Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2504.09531 · Applied Physics Letters

DC and power-frequency electric field measurement with Rydberg-atom interferometry

Yingying Han, Chun He, Zhenxiong Weng, Peng Xu, Yanting Zhao, Tao Wang

Published Jul 14, 2025• 4 citations
arXivHTMLPDF

Abstract

We propose a Rydberg-atom interferometry-based technique for direct current (DC) electric field measurement, enabling the detection of weak fields (<0.5V/cm) and unambiguous discrimination of DC electric field direction (for the one-dimensional case, i.e., ±ɛdc). This makes up for the shortcomings of measurements based on the Stark effect, which suffer from quadratic field dependence (limiting sensitivity in weak field regimes), rendering it incapable of distinguishing the DC electric field direction. Furthermore, this method extends naturally to power-frequency (PF) electric field measurement by exploiting the quasi-static approximation—valid given the PF field's characteristic timescale (∼10−2 s) vastly exceeds the interferometric measurement duration (10−6−10−3 s). Crucially, our protocol provides instantaneous PF electric field reconstruction, providing comprehensive information, including amplitude, frequency, and phase. These advancements have direct implications for traceable DC electric field measurement and noninvasive characterization of PF electric fields near high-voltage infrastructure.

DOI
10.1063/5.0272159

Related papers

Super low-frequency electric field measurement based on Rydberg atoms

Ling Li, Yuechun Jiao, Jinlian Hu +4 more

We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.

Optics Express•Aug 9, 2023•49 citations

Sensing of Low-Frequency Electric Fields Using Rydberg EIT within the Fisher Information Framework

Tianyu Zhou, Haipeng Xie, Xin Wang

Rydberg atoms, which possess exceptionally large electric dipole moments, offer a promising route for electric field sensing as well as metrology traceable to the International System of Units (SI); however, current research predominantly focuses on the microwave (MW) regime, leaving the quasi-direct current (quasi-DC) and low-frequency bands, ubiquitous in power systems, largely unexplored. In this paper, we present a theoretical investigation into low-frequency electric field detection. To this end, we establish a comprehensive modeling framework incorporating Fisher information (FI) and the Cramér-Rao lower bound (CRLB) to quantify the fundamental precision limits of electromagnetically induced transparency (EIT) readouts. Building upon this framework, we propose a linearized sensing strategy utilizing a DC-biased two-point differential measurement. Numerical validations demonstrate that this approach effectively mitigates the weak-field insensitivity for both DC and AC fields, achieving a CRLB-limited sensitivity bound of approximately $1\times 10^{-4}$ V/m/$\sqrt{\text{Hz}}$. Furthermore, to surpass the single-pass sensitivity limit, we introduce a Fabry-Pérot (FP) cavity-enhanced configuration. This architecture leverages intracavity phase modulation to significantly steepen the transmission slope, boosting the FI by over two orders of magnitude compared to standard free-space configurations. This work provides a rigorous theoretical basis and design guidance for the high-precision quantum monitoring of electromagnetic environments in smart grids.

quant-pharXiv:2604.15912•Apr 20, 2026•0 citations

Spectral characteristics of Floquet-electromagnetically induced transparency dressed by radio frequency field in a direct current electric field

Haonan DUAN, Zhonghua JI, Weixin Liu +3 more

A Rydberg atom is a special type of atom characterized by a high principal quantum number. Electric field sensors based on Rydberg atoms have received widespread attention due to their high polarizability. However, there is currently little research on the use of Rydberg atoms for direct current (DC) or low-frequency electric fields, mainly due to the shielding effect of atomic vapor cells in low-frequency electric fields, which makes accurate measurement of the electric fields extremely challenging. In this paper, we construct a Rydberg ladder configuration by using probe laser at 852 nm and coupling laser at 510 nm in a room-temperature cesium vapor cell with integrated electrode plates, thereby enabling the realizing of a Floquet-EIT (electromagnetically induced transparency) spectrum dressed by a radio frequency (RF) field in the presence of a DC electric field. We further study the influence of DC electric field on spectral characteristic. Experimentally, it is observed that when only the RF electric field is applied, the EIT spectrum displays solely even-order sidebands. Furthermore, when both the RF field and the DC electric field are simultaneously present, the first-order sideband signal of the Floquet-EIT is observed. As the intensity of the DC electric field increases, the amplitude of the first-order sideband gradually increases. However, increasing the DC electric field to a sufficient magnitude induces sideband interference, which leads the sideband amplitudes to decrease. Furthermore, increasing the RF frequency can alleviate the interference effects induced by the DC electric field on the first-order sideband. Finally, comparing the relative standard deviation of the sideband amplitudes of the Floquet-EIT spectra with the frequency shifts of the DC-Stark spectra under weak DC electric fields, we find that the measurement accuracy of the former is significantly superior to that of the latter. This work makes use of a Cs atomic vapor cell with an integrated electrode to avoid shielding effects. By observing Floquet-EIT spectra, the response of the spectra to DC electric fields is investigated. This experiment provides novel insights into the quantum sensing measurements of DC and low-frequency electric fields.

Acta Physica Sinica•Jan 1, 2025•0 citations

Continuous broadband microwave electric field measurement in Rydberg atoms based on the DC Stark effect

Kang Ouyang, Yuansheng Shi, Mingwei Lei +1 more

We demonstrate a method for broadband tunable continuous frequency electric field measurement based on the DC Stark effect in Rydberg atoms. In our experiment, we place a pair of parallel electrode plates inside the atomic vapor cell, utilizing the DC Stark effect to induce splitting and shifting of the Rydberg energy levels, thereby altering the resonance frequency of the Stark subpeaks. By employing the 52D5/2 Rydberg state, we achieve electric field measurements in the frequency range of 5.083–14.470 GHz. At an EDC of 3.45 V/cm and a resonant microwave frequency of 14.470 GHz, using heterodyne technology, the microwave electric field sensitivity is 538.89 μV/cm/√Hz, with a linear dynamic range of 23 dB. In comparison, a Rydberg heterodyne receiver with an EDC of 0 V/cm and a resonant microwave frequency of 5.083 GHz has a sensitivity of 5.43 μV/cm/√Hz and a linear dynamic range of 51 dB. This work will promote the study of atomic microwave receivers in continuous microwave frequency measurement.

Applied Physics Letters•Dec 25, 2023•27 citations

Strong Electric Field Measurement Method Based on Rydberg Atom Stark Effect

Sheng Yan, Dongping Xiao, Huaiqing Zhang +1 more

Quantum electric field measurement based on the Stark effect of Rydberg atoms has the advantages of high precision, traceability, and self-calibration. However, the current perturbation-based modeling method for the relationship between field strength and energy level shift only applies to weak fields. In applications such as power systems, electric fields can reach the kV/m level. Under such electric fields, the Rydberg state cannot ignore the strong coupling effect between adjacent highlstates, and the relationship model established by perturbation approximation is no longer accurate. This paper introduces the Landau–Zener (L-Z) tunneling model to address this limitation and describes the coupling between energy levels. It is used to construct the Rydberg atomic Hamiltonian, which includes highlstate coupling. We calculate the eigenenergies of Rydberg atoms at various electric-field strengths via matrix diagonalization, thereby obtaining a discrete mapping between field strength and energy-level shift in the strong-field regime. Subsequently, the hybrid Levenberg–Marquardt (LM) and Bayesian polynomial regression (BPR) neural network (LM-BPR) was constructed to train the discrete mapping into a continuous prediction model. In addition, the dynamic programming (DP) algorithm performs global ridge tracking on the electromagnetically induced transparency (EIT) spectrum and extracts frequency shift information from the complex EIT spectrum. Combining the above methods, strong electric field inversion based on Rydberg atoms was achieved. Experiments using the 28D5/2 Rydberg state demonstrate electric-field measurements up to 7 kV/m, with a relative error of 2.9%.

IEEE Sensors Journal•May 27, 2026•0 citations

Rydberg Atom-Based Sensors: Principles, Recent Advances, and Applications

Dinelka Somaweera, Amer Abdulghani, Ambali Alade Odebowale +7 more

Rydberg atoms are neutral atoms excited to high principal quantum number states, which endows them with exaggerated properties such as large electric dipole moments, long lifetimes, and extreme sensitivity to external electromagnetic fields. These characteristics form the foundation of Rydberg atom-based sensors, an emerging class of quantum devices capable of optically detecting electric fields across frequencies from DC to the terahertz regime. Rydberg-based electrometry operates through both Autler–Townes (AT) splitting of resonant Rydberg transitions and Stark-shift measurements for high-frequency or far-detuned fields, enabling broadband field sensing from DC to the THz regime. Using ladder-type electromagnetically induced transparency (EIT) and AT splitting, these sensors enable non-invasive, SI-traceable measurements of field amplitude, frequency, phase, and polarization. Recent developments have demonstrated broadband electric field probes, voltage calibration standards, and compact RF receivers based on thermal vapor cells and integrated photonic architectures. Furthermore, innovations in multi-photon EIT, superheterodyne readout, and multi wave mixing have expanded the dynamic range and bandwidth of Rydberg-based electrometry. Despite challenges related to environmental perturbations, linewidth broadening, and laser stabilization, ongoing advances in atomic control, hybrid photonic integration, and EIT-based readout promise scalable, chip-compatible sensors. This review summarizes the physical principles, experimental progress, and emerging applications of Rydberg atom-based sensing, emphasizing their potential for next generation quantum metrology, wireless communication, and precision field mapping.

Photonics•Dec 12, 2025•14 citations
We propose a Rydberg-atom interferometry-based technique for direct current (DC) electric field measurement, enabling the detection of weak fields (<0.5V/cm) and unambiguous discrimination of DC electric field direction (for the one-dimensional case, i.e., ±ɛdc). This makes up for the shortcomings of measurements based on the Stark effect, which suffer from quadratic field dependence (limiting sensitivity in weak field regimes), rendering it incapable of distinguishing the DC electric field direction. Furthermore, this method extends naturally to power-frequency (PF) electric field measurement by exploiting the quasi-static approximation—valid given the PF field's characteristic timescale (∼10−2 s) vastly exceeds the interferometric measurement duration (10−6−10−3 s). Crucially, our protocol provides instantaneous PF electric field reconstruction, providing comprehensive information, including amplitude, frequency, and phase. These advancements have direct implications for traceable DC electric field measurement and noninvasive characterization of PF electric fields near high-voltage infrastructure.
We demonstrate the measurement of super low-frequency electric field using Rydberg atoms in an atomic vapor cell with inside parallel electrodes, thus overcoming the low-frequency electric-field-screening effect at frequencies below a few kHz. Rydberg electromagnetically induced transparency (EIT) spectra involving 52 D 5/2 state is employed to measure the signal electric field. An auxiliary DC field is applied to improve the sensitivity. A DC Stark map is demonstrated, where the utilized 52 D 5/2 exhibits m j = 1/2, 3/2, 5/2 Stark shifts and splittings. The m j = 1/2 state is employed to detect the signal field because of its larger polarizability than that of m j = 3/2, 5/2. Also, we show that the strength of the spectrum is dependent on the angle between the laser polarizations and the electric field. With optimization of the applied DC field to shift the m j = 1/2 Rydberg energy level to a high sensitivity region and the laser polarizations to obtain the maximum m j = 1/2 signal, we achieve the detection of the signal electric field with a frequency of 100 Hz down to 214.8 µ V/cm with a sensitivity of 67.9 µ V cm −1 Hz −1/2 , and the linear dynamic range is over 37 dB. Our work extends the measurement frequency of Rydberg sensors to super low frequency with high sensitivity, which has the advantages of high sensitivity and miniaturization for receiving super low frequency.
Rydberg atoms, which possess exceptionally large electric dipole moments, offer a promising route for electric field sensing as well as metrology traceable to the International System of Units (SI); however, current research predominantly focuses on the microwave (MW) regime, leaving the quasi-direct current (quasi-DC) and low-frequency bands, ubiquitous in power systems, largely unexplored. In this paper, we present a theoretical investigation into low-frequency electric field detection. To this end, we establish a comprehensive modeling framework incorporating Fisher information (FI) and the Cramér-Rao lower bound (CRLB) to quantify the fundamental precision limits of electromagnetically induced transparency (EIT) readouts. Building upon this framework, we propose a linearized sensing strategy utilizing a DC-biased two-point differential measurement. Numerical validations demonstrate that this approach effectively mitigates the weak-field insensitivity for both DC and AC fields, achieving a CRLB-limited sensitivity bound of approximately 1×10−41\times 10^{-4}1×10−4 V/m/Hz\sqrt{\text{Hz}}Hz​. Furthermore, to surpass the single-pass sensitivity limit, we introduce a Fabry-Pérot (FP) cavity-enhanced configuration. This architecture leverages intracavity phase modulation to significantly steepen the transmission slope, boosting the FI by over two orders of magnitude compared to standard free-space configurations. This work provides a rigorous theoretical basis and design guidance for the high-precision quantum monitoring of electromagnetic environments in smart grids.
A Rydberg atom is a special type of atom characterized by a high principal quantum number. Electric field sensors based on Rydberg atoms have received widespread attention due to their high polarizability. However, there is currently little research on the use of Rydberg atoms for direct current (DC) or low-frequency electric fields, mainly due to the shielding effect of atomic vapor cells in low-frequency electric fields, which makes accurate measurement of the electric fields extremely challenging. In this paper, we construct a Rydberg ladder configuration by using probe laser at 852 nm and coupling laser at 510 nm in a room-temperature cesium vapor cell with integrated electrode plates, thereby enabling the realizing of a Floquet-EIT (electromagnetically induced transparency) spectrum dressed by a radio frequency (RF) field in the presence of a DC electric field. We further study the influence of DC electric field on spectral characteristic. Experimentally, it is observed that when only the RF electric field is applied, the EIT spectrum displays solely even-order sidebands. Furthermore, when both the RF field and the DC electric field are simultaneously present, the first-order sideband signal of the Floquet-EIT is observed. As the intensity of the DC electric field increases, the amplitude of the first-order sideband gradually increases. However, increasing the DC electric field to a sufficient magnitude induces sideband interference, which leads the sideband amplitudes to decrease. Furthermore, increasing the RF frequency can alleviate the interference effects induced by the DC electric field on the first-order sideband. Finally, comparing the relative standard deviation of the sideband amplitudes of the Floquet-EIT spectra with the frequency shifts of the DC-Stark spectra under weak DC electric fields, we find that the measurement accuracy of the former is significantly superior to that of the latter. This work makes use of a Cs atomic vapor cell with an integrated electrode to avoid shielding effects. By observing Floquet-EIT spectra, the response of the spectra to DC electric fields is investigated. This experiment provides novel insights into the quantum sensing measurements of DC and low-frequency electric fields.
We demonstrate a method for broadband tunable continuous frequency electric field measurement based on the DC Stark effect in Rydberg atoms. In our experiment, we place a pair of parallel electrode plates inside the atomic vapor cell, utilizing the DC Stark effect to induce splitting and shifting of the Rydberg energy levels, thereby altering the resonance frequency of the Stark subpeaks. By employing the 52D5/2 Rydberg state, we achieve electric field measurements in the frequency range of 5.083–14.470 GHz. At an EDC of 3.45 V/cm and a resonant microwave frequency of 14.470 GHz, using heterodyne technology, the microwave electric field sensitivity is 538.89 μV/cm/√Hz, with a linear dynamic range of 23 dB. In comparison, a Rydberg heterodyne receiver with an EDC of 0 V/cm and a resonant microwave frequency of 5.083 GHz has a sensitivity of 5.43 μV/cm/√Hz and a linear dynamic range of 51 dB. This work will promote the study of atomic microwave receivers in continuous microwave frequency measurement.
Quantum electric field measurement based on the Stark effect of Rydberg atoms has the advantages of high precision, traceability, and self-calibration. However, the current perturbation-based modeling method for the relationship between field strength and energy level shift only applies to weak fields. In applications such as power systems, electric fields can reach the kV/m level. Under such electric fields, the Rydberg state cannot ignore the strong coupling effect between adjacent highlstates, and the relationship model established by perturbation approximation is no longer accurate. This paper introduces the Landau–Zener (L-Z) tunneling model to address this limitation and describes the coupling between energy levels. It is used to construct the Rydberg atomic Hamiltonian, which includes highlstate coupling. We calculate the eigenenergies of Rydberg atoms at various electric-field strengths via matrix diagonalization, thereby obtaining a discrete mapping between field strength and energy-level shift in the strong-field regime. Subsequently, the hybrid Levenberg–Marquardt (LM) and Bayesian polynomial regression (BPR) neural network (LM-BPR) was constructed to train the discrete mapping into a continuous prediction model. In addition, the dynamic programming (DP) algorithm performs global ridge tracking on the electromagnetically induced transparency (EIT) spectrum and extracts frequency shift information from the complex EIT spectrum. Combining the above methods, strong electric field inversion based on Rydberg atoms was achieved. Experiments using the 28D5/2 Rydberg state demonstrate electric-field measurements up to 7 kV/m, with a relative error of 2.9%.
Rydberg atoms are neutral atoms excited to high principal quantum number states, which endows them with exaggerated properties such as large electric dipole moments, long lifetimes, and extreme sensitivity to external electromagnetic fields. These characteristics form the foundation of Rydberg atom-based sensors, an emerging class of quantum devices capable of optically detecting electric fields across frequencies from DC to the terahertz regime. Rydberg-based electrometry operates through both Autler–Townes (AT) splitting of resonant Rydberg transitions and Stark-shift measurements for high-frequency or far-detuned fields, enabling broadband field sensing from DC to the THz regime. Using ladder-type electromagnetically induced transparency (EIT) and AT splitting, these sensors enable non-invasive, SI-traceable measurements of field amplitude, frequency, phase, and polarization. Recent developments have demonstrated broadband electric field probes, voltage calibration standards, and compact RF receivers based on thermal vapor cells and integrated photonic architectures. Furthermore, innovations in multi-photon EIT, superheterodyne readout, and multi wave mixing have expanded the dynamic range and bandwidth of Rydberg-based electrometry. Despite challenges related to environmental perturbations, linewidth broadening, and laser stabilization, ongoing advances in atomic control, hybrid photonic integration, and EIT-based readout promise scalable, chip-compatible sensors. This review summarizes the physical principles, experimental progress, and emerging applications of Rydberg atom-based sensing, emphasizing their potential for next generation quantum metrology, wireless communication, and precision field mapping.