Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2509.23569 · IEEE Transactions on Applied Superconductivity

Microwave SQUID Multiplexer Readout Performance Using a Direct-RF RFSoC-Based Software-Defined Radio

Manuel Elías García Redondo, J. Bonilla-Neira, Nahuel Agustín Müller, Luciano Pablo Ferreyro, J.M. Geria, Timo Muscheid, R. Gartmann, Alejandro Almela, Matías Rolf Hampel, L.E. Ardila-Perez, Mathias Wegner, M. Platino, O. Sander, Sebastian Kempf, M. Weber

Published Mar 31, 2026• 0 citations
arXivHTMLPDF

Abstract

In this work, we report the experimental readout results of a$µ$MUX device using a Direct-RF Software-Defined Radio (SDR) prototype based on the ZCU216 Radio-Frequency System-on-Chip (RFSoC) evaluation board. First, the Direct-RF SDR architecture is described. Then, the analog performance of the SDR system was characterized both in loopback and when coupled to the cryogenic multiplexing system to evaluate the noise contributions of the SDR readout system. Later, the SDR system performance was optimized for$µ$MUX readout, focusing on bolometric applications. Finally, the minimum demodulated flux noise was obtained through the optimally conditioned readout of a$µ$MUX channel. The results obtained showed a minimum demodulated white flux noise of$\approx 4 \mu \Phi _{0}/\sqrt{Hz}$in both demodulation domains (i.e. amplitude$\gamma$and resonator phase$\theta$) and dominated by the cryogenic microwave chain noise temperature of$T_{n}^{cryo}=4.6$K. These results are comparable to those obtained with traditional SDR architectures and demonstrate that the Direct-RF SDR prototype is suitable for the readout of$µ$MUX devices.

DOI
10.1109/tasc.2026.3679166

Related papers

RFSoC Gen3-Based Software-Defined Radio Characterization for the Readout System of Low-Temperature Bolometers

Manuel Elías García Redondo, Timo Muscheid, R. Gartmann +14 more

Abstract This work reports the performance evaluation of an SDR readout system based on the latest generation (Gen3) of AMD’s Radio-Frequency System-on-Chip (RFSoC) processing platform, which integrates a full-stack processing system and a powerful FPGA with up to 32 high-speed and high-resolution 14-bit Digital-to-Analog Converters and 14-bit Analog-to-Digital Converters. The proposed readout system uses a previously developed multi-band, double-conversion IQ RF-mixing board targeting a multiplexing factor of approximately 1000 bolometers in a bandwidth between 4 and 8 GHz, in line with state-of-the-art microwave SQUID multiplexers. The characterization of the system was performed in two stages, under the conditions typically imposed by the multiplexer and the cold readout circuit: first, in transmission, showing that noise and spurious levels of the generated tones are close to the values imposed by the cold readout, and second, in RF loopback, presenting noise values better than −100 dBc/Hz totally in agreement with the state-of-the-art readout systems. It was demonstrated that the RFSoC Gen3 device is a suitable enabling technology for the next generation of superconducting detector readout systems, reducing system complexity, increasing system integration, and achieving these goals without performance degradation.

arXiv:2311.03480•Journal of Low Temperature Physics•Apr 12, 2024•8 citations

Optimal demodulation domain for microwave SQUID multiplexers in presence of readout system noise

Manuel Elías García Redondo, Nahuel Agustín Müller, J. M. Salum +15 more

The Microwave SQUID Multiplexer (μMUX) is the device of choice for the readout of a large number of low-temperature detectors in a wide variety of experiments within the fields of astronomy and particle physics. While it offers large multiplexing factors, the system noise performance is highly dependent on the cold- and warm-readout electronic systems used to read it out, as well as the demodulation domain and parameters chosen. In order to understand the impact of the readout systems in the overall detection system noise performance, first, we extended the available μMUX simulation frameworks, including additive and multiplicative noise sources in the probing tones (i.e., phase and amplitude noise), along with the capability of demodulating the scientific data, either in the resonator’s phase or the scattering amplitude. Then, considering the additive noise as a dominant noise source, the optimum readout parameters to achieve minimum system noise were found for both open-loop and flux-ramp demodulation schemes in the aforementioned domains. Later, we evaluated the system noise sensitivity to multiplicative noise sources under the optimum readout parameters. Finally, as a case study, we evaluated the optimal demodulation domain and the expected system noise level for a typical software-defined radio readout system. This work leads to an improved system performance prediction and noise engineering based on the available readout electronics and the selected demodulation domain.

arXiv:2406.06782•Journal of Applied Physics•Sep 19, 2024•4 citations

Full-Scale Microwave SQUID Multiplexer Readout System for Magnetic Microcalorimeters

M. Neidig, Timo Muscheid, R. Gartmann +4 more

The deployment of large cryogenic detector arrays, comprising hundreds to thousands of individual detectors, is highly beneficial for various cutting-edge applications, requiring large statistics, angular resolution or imaging capabilities. The readout of such arrays, however, presents a major challenge in terms of system complexity, parasitic heat load, and cost, which can be overcome only through multiplexing. Among the various multiplexing approaches, microwave SQUID multiplexing ($\mathrm{\mu }$MUXing) currently represents the state of the art, in particular for magnetic microcalorimeter (MMC) readout. In this work, we demonstrate the successful operation of the latest generation of our microwave SQUID multiplexer-based readout system, based on a SQUID multiplexer tailored for MMC readout and a custom full-scale software-defined radio (SDR) electronics, capable of handling up to 400 channels. We operate 14 readout channels simultaneously and demonstrate that the system operates reliably across the entire 4-8 GHz frequency band and achieves low flux white noise levels of$(1.4\pm 0.2)\,\mathrm{\upmu\Phi _{0}/\sqrt{Hz}}$in flux-ramp-demodulated readout. While technical steps regarding the SDR output power, as well as a demonstration of the simultaneous readout of the full 400 channels, remain, our results confirm that our system is fully functional and provides a scalable path towards future large-scale, high-resolution MMC experiments.

arXiv:2509.07671•IEEE Transactions on Applied Superconductivity•May 22, 2026•4 citations

Characterization of the RF Board for microwave SQUID multiplexing readout electronics

Junbo Wang, Jianing Dong, Zhekai Cheng +1 more

Microwave SQUID multiplexing ($μ$MUX) is a widely used readout technique for large-scale transition-edge sensor (TES) arrays. It uses radio-frequency (RF) probe tones to interrogate cryogenic resonators, requiring frequency conversion between the baseband electronics and the cryogenic RF signal chain. This work describes the RF Board, a room-temperature frequency-conversion board deployed in the AliCPT $μ$MUX readout system. The board up-converts 0-4 GHz baseband I/Q signals to the 4-8 GHz RF band for injection into the cryogenic chain and down-converts returned RF signals to baseband I/Q for ADC digitization. For the current 1000-tone operation, with a DAC output tone power of -30 dBm/tone, the required power windows are -35 to -25 dBm/tone for the RF tones transmitted to the cryostat and -45 to -35 dBm/tone at the ADC input for the returned tones. The RF Board is characterized using swept single-tone measurements covering up-conversion, down-conversion, and RF loopback. Based on these measurements, the RF output power is calculated to be -31.06 to -25.53 dBm, satisfying the RF output window. Assuming a representative cryogenic-chain transmission of -40 dB, the loopback result gives an estimated returned power of -45 to -35 dBm, within the target range. These results show that the RF Board meets the wideband frequency-conversion and tone-power requirements for the $μ$MUX readout system.

arXiv:2606.28901•Jun 27, 2026•0 citations

Prototype of the room-temperature readout system for microwave multiplexing readout of transition edge sensor

Yuanda Wang, Cao Ping, Weigang Yin +8 more

Transition Edge Sensors (TESs) are highly sensitive cryogenic detectors widely used in astronomy, high-energy physics and nuclear radiation detection. As TES is increasingly deployed in large-scale arrays to improve sensitivity and effective collecting area, multiplexed readout becomes essential for reducing system complexity. Microwave SQUID multiplexing (μMUX) technology combining superconducting resonators with radio-frequency superconducting quantum interference devices (RF-SQUIDs), represents a state-of-the-art solution. In this work, a room-temperature readout prototype for TES μMUX readout was designed. The system features a scalable two-stage architecture, including a highly integrated, chassis-independent front-end signal processing module and back-end event-reconstruction module. A high-frequency-resolution frequency-comb signal generation method with real-time, per-tone frequency and phase tunability was developed. In addition, optimization of the firmware implementation effectively overcomes the computational-resource bottleneck of the Field Programmable Gate Array (FPGA). The prototype supports autonomous frequency sweeping, parameter diagnostics, and online event reconstruction. Self-test shows S 21 phase noise better than −110 dBc/Hz at −30 dBm, remaining stable with increasing channel count. Joint tests with a μMUX cryogenic system successfully captured the RF-SQUID response and achieved an equivalent noise current of 44 pA/√Hz referred to the TES, validating the prototype as a practical solution of the room-temperature system for TES μMUX readout.

Nuclear Engineering and Technology•Oct 30, 2026•0 citations

White noise of Nb-based microwave superconducting quantum interference device multiplexers with NbN coplanar resonators for readout of transition edge sensors

Satoshi Kohjiro, Fuminori Hirayama, Hirotake Yamamori +3 more

White noise of dissipationless microwave radio frequency superconducting quantum interference device (RF-SQUID) multiplexers has been experimentally studied to evaluate their readout performance for transition edge sensor (TES) photon counters ranging from near infrared to gamma ray. The characterization has been carried out at 4 K, first to avoid the low-frequency fluctuations present at around 0.1 K, and second, for a feasibility study of readout operation at 4 K for extended applications. To increase the resonant Q at 4 K and maintain low noise SQUID operation, multiplexer chips consisting of niobium nitride (NbN)-based coplanar-waveguide resonators and niobium (Nb)-based RF-SQUIDs have been developed. This hybrid multiplexer exhibited 1 × 104 ≤ Q ≤ 2 × 104 and the square root of spectral density of current noise referred to the SQUID input √SI = 31 pA/√Hz. The former and the latter are factor-of-five and seven improvements from our previous results on Nb-based resonators, respectively. Two-directional readout on the complex plane of the transmission component of scattering matrix S21 enables us to distinguish the flux noise from noise originating from other sources, such as the cryogenic high electron mobility transistor (HEMT) amplifier. Systematic noise measurements with various microwave readout powers PMR make it possible to distinguish the contribution of noise sources within the system as follows: (1) The achieved √SI is dominated by the Nyquist noise from a resistor at 4 K in parallel to the SQUID input coil which is present to prevent microwave leakage to the TES. (2) The next dominant source is either the HEMT-amplifier noise (for small values of PMR) or the quantization noise due to the resolution of 300-K electronics (for large values of PMR). By a decrease of these noise levels to a degree that is achievable by current technology, we predict that the microwave RF-SQUID multiplexer can exhibit √SI ≤ 5 pA/√Hz, i.e., close to √SI of state-of-the-art DC-SQUID-based multiplexers.

Journal of Applied Physics•Jun 10, 2014•18 citations
In this work, we report the experimental readout results of aµµµMUX device using a Direct-RF Software-Defined Radio (SDR) prototype based on the ZCU216 Radio-Frequency System-on-Chip (RFSoC) evaluation board. First, the Direct-RF SDR architecture is described. Then, the analog performance of the SDR system was characterized both in loopback and when coupled to the cryogenic multiplexing system to evaluate the noise contributions of the SDR readout system. Later, the SDR system performance was optimized forµµµMUX readout, focusing on bolometric applications. Finally, the minimum demodulated flux noise was obtained through the optimally conditioned readout of aµµµMUX channel. The results obtained showed a minimum demodulated white flux noise of≈4μΦ0/Hz\approx 4 \mu \Phi _{0}/\sqrt{Hz}≈4μΦ0​/Hz​in both demodulation domains (i.e. amplitudeγ\gammaγand resonator phaseθ\thetaθ) and dominated by the cryogenic microwave chain noise temperature ofTncryo=4.6T_{n}^{cryo}=4.6Tncryo​=4.6K. These results are comparable to those obtained with traditional SDR architectures and demonstrate that the Direct-RF SDR prototype is suitable for the readout ofµµµMUX devices.
Abstract This work reports the performance evaluation of an SDR readout system based on the latest generation (Gen3) of AMD’s Radio-Frequency System-on-Chip (RFSoC) processing platform, which integrates a full-stack processing system and a powerful FPGA with up to 32 high-speed and high-resolution 14-bit Digital-to-Analog Converters and 14-bit Analog-to-Digital Converters. The proposed readout system uses a previously developed multi-band, double-conversion IQ RF-mixing board targeting a multiplexing factor of approximately 1000 bolometers in a bandwidth between 4 and 8 GHz, in line with state-of-the-art microwave SQUID multiplexers. The characterization of the system was performed in two stages, under the conditions typically imposed by the multiplexer and the cold readout circuit: first, in transmission, showing that noise and spurious levels of the generated tones are close to the values imposed by the cold readout, and second, in RF loopback, presenting noise values better than −100 dBc/Hz totally in agreement with the state-of-the-art readout systems. It was demonstrated that the RFSoC Gen3 device is a suitable enabling technology for the next generation of superconducting detector readout systems, reducing system complexity, increasing system integration, and achieving these goals without performance degradation.
The Microwave SQUID Multiplexer (μMUX) is the device of choice for the readout of a large number of low-temperature detectors in a wide variety of experiments within the fields of astronomy and particle physics. While it offers large multiplexing factors, the system noise performance is highly dependent on the cold- and warm-readout electronic systems used to read it out, as well as the demodulation domain and parameters chosen. In order to understand the impact of the readout systems in the overall detection system noise performance, first, we extended the available μMUX simulation frameworks, including additive and multiplicative noise sources in the probing tones (i.e., phase and amplitude noise), along with the capability of demodulating the scientific data, either in the resonator’s phase or the scattering amplitude. Then, considering the additive noise as a dominant noise source, the optimum readout parameters to achieve minimum system noise were found for both open-loop and flux-ramp demodulation schemes in the aforementioned domains. Later, we evaluated the system noise sensitivity to multiplicative noise sources under the optimum readout parameters. Finally, as a case study, we evaluated the optimal demodulation domain and the expected system noise level for a typical software-defined radio readout system. This work leads to an improved system performance prediction and noise engineering based on the available readout electronics and the selected demodulation domain.
The deployment of large cryogenic detector arrays, comprising hundreds to thousands of individual detectors, is highly beneficial for various cutting-edge applications, requiring large statistics, angular resolution or imaging capabilities. The readout of such arrays, however, presents a major challenge in terms of system complexity, parasitic heat load, and cost, which can be overcome only through multiplexing. Among the various multiplexing approaches, microwave SQUID multiplexing (μ\mathrm{\mu }μMUXing) currently represents the state of the art, in particular for magnetic microcalorimeter (MMC) readout. In this work, we demonstrate the successful operation of the latest generation of our microwave SQUID multiplexer-based readout system, based on a SQUID multiplexer tailored for MMC readout and a custom full-scale software-defined radio (SDR) electronics, capable of handling up to 400 channels. We operate 14 readout channels simultaneously and demonstrate that the system operates reliably across the entire 4-8 GHz frequency band and achieves low flux white noise levels of$(1.4\pm 0.2)\,\mathrm{\upmu\Phi _{0}/\sqrt{Hz}}$in flux-ramp-demodulated readout. While technical steps regarding the SDR output power, as well as a demonstration of the simultaneous readout of the full 400 channels, remain, our results confirm that our system is fully functional and provides a scalable path towards future large-scale, high-resolution MMC experiments.
Microwave SQUID multiplexing (μμμMUX) is a widely used readout technique for large-scale transition-edge sensor (TES) arrays. It uses radio-frequency (RF) probe tones to interrogate cryogenic resonators, requiring frequency conversion between the baseband electronics and the cryogenic RF signal chain. This work describes the RF Board, a room-temperature frequency-conversion board deployed in the AliCPT μμμMUX readout system. The board up-converts 0-4 GHz baseband I/Q signals to the 4-8 GHz RF band for injection into the cryogenic chain and down-converts returned RF signals to baseband I/Q for ADC digitization. For the current 1000-tone operation, with a DAC output tone power of -30 dBm/tone, the required power windows are -35 to -25 dBm/tone for the RF tones transmitted to the cryostat and -45 to -35 dBm/tone at the ADC input for the returned tones. The RF Board is characterized using swept single-tone measurements covering up-conversion, down-conversion, and RF loopback. Based on these measurements, the RF output power is calculated to be -31.06 to -25.53 dBm, satisfying the RF output window. Assuming a representative cryogenic-chain transmission of -40 dB, the loopback result gives an estimated returned power of -45 to -35 dBm, within the target range. These results show that the RF Board meets the wideband frequency-conversion and tone-power requirements for the μμμMUX readout system.
Transition Edge Sensors (TESs) are highly sensitive cryogenic detectors widely used in astronomy, high-energy physics and nuclear radiation detection. As TES is increasingly deployed in large-scale arrays to improve sensitivity and effective collecting area, multiplexed readout becomes essential for reducing system complexity. Microwave SQUID multiplexing (μMUX) technology combining superconducting resonators with radio-frequency superconducting quantum interference devices (RF-SQUIDs), represents a state-of-the-art solution. In this work, a room-temperature readout prototype for TES μMUX readout was designed. The system features a scalable two-stage architecture, including a highly integrated, chassis-independent front-end signal processing module and back-end event-reconstruction module. A high-frequency-resolution frequency-comb signal generation method with real-time, per-tone frequency and phase tunability was developed. In addition, optimization of the firmware implementation effectively overcomes the computational-resource bottleneck of the Field Programmable Gate Array (FPGA). The prototype supports autonomous frequency sweeping, parameter diagnostics, and online event reconstruction. Self-test shows S 21 phase noise better than −110 dBc/Hz at −30 dBm, remaining stable with increasing channel count. Joint tests with a μMUX cryogenic system successfully captured the RF-SQUID response and achieved an equivalent noise current of 44 pA/√Hz referred to the TES, validating the prototype as a practical solution of the room-temperature system for TES μMUX readout.
White noise of dissipationless microwave radio frequency superconducting quantum interference device (RF-SQUID) multiplexers has been experimentally studied to evaluate their readout performance for transition edge sensor (TES) photon counters ranging from near infrared to gamma ray. The characterization has been carried out at 4 K, first to avoid the low-frequency fluctuations present at around 0.1 K, and second, for a feasibility study of readout operation at 4 K for extended applications. To increase the resonant Q at 4 K and maintain low noise SQUID operation, multiplexer chips consisting of niobium nitride (NbN)-based coplanar-waveguide resonators and niobium (Nb)-based RF-SQUIDs have been developed. This hybrid multiplexer exhibited 1 × 104 ≤ Q ≤ 2 × 104 and the square root of spectral density of current noise referred to the SQUID input √SI = 31 pA/√Hz. The former and the latter are factor-of-five and seven improvements from our previous results on Nb-based resonators, respectively. Two-directional readout on the complex plane of the transmission component of scattering matrix S21 enables us to distinguish the flux noise from noise originating from other sources, such as the cryogenic high electron mobility transistor (HEMT) amplifier. Systematic noise measurements with various microwave readout powers PMR make it possible to distinguish the contribution of noise sources within the system as follows: (1) The achieved √SI is dominated by the Nyquist noise from a resistor at 4 K in parallel to the SQUID input coil which is present to prevent microwave leakage to the TES. (2) The next dominant source is either the HEMT-amplifier noise (for small values of PMR) or the quantization noise due to the resolution of 300-K electronics (for large values of PMR). By a decrease of these noise levels to a degree that is achievable by current technology, we predict that the microwave RF-SQUID multiplexer can exhibit √SI ≤ 5 pA/√Hz, i.e., close to √SI of state-of-the-art DC-SQUID-based multiplexers.