Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2506.05306

Full characterization of measurement-induced transitions of a superconducting qubit

Connolly, Thomas, Pavel D. Kurilovich, Vladislav D. Kurilovich, C. G. L. Bøttcher, Sumeru Hazra, Wei Dai, Andy Z. Ding, Vidul R. Joshi, Heekun Nho, Spencer Diamond, Weiss, Daniel K., Valla Fatemi, Luigi Frunzio, L. I. Glazman, Michel Devoret

Published Jun 5, 2025• 30 citations
arXivHTMLPDF

Abstract

Repeated quantum non-demolition measurement is a cornerstone of quantum error correction protocols. In superconducting qubits, the speed of dispersive state readout can be enhanced by increasing the power of the readout tone. However, such an increase has been found to result in additional qubit state transitions that violate the desired quantum non-demolition character of the measurement. Recently, the readout of a transmon superconducting qubit was improved by using a tone with frequency much larger than the qubit frequency. Here, we experimentally identify the mechanisms of readout-induced transitions in this regime. In the dominant mechanism, the energy of an incoming readout photon is partially absorbed by the transmon and partially returned to the transmission line as a photon with lower frequency. Other mechanisms involve the excitation of unwanted package modes, decay via material defects, and, at higher qubit frequencies, the activation of undesired resonances in the transmon spectrum. Our work provides a comprehensive characterization of superconducting qubit state transitions caused by a strong drive.

DOI
10.48550/arxiv.2506.05306

Related papers

Experimental Characterization and Modeling of Measurement-Induced State-Transitions in a Fluxonium Superconducting Qubit

Martijn F. S. Zwanenburg, Jinlun Hu, Eugene Y. Huang +3 more

Superconducting qubits are most often measured using dispersive readout, which, ideally, implements a projective quantum non-demolition (QND) measurement. While a larger readout drive can increase the signal and, thus, reduce discrimination errors in the readout, strong microwave drives may also cause non-QND errors by driving the qubit to a state outside the computational subspace. In this work, we experimentally characterize measurement-induced state transitions (MIST) in a fluxonium qubit over its full external flux range. We further numerically calculate the MIST errors, and find that the theory accurately predicts eleven experimentally identified regions with increased MIST. In addition to transitions to higher fluxonium levels, we also find that, at certain flux points, MIST errors are dominated by transitions that include the transmission-line-like array modes of the fluxonium's superinductor. The excellent match between theory and experiment validates that the models accurately predict the occurrence of MIST in these systems, and further highlights the influence of array modes in fluxonium readout.

quant-pharXiv:2606.17866•Jun 17, 2026•2 citations

High-frequency dispersive readout of a superconducting qubit

Pavel D. Kurilovich, Thomas Connolly, C. G. L. Bøttcher +13 more

Driving a low-dissipation, non-linear system periodically can destabilize it by exciting indirect resonances, which occur whenever an integer multiple of the drive frequency matches an integer combination of the system's mode frequencies. Avoiding such resonances is a central design constraint across physics and engineering, from radio-frequency ion traps to particle accelerators. Remarkably, the measurement of quantum bits based on superconducting circuits has so far remained limited by non-linear resonances. Measurements of qubit states are customarily performed in a regime where the frequency of the microwave readout tone is comparable to that of the circuit. In that case, the drive excites resonances that eject the qubit from its computational subspace. This limits the readout power and hence the achievable measurement fidelity. We show that a readout tone with frequency much larger than that of the circuit circumvents this problem by exponentially suppressing the resonances. Using a readout tone with frequency 12 times larger than that of our transmon qubit, we achieve a quantum non-demolition measurement fidelity of $99.931\pm0.003\%$, with an error an order of magnitude smaller than the previous record. Under these conditions, the probability of leakage to non-computational states per readout is $0.018\pm0.002\%$.

arXiv:2501.09161•Jan 15, 2025•48 citations

Measurement-Induced State transitions in Inductively-Shunted Transmons

Nicholas Zobrist, John Mark Kreikebaum, Mostafa Khezri +6 more

Fast and high-fidelity qubit measurement plays a key role in quantum error correction. In superconducting qubits, measurement is typically performed using a resonant microwave drive on a readout resonator dispersively coupled to the qubit. Shorter measurement times require larger numbers of photons populating the readout resonator, which ultimately leads to undesired measurementinduced state transitions (MIST) of the qubit. MIST can be particularly problematic because these transitions often leave the qubit in a high energy state, and the MIST locations in readout parameter space drift as a function of qubit offset charge. In transmon qubits, these drifts have been avoided using very large qubit-resonator detunings or dedicated offset charge biases. In this work, we take an alternative approach and add an inductive shunt to the transmon to eliminate the offset charge dependence and stabilize the MIST. We experimentally characterize MIST in several different inductively-shunted transmons, in agreement with quantum and semiclassical models for MIST. These results extend to other inductively-shunted qubits.

quant-pharXiv:2603.12114•Mar 13, 2026•6 citations

Offset Charge Dependence of Measurement-Induced Transitions in Transmons

Mathieu Féchant, Marie Frédérique Dumas, Denis Bénâtre +9 more

A key challenge in achieving scalable fault tolerance in superconducting quantum processors is readout fidelity, which lags behind one- and two-qubit gate fidelity. A major limitation in improving qubit readout is measurement-induced transitions, also referred to as qubit ionization, caused by multiphoton qubit-resonator excitation occurring at specific photon numbers. Since ionization can involve highly excited states, it has been predicted that in transmons-the most widely used superconducting qubit-the photon number at which measurement-induced transitions occur is gate-charge dependent. This dependence is expected to persist deep in the transmon regime where the qubit frequency is gate-charge insensitive. We experimentally confirm this prediction by characterizing measurement-induced transitions with increasing resonator photon population while actively calibrating the transmon's gate charge. Furthermore, because highly excited states are involved, achieving quantitative agreement between theory and experiment requires accounting for higher-order harmonics in the transmon Hamiltonian.

arXiv:2505.00674•Physical Review Letters•Oct 7, 2025•18 citations

Measurement-induced state transitions in multi-qubit transmon processors

Baptiste Hoyau, Alexander McDonald, Boris M. Varbanov +2 more

Dispersive readout of the transmon qubit in circuit QED is known to lose its quantum non-demolition character at small to moderate measurement drive amplitudes. This phenomenon is understood to originate from Laundau-Zener transitions at accidental multi-photon resonances, where $n$ drive photons can promote the transmon by $m$ levels. This interpretation has been shown to be in agreement with experiments characterizing the dispersive readout of a single transmon. The impact of these measurement-induced state transition (MIST) of a transmon embedded in a multi-qubit chip, however, remains largely unexplored. Here, we show that the presence of other components, such as qubits and couplers, can affect the MIST threshold of a measured transmon. To arrive at these results, we present a general method to characterize measurement-induced transition when the qubit under readout is coupled to other circuit elements, a ubiquitous situation in circuit QED-based quantum processors. As an example, we consider the case of two transmon qubits, and we show that the spectator qubit can be impacted by the measurement-induced transition of the readout qubit and, conversely, that the presence of the spectator qubit can lower the MIST threshold of the readout qubit. Finally, we explore how adding a coupler mode between the two qubits further modifies these effects.

quant-pharXiv:2606.05010•Jun 4, 2026•1 citation

Bang-bang protocol for nondispersive qubit readout

Nina del Ser, Yinan Chen, Jacob Steiner +1 more

Fast, precise, and quantum-non-demolition (QND) readout of superconducting qubits is a fundamental component of high-fidelity quantum sensing and computation. Conventional approaches typically operate in the dispersive regime, where the qubit-resonator coupling $g$ is weak compared to the detuning $Δ$. While exhibiting good QND properties, the readout rate is limited to $\sim g^2\sqrt{N}/Δ\ll g$, where $N$ is the number of photons in the resonator. QND readout in the nondispersive regime, where the readout rate reaches its full potential $\sim g$, relies on parameter sweeps that may encounter resonances, leading to measurement-induced state transitions (MIST). In this work, we study a nondispersive readout protocol that replaces these sweeps by sudden quenches of the coupling constant, using a resonator that is preloaded with photons. We call this protocol bang-bang readout, and show that it realizes single-shot projective measurements. The fidelity and QNDness of the qubit post-measurement are remarkably high, with an error that decreases like $1/N$. We show that the protocol can also be implemented without preloading the resonator by instead strongly driving the qubit, e.g., with a classical flux drive.

quant-pharXiv:2608.23681•Aug 26, 2026•0 citations
Repeated quantum non-demolition measurement is a cornerstone of quantum error correction protocols. In superconducting qubits, the speed of dispersive state readout can be enhanced by increasing the power of the readout tone. However, such an increase has been found to result in additional qubit state transitions that violate the desired quantum non-demolition character of the measurement. Recently, the readout of a transmon superconducting qubit was improved by using a tone with frequency much larger than the qubit frequency. Here, we experimentally identify the mechanisms of readout-induced transitions in this regime. In the dominant mechanism, the energy of an incoming readout photon is partially absorbed by the transmon and partially returned to the transmission line as a photon with lower frequency. Other mechanisms involve the excitation of unwanted package modes, decay via material defects, and, at higher qubit frequencies, the activation of undesired resonances in the transmon spectrum. Our work provides a comprehensive characterization of superconducting qubit state transitions caused by a strong drive.
Superconducting qubits are most often measured using dispersive readout, which, ideally, implements a projective quantum non-demolition (QND) measurement. While a larger readout drive can increase the signal and, thus, reduce discrimination errors in the readout, strong microwave drives may also cause non-QND errors by driving the qubit to a state outside the computational subspace. In this work, we experimentally characterize measurement-induced state transitions (MIST) in a fluxonium qubit over its full external flux range. We further numerically calculate the MIST errors, and find that the theory accurately predicts eleven experimentally identified regions with increased MIST. In addition to transitions to higher fluxonium levels, we also find that, at certain flux points, MIST errors are dominated by transitions that include the transmission-line-like array modes of the fluxonium's superinductor. The excellent match between theory and experiment validates that the models accurately predict the occurrence of MIST in these systems, and further highlights the influence of array modes in fluxonium readout.
Driving a low-dissipation, non-linear system periodically can destabilize it by exciting indirect resonances, which occur whenever an integer multiple of the drive frequency matches an integer combination of the system's mode frequencies. Avoiding such resonances is a central design constraint across physics and engineering, from radio-frequency ion traps to particle accelerators. Remarkably, the measurement of quantum bits based on superconducting circuits has so far remained limited by non-linear resonances. Measurements of qubit states are customarily performed in a regime where the frequency of the microwave readout tone is comparable to that of the circuit. In that case, the drive excites resonances that eject the qubit from its computational subspace. This limits the readout power and hence the achievable measurement fidelity. We show that a readout tone with frequency much larger than that of the circuit circumvents this problem by exponentially suppressing the resonances. Using a readout tone with frequency 12 times larger than that of our transmon qubit, we achieve a quantum non-demolition measurement fidelity of 99.931±0.003%99.931\pm0.003\%99.931±0.003%, with an error an order of magnitude smaller than the previous record. Under these conditions, the probability of leakage to non-computational states per readout is 0.018±0.002%0.018\pm0.002\%0.018±0.002%.
Fast and high-fidelity qubit measurement plays a key role in quantum error correction. In superconducting qubits, measurement is typically performed using a resonant microwave drive on a readout resonator dispersively coupled to the qubit. Shorter measurement times require larger numbers of photons populating the readout resonator, which ultimately leads to undesired measurementinduced state transitions (MIST) of the qubit. MIST can be particularly problematic because these transitions often leave the qubit in a high energy state, and the MIST locations in readout parameter space drift as a function of qubit offset charge. In transmon qubits, these drifts have been avoided using very large qubit-resonator detunings or dedicated offset charge biases. In this work, we take an alternative approach and add an inductive shunt to the transmon to eliminate the offset charge dependence and stabilize the MIST. We experimentally characterize MIST in several different inductively-shunted transmons, in agreement with quantum and semiclassical models for MIST. These results extend to other inductively-shunted qubits.
A key challenge in achieving scalable fault tolerance in superconducting quantum processors is readout fidelity, which lags behind one- and two-qubit gate fidelity. A major limitation in improving qubit readout is measurement-induced transitions, also referred to as qubit ionization, caused by multiphoton qubit-resonator excitation occurring at specific photon numbers. Since ionization can involve highly excited states, it has been predicted that in transmons-the most widely used superconducting qubit-the photon number at which measurement-induced transitions occur is gate-charge dependent. This dependence is expected to persist deep in the transmon regime where the qubit frequency is gate-charge insensitive. We experimentally confirm this prediction by characterizing measurement-induced transitions with increasing resonator photon population while actively calibrating the transmon's gate charge. Furthermore, because highly excited states are involved, achieving quantitative agreement between theory and experiment requires accounting for higher-order harmonics in the transmon Hamiltonian.
Dispersive readout of the transmon qubit in circuit QED is known to lose its quantum non-demolition character at small to moderate measurement drive amplitudes. This phenomenon is understood to originate from Laundau-Zener transitions at accidental multi-photon resonances, where nnn drive photons can promote the transmon by mmm levels. This interpretation has been shown to be in agreement with experiments characterizing the dispersive readout of a single transmon. The impact of these measurement-induced state transition (MIST) of a transmon embedded in a multi-qubit chip, however, remains largely unexplored. Here, we show that the presence of other components, such as qubits and couplers, can affect the MIST threshold of a measured transmon. To arrive at these results, we present a general method to characterize measurement-induced transition when the qubit under readout is coupled to other circuit elements, a ubiquitous situation in circuit QED-based quantum processors. As an example, we consider the case of two transmon qubits, and we show that the spectator qubit can be impacted by the measurement-induced transition of the readout qubit and, conversely, that the presence of the spectator qubit can lower the MIST threshold of the readout qubit. Finally, we explore how adding a coupler mode between the two qubits further modifies these effects.
Fast, precise, and quantum-non-demolition (QND) readout of superconducting qubits is a fundamental component of high-fidelity quantum sensing and computation. Conventional approaches typically operate in the dispersive regime, where the qubit-resonator coupling ggg is weak compared to the detuning ΔΔΔ. While exhibiting good QND properties, the readout rate is limited to ∼g2N/Δ≪g\sim g^2\sqrt{N}/Δ\ll g∼g2N​/Δ≪g, where NNN is the number of photons in the resonator. QND readout in the nondispersive regime, where the readout rate reaches its full potential ∼g\sim g∼g, relies on parameter sweeps that may encounter resonances, leading to measurement-induced state transitions (MIST). In this work, we study a nondispersive readout protocol that replaces these sweeps by sudden quenches of the coupling constant, using a resonator that is preloaded with photons. We call this protocol bang-bang readout, and show that it realizes single-shot projective measurements. The fidelity and QNDness of the qubit post-measurement are remarkably high, with an error that decreases like 1/N1/N1/N. We show that the protocol can also be implemented without preloading the resonator by instead strongly driving the qubit, e.g., with a classical flux drive.