Operating superconducting qubits at elevated temperatures offers increased cooling power, thus system scalability, but requires suppression of thermal photons to preserve coherence and readout fidelity. This motivates migration to higher operation frequencies, which demands high-frequency amplification with near-quantum-limited noise characteristics for qubit readout. Here, we report the design and experimental realization of a wireless Josephson parametric amplifier (WJPA) operating above 20 GHz. The wireless design eliminates losses and impedance mismatches that become problematic at high frequencies. The WJPA achieves more than 20 dB of gain across a tunable frequency range of 21–23.5 GHz, with a typical 3 dB bandwidth of 3 MHz. Through Y-factor measurements and a qubit-based photon number calibration, we show that the amplifier exhibits an added noise of approximately two photons.
Operating superconducting qubits at elevated temperatures offers increased cooling power, thus system scalability, but requires suppression of thermal photons to preserve coherence and readout fidelity. This motivates migration to higher operation frequencies, which demands high-frequency amplification with near-quantum-limited noise characteristics for qubit readout. Here, we report the design and experimental realization of a wireless Josephson parametric amplifier (WJPA) operating above 20 GHz. The wireless design eliminates losses and impedance mismatches that become problematic at high frequencies. The WJPA achieves more than 20 dB of gain across a tunable frequency range of 21–23.5 GHz, with a typical 3 dB bandwidth of 3 MHz. Through Y-factor measurements and a qubit-based photon number calibration, we show that the amplifier exhibits an added noise of approximately two photons.
Josephson junction parametric amplifiers are playing a crucial role in the readout chain in superconducting quantum information experiments. However, their integration with current 3D cavity implementations poses the problem of transitioning between waveguide, coax cables, and planar circuits. Moreover, Josephson amplifiers require auxiliary microwave components, like directional couplers and/or hybrids, that are sources of spurious losses and impedance mismatches that limit measurement efficiency and amplifier tunability. We have developed a wireless architecture for these parametric amplifiers that eliminates superfluous microwave components and interconnects. This greatly simplifies their assembly and integration into experiments. We present an experimental realization of such a device operating in the 9–11 GHz band with about 100 MHz of amplitude gain-bandwidth product, on par with devices mounted in conventional sample holders. The simpler impedance environment presented to the amplifier also results in increased amplifier tunability.
Bringing signals from quantum to classical, from few-photon to many-photon levels for further processing, is a common challenge in rising quantum technologies. These include quantum computing, quantum communication, quantum sensing, radio astronomy, and dark matter searches, typically operating at microwave frequencies and millikelvin temperatures. Superconducting parametric amplifiers, as the first piece in the readout chain, have become a cornerstone of these technologies, since they offer unrivaled noise performance near the quantum-mechanical limit and high gain to surpass the noise of subsequent amplifiers. A notable implementation is the Josephson traveling-wave parametric amplifier (TWPA), which stands out due to its bandwidth of several Gigahertz and high saturation power, often larger than -100 dBm. These key properties come at the cost of complexity in design and fabrication: TWPA metamaterials often contain several thousands of Josephson junctions. Designing high-gain TWPAs involves three major challenges: ensuring impedance-matching, phase-matching of parametric amplification, and suppressing unwanted processes, all achievable through sub-wavelength dispersion engineering. This thesis covers the circuit design and analysis, implementation, and experimental characterization of a dispersion-engineered TWPA based on radio-frequency superconducting interference devices (rf-SQUIDs). It focuses on a detailed investigation of dispersion-engineering techniques and their effects on amplifier performance, particularly through the use of time-domain circuit simulations to analyze the multimode dynamics of the circuit. The experimentally realized device features 18 dB of gain, an instantaneous bandwidth spanning from 2.2 to 6.7 GHz, a system noise of 2.5 quanta, and a saturation power of (−86.5 ± 4.0) dBm. With these characteristics, it is suitable for frequency-multiplexed readout of detector arrays or qubits. Its high saturation power, about 10 dB higher than other reported Josephson-junction-based TWPAs, allows increasing the number of qubits per readout line, or decreasing the intermodulation between frequency-multiplexed qubits, both crucial for scaling up quantum computation.
We demonstrate a Josephson parametric amplifier design with a band-pass impedance-matching network based on a third-order Chebyshev prototype. We measured eight amplifiers operating at 4.6 GHz that exhibit gains of 20 dB with less than 1-dB gain ripple and bandwidth up to 500 MHz. The amplifiers further achieve high-output-saturation powers around $\ensuremath{-}73\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$ based on the use of rf superconducting quantum interference device arrays as their nonlinear element. We characterize the system readout efficiency and its signal-to-noise ratio near saturation using a Sycamore processor, finding the data consistent with near quantum limited noise performance of the amplifiers. In addition, we measure the amplifiers' intermodulation distortion in two-tone experiments as a function of input power and intertone detuning, and observe excess distortion at small detuning with a pronounced dip as a function of signal power, which we interpret in terms of power-dependent dielectric losses.
We introduce a near-quantum-limited amplifier with a large tunable bandwidth and high dynamic range---the Josephson array-mode parametric amplifier (JAMPA). The signal and idler modes involved in the amplification process are realized by the array modes of a chain of 1000 flux-tunable Josephson-junction-based nonlinear elements. The frequency spacing between the array modes is comparable to the flux tunability of the modes, ensuring that any desired frequency can be occupied by a resonant mode, which can further be pumped to produce high gain. We experimentally demonstrate that the device can be operated as a nearly quantum-limited parametric amplifier with 20 dB of gain at almost any frequency within a 4--12-GHz band. On average, it has a 3-dB bandwidth of 11 MHz and an input 1-dB compression power of $\ensuremath{-}108\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$, which can go as high as $\ensuremath{-}93\phantom{\rule{0.2em}{0ex}}\mathrm{dBm}$. We envision the application of such a device to the time- and frequency-multiplexed readout of multiple qubits, as well as to the generation of continuous-variable cluster states.
Advancing superconducting quantum devices to higher operating frequencies broadens their functionality and enables operation at elevated temperatures, but it also requires near-quantum-limited amplifiers beyond the few-gigahertz regime. Here we present a junction-free, kinetic-inductance parametric amplifier based on thin-film niobium nitride (NbN) operating at 23 GHz in the microwave K-band, achieving a gain up to 40 dB, a 100 MHz gain-bandwidth product, a 1 dB saturation input power of -85 dBm with 23 dB gain, and added noise no greater than 1.4 quanta for phase-preserving amplification. Leveraging the large superconducting gap of NbN, this architecture can be extended to even higher frequencies, supporting applications such as high-fidelity readout of millimeter-wave superconducting qubits and axion searches over an expanded mass window.
We demonstrate a high dynamic range Josephson parametric amplifier (JPA) in which the active nonlinear element is implemented using an array of rf-SQUIDs. The device is matched to the 50 Ω environment with a Klopfenstein-taper impedance transformer and achieves a bandwidth of 250–300 MHz with input saturation powers up to −95 dBm at 20 dB gain. A 54-qubit Sycamore processor was used to benchmark these devices, providing a calibration for readout power, an estimation of amplifier added noise, and a platform for comparison against standard impedance matched parametric amplifiers with a single dc-SQUID. We find that the high power rf-SQUID array design has no adverse effect on system noise, readout fidelity, or qubit dephasing, and we estimate an upper bound on amplifier added noise at 1.6 times the quantum limit. Finally, amplifiers with this design show no degradation in readout fidelity due to gain compression, which can occur in multi-tone multiplexed readout with traditional JPAs.