Interaction in Josephson Junction Circuits and Transmission Lines

Hamid Reza Mohebbi

This research investigates the realization of parametric amplification in superconducting circuits and structures where nonlinearity is provided by Josephson junction (JJ) elements. We aim to develop a systematic analysis over JJ-based devices toward design of novel traveling-wave Josephson parametric amplifiers (TW-JPA). Chapters of this thesis fall into three categories: lumped JPA, superconducting periodic structures and discrete Josephson transmission lines (DJTL). \nThe unbiased Josephson junction (JJ) is a nonlinear element suitable for parametric amplification through a four-photon process. Two circuit topologies are introduced to capture the unique property of the JJ in order to efficiently mix signal, pump and idler signals for the purpose of signal amplification. Closed-form expressions are derived for gain characteristics, bandwidth determination, noise properties and impedance for this kind of parametric power amplifier. The concept of negative resistance in the gain formulation is observed. A design process is also introduced to find the regimes of operation for gain achievement. Two regimes of operation, oscillation and amplification, are highlighted and distinguished in the result section. Optimization of the circuits to enhance the bandwidth is also carried out. \nMoving toward TW-JPA, the second part is devoted to modelling the linear wave propagation in a periodic superconducting structure. We derive closed-form equations for dispersion and s-parameters of infinite and finite periodic structures, respectively. Band gap formation is highlighted and its potential applications in the design of passive filters and resonators are discussed. The superconducting structures are fabricated using YBCO and measured, illustrating a good correlation with the numerical results. \nA novel superconducting Transmission Line (TL), which is periodically loaded by Josephson junctions (JJ) and assisted by open stubs, is proposed as a platform to realize a traveling-wave parametric device. Using the TL model, this structure is modeled by a system of nonlinear partial differential equations (PDE) with a driving source and mixed-boundary conditions at the input and output terminals, respectively. This model successfully emulates parametric and nonlinear microwave propagation when long-wave approximation is applicable. The influence of dispersion to sustain three non-degenerate phased-locked waves through the TL is highlighted. \nA rigorous and robust Finite Difference Time Domain (FDTD) solver based on the explicit Lax-Wendroff and implicit Crank-Nicolson schemes has been developed to investigate the device responses under various excitations. Linearization of the wave equation, under small-amplitude assumption, dispersion and impedance analysis is performed to explore more aspects of the device for the purpose of efficient design of a traveling-wave parametric amplifier. \nKnowing all microwave characteristics and identifying different regimes of operation, which include impedance properties, cut-off propagation, dispersive behaviour and shock-wave formation, we exploit perturbation theory accompanied by the method of multiple scale to derive the three nonlinear coupled amplitude equations to describe the parametric interaction. A graphical technique is suggested to find three waves on the dispersion diagram satisfying the phase-matching conditions. Both cases of perfect phase-matching and slight mismatching are addressed in this work. The incorporation of two numerical techniques, spectral method in space and multistep Adams-Bashforth in time domain, is employed to monitor the unilateral gain, superior stability and bandwidth of this structure. Two types of functionality, mixing and amplification, with their requirements are described. These properties make this structure desirable for applications ranging from superconducting optoelectronics to dispersive readout of superconducting qubits where high sensitivity and ultra-low noise operation is required.

•May 20, 2011•3 citations

Flux-pumped impedance-engineered broadband Josephson parametric amplifier

Joel Grebel, Audrey Bienfait, Étienne Dumur +7 more

Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.

Applied Physics Letters•Apr 5, 2021•54 citations

The Josephson parametric oscillator - From microscopic studies to single-shot qubit readout

Philip Krantz

Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.

•Jan 1, 2016•4 citations

Many body physics with coupled transmission line resonators

M Leib, M J Hartmann

We present the Josephson junction intersected superconducting transmission line resonator. In contrast to the Josephson parametric amplifier, Josephson bifurcation amplifier and Josephson parametric converter we consider the regime of few microwave photons. We review the derivation of eigenmode frequencies and zero point fluctuations of the nonlinear transmission line resonator and the derivation of the eigenmode Kerr nonlinearities. Remarkably these nonlinearities can reach values comparable to Transmon qubits rendering the device ideal for accessing the strongly correlated regime. This is particularly interesting for investigation of quantum many-body dynamics of interacting particles under the influence of drive and dissipation. We provide current profiles for the device modes and investigate the coupling between resonators in a network of nonlinear transmission line resonators.

arXiv:1208.0134•Physica Scripta•Mar 1, 2013•7 citations

Parametrically pumped superconducting circuits

Philip Krantz

In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model $-$ the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.

•Jan 1, 2013•1 citation
Josephson parametric devices are widely used in superconducting quantum computing research but suffer from an inherent gain-bandwidth trade-off. This limitation is partly overcome by coupling the device to its input/output transmission line via a bandpass filter, leading to wider bandwidth at undiminished gain. Here we perform a non-perturbative circuit analysis in terms of dressed transmission-line modes for representative resonant coupling circuits, going beyond the weak-coupling treatment. The strong frequency dependence of the resulting coupling coefficients implies that the Markov approximation commonly employed in cQED analysis is inadequate. By retaining the full frequency dependence of the coupling, we arrive at a non-Markovian form of the quantum Langevin equation with the frequency-dependent complex-valued self-energy of the coupling in place of a single damping parameter. We also consistently generalize the input-output relations and unitarity conditions. Using the exact self-energies of elementary filter networks -- a series- and parallel-LC circuit and a simple representative bandpass filter consisting of their combination -- we calculate the generalized parametric gain factors. Compared with their Markovian counterpart, these gain profiles are strongly modified. We find bandwidth broadening not only in the established parameter regime, where the self-energy of the coupling is in resonance with the device and its real part has unity slope, but also within off-resonant parameter regimes where the real part of the self-energy is large. Our results offer insight for the bandwidth engineering of Josephson parametric devices using simple coupling networks.
Recently Yaakobi and co-workers [Phys. Rev. B 87, 144301 (2013)] theoretically studied four-wave mixing and parametric amplification in a nonlinear transmission line consisting of capacitively shunted Josephson junctions. By deriving and solving the coupled-mode equations, they have arrived at the conclusion that in a wide frequency range around the pump frequency exponential parametric gain (in which the signal grows exponentially with distance) can be achieved. However, we have found a mathematical error in their derivation of the coupled-mode equations (Equation (A13)), which leads to the wrong expression of the gain factor and invalidates their conclusions on the gain and bandwidth. In this comment, we present the correct expression for the parametric gain. We show that for a transmission line with weak dispersion or positive dispersion ($Δk>0 $), as is the case discussed by Yaakobi et al, while quadratic (power) gain can occur around the pump frequency, exponential gain is impossible. Furthermore, for a transmission line with proper intrinsic or engineered dispersion, exponential gain occurs at frequencies where the phase matching condition is met, while around the pump frequency the gain is still quadratic.
This research investigates the realization of parametric amplification in superconducting circuits and structures where nonlinearity is provided by Josephson junction (JJ) elements. We aim to develop a systematic analysis over JJ-based devices toward design of novel traveling-wave Josephson parametric amplifiers (TW-JPA). Chapters of this thesis fall into three categories: lumped JPA, superconducting periodic structures and discrete Josephson transmission lines (DJTL). \nThe unbiased Josephson junction (JJ) is a nonlinear element suitable for parametric amplification through a four-photon process. Two circuit topologies are introduced to capture the unique property of the JJ in order to efficiently mix signal, pump and idler signals for the purpose of signal amplification. Closed-form expressions are derived for gain characteristics, bandwidth determination, noise properties and impedance for this kind of parametric power amplifier. The concept of negative resistance in the gain formulation is observed. A design process is also introduced to find the regimes of operation for gain achievement. Two regimes of operation, oscillation and amplification, are highlighted and distinguished in the result section. Optimization of the circuits to enhance the bandwidth is also carried out. \nMoving toward TW-JPA, the second part is devoted to modelling the linear wave propagation in a periodic superconducting structure. We derive closed-form equations for dispersion and s-parameters of infinite and finite periodic structures, respectively. Band gap formation is highlighted and its potential applications in the design of passive filters and resonators are discussed. The superconducting structures are fabricated using YBCO and measured, illustrating a good correlation with the numerical results. \nA novel superconducting Transmission Line (TL), which is periodically loaded by Josephson junctions (JJ) and assisted by open stubs, is proposed as a platform to realize a traveling-wave parametric device. Using the TL model, this structure is modeled by a system of nonlinear partial differential equations (PDE) with a driving source and mixed-boundary conditions at the input and output terminals, respectively. This model successfully emulates parametric and nonlinear microwave propagation when long-wave approximation is applicable. The influence of dispersion to sustain three non-degenerate phased-locked waves through the TL is highlighted. \nA rigorous and robust Finite Difference Time Domain (FDTD) solver based on the explicit Lax-Wendroff and implicit Crank-Nicolson schemes has been developed to investigate the device responses under various excitations. Linearization of the wave equation, under small-amplitude assumption, dispersion and impedance analysis is performed to explore more aspects of the device for the purpose of efficient design of a traveling-wave parametric amplifier. \nKnowing all microwave characteristics and identifying different regimes of operation, which include impedance properties, cut-off propagation, dispersive behaviour and shock-wave formation, we exploit perturbation theory accompanied by the method of multiple scale to derive the three nonlinear coupled amplitude equations to describe the parametric interaction. A graphical technique is suggested to find three waves on the dispersion diagram satisfying the phase-matching conditions. Both cases of perfect phase-matching and slight mismatching are addressed in this work. The incorporation of two numerical techniques, spectral method in space and multistep Adams-Bashforth in time domain, is employed to monitor the unilateral gain, superior stability and bandwidth of this structure. Two types of functionality, mixing and amplification, with their requirements are described. These properties make this structure desirable for applications ranging from superconducting optoelectronics to dispersive readout of superconducting qubits where high sensitivity and ultra-low noise operation is required.
Broadband quantum-limited amplifiers play a critical role in the single-shot readout of superconducting qubits, but a popular implementation, the traveling wave parametric amplifier, involves a complex design and fabrication process. Here, we present a simple design for a Josephson parametric amplifier, using a lumped element resonator comprising a superconducting quantum interference device whose useful bandwidth is enhanced with an on-chip impedance-matching circuit. We demonstrate a flux-coupling geometry that maximizes the coupling to the Josephson loop and minimizes spurious excitation of the amplifier resonant circuit. The amplifier, which operates in a flux-pumped mode, is demonstrated with a power gain of more than 20 dB over a bandwidth of about 300 MHz, where approximate noise measurements indicate quantum-limited performance. A procedure is given for optimizing the bandwidth for this kind of amplifier, using a linearized circuit simulation while minimizing non-linearities.
Circuit quantum electrodynamics (cQED) is a prominent platform for quantum information processing, in which microwave photons are confined into resonant cavities coupled to superconducting quantum bits (qubits). The large effective dipole moment of the qubit, in combination with the high energy density of the quasi 1-D resonator allow these systems to enter the so-called strong coupling regime. The quantum state of the qubit can then be assessed by probing the frequency of the resonator, protecting the qubit from otherwise losing its energy to the environment. However, eventhough this so-called dispersive readout technique has proven useful, it is often in itself insufficient to render single-shot readout performance | one of the crucial tasks required for realizing a quantum computer. This thesis describes the demonstration of a single-shot readout technique forsuperconducting quantum bits, based on coupling the qubit to a frequency-tunable resonator. The backbone of our device is a 5 GHz quarter-wavelength coplanar waveguide resonator, terminated at one end by a non-linear inductance provided by a superconducting quantum interference device (SQUID). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using an on-chip transmission line. The modulation occurs on a timescale much faster than the photon loss out of the resonator and if the pump strength exceeds a threshold value set by the damping rate of the resonator, an intense photon field will build up inside the resonator | known as "parametric oscillations". By heterodyne detection of the output signal from the Josephson parametric oscillator (JPO), we first extracted two leading nonlinear effects of the system (dominating in different limits of applied magnetic flux). Next, we couple a qubit to the JPO and demonstrate that we can encode its quantum state onto the strong output field of the parametric oscillator (or lack thereof), rendering a signal-to-noise ratio sufficient for single-shot state detection and therefore also obviating a quantum limited parametric amplifier. The thesis also contains results from microscopic studies of the Josephson junctions, which we use to provide the necessary nonlinearities in the above mentioned devices. In particular, we show how the microstructure of the barrier layer and its atomic composition can be used to infer important electrical properties of the junctions. This knowledge allows us to better tailor the properties of Josephson-based devices.
We present the Josephson junction intersected superconducting transmission line resonator. In contrast to the Josephson parametric amplifier, Josephson bifurcation amplifier and Josephson parametric converter we consider the regime of few microwave photons. We review the derivation of eigenmode frequencies and zero point fluctuations of the nonlinear transmission line resonator and the derivation of the eigenmode Kerr nonlinearities. Remarkably these nonlinearities can reach values comparable to Transmon qubits rendering the device ideal for accessing the strongly correlated regime. This is particularly interesting for investigation of quantum many-body dynamics of interacting particles under the influence of drive and dissipation. We provide current profiles for the device modes and investigate the coupling between resonators in a network of nonlinear transmission line resonators.
In this licentiate thesis, I present the design, fabrication, and characterization of superconducting parametric resonators, for use in quantum information processing. These devices are quarter-wavelength coplanar waveguide resonators (~5 GHz), terminated at one end by a non-linear inductance provided by a SQUID (superconducting quantum interference device). The SQUID acts as a flux-controlled boundary condition, which effectively changes the electrical length of the resonator. This enables the modulation of the resonant frequency by coupling microwave magnetic flux into the SQUID, using on-chip transmission lines. The modulation occurs on a timescale much faster than the photon loss out of the resonator. The non-linearity provides several different regimes for operating this device. I focused on the parametric regime, in which the non-linear element was being modulated (pumped) at or near twice the resonant frequency. This pumping can lead to amplification and frequency conversion of an incoming signal. It can also give rise to instabilities and self-oscillations "parametric oscillations" - that is, the generation of an intense electric field in the resonator (the creation of photons). Parametric oscillations set in when the pumping strength exceeds a threshold value, and also depends on the pump-frequency detuning from twice the resonance and on the static flux through the SQUID. I characterized the devices over a wide parameter range by doing homodyne detection of the reflected signal or of the emitted field oscillations. In particular, I investigated the damping and two leading nonlinearities, dominating in different operating regimes, which influence the dynamics of the parametric resonator. First, I extracted the Duffing nonlinearity by studying the line width of the resonator as a function of the input signal (without pumping the SQUID). Second, with high pump amplitude, I extracted the pump-induced nonlinearity by determining the threshold parameters (pump amplitude and detuning) for the onset of parametric oscillations; this nonlinearity leads to the generation of higher-order pump terms that complicate the system dynamics, but can be mitigated now that they have been understood. My results validate a recent theoretical model for the classical, non-linear dynamics of parametric resonance, and helps determine workable design parameters. Finally, I helped develop a linearized model −-− the "pumpistor" - describing this device in terms of a flux-controlled impedance. This will be useful when designing more complex circuits. One goal of this work is to demonstrate single-shot measurements on superconducting qubits (quantum bits of information). We will use the parametric resonator as a threshold discriminator, associating the qubit's two energy eigenstates with the parametric oscillations either turning on or not. This would be a very useful device in the quantum engineer's toolbox when designing systems for quantum information processing and communication.