Portable quantum technologies require robust lightweight apparatus with superior performance. For techniques dependent upon high-vacuum environments, such as atom interferometers and atomic clocks, three-dimensional (3D) printing enables additional avenues to tailor in-vacuum gas propagation dynamics. We demonstrate intricate fine-scale surface patterning of 3D-printed vacuum components to increase the rate at which gas particles collide with the surface. By applying a nonevaporable getter coating for use as a surface pump, we show that the patterned surface pumps gas particles 3.8 times faster than equivalent flat areas. These patterns can be directly integrated into additively manufactured components, enabling application in close proximity to key experimental regions and contributing to overall mass reduction. We develop numerical simulations that show good agreement with this result and predict up to a tenfold increase in the pumping rate, for realistic surface structures. Our work has direct applications in enabling passively pumped portable quantum technologies but also establishes 3D printing as a powerful technique for the creation of optimized surface patterning to provide enhanced control over high-vacuum gas dynamics for a broad range of applications.
Portable quantum technologies require robust lightweight apparatus with superior performance. For techniques dependent upon high-vacuum environments, such as atom interferometers and atomic clocks, three-dimensional (3D) printing enables additional avenues to tailor in-vacuum gas propagation dynamics. We demonstrate intricate fine-scale surface patterning of 3D-printed vacuum components to increase the rate at which gas particles collide with the surface. By applying a nonevaporable getter coating for use as a surface pump, we show that the patterned surface pumps gas particles 3.8 times faster than equivalent flat areas. These patterns can be directly integrated into additively manufactured components, enabling application in close proximity to key experimental regions and contributing to overall mass reduction. We develop numerical simulations that show good agreement with this result and predict up to a tenfold increase in the pumping rate, for realistic surface structures. Our work has direct applications in enabling passively pumped portable quantum technologies but also establishes 3D printing as a powerful technique for the creation of optimized surface patterning to provide enhanced control over high-vacuum gas dynamics for a broad range of applications.
Abstract The development of quantum technology has opened up exciting opportunities to revolutionize computing and communication, timing and navigation systems, enable noninvasive imaging of the human body, and probe fundamental physics with unprecedented precision. Alongside these advancements has come an increase in experimental complexity and a correspondingly greater dependence on compact, efficient and reliable hardware. The drive to move quantum technologies from laboratory prototypes to portable, real‐world instruments has incentivized miniaturization of experimental systems relating to a strong demand for smaller, more robust, and less power‐hungry quantum hardware and for increasingly specialized and intricate components. Additive manufacturing, already heralded as game‐changing for many manufacturing sectors, is especially well‐suited to this task owing to the comparatively large amount of design freedom it enables and its ability to produce intricate 3D forms and specialized components. Herein we review work conducted to date on the application of additive manufacturing to quantum technologies, discuss the current state of the art in additive manufacturing in optics, optomechanics, magnetic components and vacuum equipment, and consider pathways for future advancement. We also give an overview of the research and application areas most likely to be impacted by the deployment of additive manufacturing techniques within the quantum technology sector.
Abstract Recent advances in the understanding and control of quantum technologies, such as those based on cold atoms, have resulted in devices with extraordinary metrological performance. To realise this potential outside of a lab environment the size, weight and power consumption need to be reduced. Here we demonstrate the use of laser powder bed fusion, an additive manufacturing technique, as a production technique relevant to the manufacture of quantum sensors. As a demonstration we have constructed two key components using additive manufacturing, namely magnetic shielding and vacuum chambers. The initial prototypes for magnetic shields show shielding factors within a factor of 3 of conventional approaches. The vacuum demonstrator device shows that 3D-printed titanium structures are suitable for use as vacuum chambers, with the test system reaching base pressures of 5 ± 0.5 × 10−10 mbar. These demonstrations show considerable promise for the use of additive manufacturing for cold atom based quantum technologies, in future enabling improved integrated structures, allowing for the reduction in size, weight and assembly complexity.
Recent advances in the preparation, control and measurement of atomic gases have led to new insights into the quantum world and unprecedented metrological sensitivities, e.g. in measuring gravitational forces and magnetic fields. The full potential of applying such capabilities to areas as diverse as biomedical imaging, non-invasive underground mapping, and GPS-free navigation can only be realised with the scalable production of efficient, robust and portable devices. We introduce additive manufacturing as a production technique of quantum device components with unrivalled design freedom and rapid prototyping. This provides a step change in efficiency, compactness and facilitates systems integration. As a demonstrator we present an ultrahigh vacuum compatible ultracold atom source dissipating less than ten milliwatts of electrical power during field generation to produce large samples of cold rubidium gases. This disruptive technology opens the door to drastically improved integrated structures, which will further reduce size and assembly complexity in scalable series manufacture of bespoke portable quantum devices.
We demonstrate a miniaturised and highly robust system for performing Doppler-free spectroscopy on thermal atomic vapour for three frequencies as required for cold atom-based quantum technologies. The application of additive manufacturing techniques, together with efficient use of optical components, produce a compact, stable optical system, with a volume of 0.089 L and a weight of 120 g. The device occupies less than a tenth of the volume of, and is considerably lower cost than, conventional spectroscopic systems, but also offers excellent stability against environmental disturbances. We characterise the response of the system to changes in environmental temperature between 7 and 35 ∘ C and exposure to vibrations between 0 - 2000 Hz, finding that the system can reliably perform spectroscopic measurements despite substantial vibrational noise and temperature changes. Our results show that 3D-printed optical systems are an excellent solution for portable quantum technologies.
A key element in the study of cold atoms, and their use in emerging quantum technologies, is trapping the atoms in an ultra-high vacuum (UHV) chamber. Many methods have been used to trap atoms including atom chips and magneto-optical traps (MOTs). However, the bulky apparatus, and current-carrying coils, used so far in most MOTs restrict the reduction of power and physical size, as required for quantum technology applications. The advent of 3D printing technology now offers a new route to making MOTs with current paths that can be freely shaped and shrunk to several centimetres, thereby helping to reduce the power consumption and simplify the production of the MOT itself. In this paper, we present designs for 3D printed MOTs and analyse their performance by using COMSOL simulations. We predict that the 3D-printed conductors can create magnetic fields with gradients around 15 G/cm and passing through zero, as required for atom trapping, with Joule heating as low as 0.2 W.
Novel quantum technologies and devices place unprecedented demands on the performance of experimental components, while their widespread deployment beyond the laboratory necessitates increased robustness and fast affordable production.We show how the use of additive manufacturing, together with mathematical optimization techniques and innovative designs, allows the production of compact lightweight components with greatly enhanced performance.We use such components to produce a magneto-optical trap that captures approximately 2 × 10 8 rubidium atoms, employing for this purpose a compact and highly stable device for spectroscopy and optical power distribution, optimized neodymium magnet arrays for magnetic field generation, and a lightweight additively manufactured ultrahigh-vacuum chamber.We show how the use of additive manufacturing enables substantial weight reduction and stability enhancement, while also illustrating the transferability of our approach to experiments and devices across the quantum technology sector and beyond.