Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2503.20022 · Review of Scientific Instruments

Picosecond Josephson samplers: Modeling and measurements

Logan A. Howe, Bart J. Van Zeghbroeck, David I. Olaya, John P. Biesecker, Charles J. Burroughs, Samuel P. Benz, P. F. Hopkins

Published Jun 1, 2025• 0 citations
arXivHTMLPDF

Abstract

Measurement of signals generated by superconducting Josephson junction (JJ) circuits require ultra-fast components located in close proximity to the generating circuitry. We report a detailed study of optimal design criteria for a JJ-based sampler that balances the highest sampler bandwidth (shortest 10%-90% rise time) with minimal sampled waveform distortion. We explore the impacts on the performance of a sampler, realized using a single underdamped JJ as the logical sampling element (the comparator), due to the type of signal-comparator coupling scheme that is utilized (galvanic, inductive, or capacitive). In these simulations, we emulate the entire waveform reconstruction sampling process, via comparator threshold detection, while sweeping the time location at which the waveform is being sampled. We extract the sampled waveform rise time [or full width at half maximum (FWHM)] as a function of the comparator's Stewart-McCumber parameter and as a function of the coupling strength between the device under test and comparator. Based on our simulation results, we design, fabricate, and characterize a cryocooled (3.6 K operating temperature) JJ sampler utilizing the NIST state-of-the-art Nb/amorphous-Si/Nb junctions. We separately sample a step signal and an impulse generator co-located on-chip with the comparator and sampling strobe generator by implementing the same binary search comparator threshold detection technique during sampler operation as is used in simulation. With this technique, the system is fully digital and automated, and the operation of the fabricated device directly mirrors simulation. Our sampler technology shows a 10%-90% rise time of 3.3 ps and the capability to measure transient pulse widths of 2.5 ps FWHM. A linear system analysis of sampled waveforms indicates a 3 dB bandwidth of 225 GHz, but we demonstrate effective measurement of signals well above this-as high as 600 GHz.

DOI
10.1063/5.0255228

Related papers

Technologies For A Superconducting Sampling Oscilloscope/Time Domain Reflectometer

Stephen R. Whiteley, Eric Hanson, Gert K. G. Hohenwarter +2 more

HYPRES, Inc. has introduced to the commercial marketplace a Sampling Oscilloscope/Time Domain Reflectometer (TDR) based on Josephson junction technology. The unit offers measurement performance commensurate with the inherent high speed of the Josephson elements, e.g., bandwidths in excess of 70 GHz and rise times on the order of 5 ps. A Josephson {rigger recognizer and delay circuit allows triggering of the sampling oscilloscope from the signal itself, with full view of the trigger point. Input modules offering different sensitivities or TDR capability are quickly interchangeable, and operating temperature is achieved in less than one minute. The technical details of the cooling technique and the chip circuitry will be described in this paper .

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Sep 8, 1988•10 citations

A Direct Coupled Josephson Sampler

Hiroshi Akoh, Shigeki Sakai, Akihiko Yagi +1 more

A direct coupled Josephson sampler with a single junction as a sampling gate which is directly connected with a sampler pulser and unknown signal sources by resistors is reported. Devices are fabricated by a Pb-alloy technology with a minimum size of 2.5×2.5 µm2 and a current density of 4 kA/cm2 for junctions. The sampler reconstructs a latching waveform with a 10 ps rise time from an interferometer within a few µA current sensitivity.

Japanese Journal of Applied Physics•Jul 1, 1983•24 citations

A direct coupled Josephson sampler concept with a vortex to vortex transition sampling pulse generator

Henrik Kratz, W. Jutzi

A Josephson sampler with direct resistive coupling between sampling gate and sampling pulse generator has been designed and simulated. The sampling gate and the sampling pulse generator comprise two Josephson junction interferometers. A short sampling pulse of 3ps width is generated at a suitable vortex to vortex transition. Delays up to 200ps between the sampling pulse and the main trigger input could be generated with an electronically adjustable circuit on the same chip. A layout of the complete sampling circuit, i.e. the sampling gate, the sampling pulse generator and the electronic delay circuit on a single 36mm2chip has been achieved for the Nb-NbxOy-PbInAu technology. The minimum line width is 8μm. Forj_{\max} = 3kA/cm2a time resolution of 3.5ps is predicted.

IEEE Transactions on Magnetics•Mar 1, 1985•5 citations

HTS Sampler with Improved Circuit Design and Layout

Michitaka Maruyama, H. Wakana, Tsunehiro Hato +6 more

This paper reviews our progress on the high-T c superconducting (HTS) sampler development, covering from the circuit design to the latest experimental data in the sinusoidal and pulse waveform measurements. A computer simulation has revealed that our sampler circuit with an improved design enables waveform measurement with the bandwidth over 100 GHz even with the thermal noise at around 40 K. Using the HTS sampler circuits fabricated employing an improved layout, we demonstrated waveform measurements for sinusoidal signals with frequencies of up to 50 GHz, the upper limit of the signal generator we used, both in the voltage-input-type system with a high-frequency input line and in the current-input-type one with a superconducting pickup coil. In the pulse measurement using an on-chip sampler, we succeeded in observing pico-second-order-wide single flux quantum (SFQ) current pulses, suggesting the potential bandwidth of our HTS sampler of more than 125 GHz.

IEICE Transactions on Electronics•Mar 1, 2007•7 citations

High-T/sub c/ superconductor sampler system for digital signal waveform measurement

Mutsuo Hidaka, T. Satoh, Masato Kimishima +2 more

We are developing a system using a high-T/sub c/ superconductor (HTS) sampler for measuring a 40-Gbps digital signal waveform, which will be used in next generation ultra-high-speed communications. To measure a 40-Gbps digital signal, the sampler bandwidth needs to be more than 120 GHz. The HTS sampler has the potential to achieve this bandwidth. As a first step in developing this system, we have developed a prototype whose target bandwidth is 40 GHz. In the prototype system, the sampler chip is cooled down to 35 K by a single-stage Stirling cryocooler, and the digital signal is transmitted to the sampler chip via a 40-GHz bandwidth assembly line. This system is the first to integrate an HTS device, a cryocooler, and a high-frequency assemble line. A 5.9-Gbps digital waveform was reconstituted by the prototype system with the correct period.

IEEE Transactions on Applied Superconductivity•Mar 1, 2001•20 citations

Experimental investigation of a high frequency sampling system based on shunted Josephson junctions

V. K. Kaplunenko, M. Khabipov, E. Goldobin

The authors propose a new type of sampler design based on shunted junctions ( beta c =1). The sampler is to be used for the investigation of single flux quantum devices (RSFQ) employing similar junctions (Kaplunenko et al. 1989, Filippenko et al. 1991). They measure the time resolution of the sampler and delay time of the shunted Josephson junction array. The circuit was manufactured on a single chip and was DC powered. They employed Nb-AlO x -Nb tunnel junctions of 300 A m -2 critical current density and observed Josephson oscillations of the output junction at frequencies from 6 to 50 GHz. Despite a long plasma period of 20 ps the time resolution was 5 ps. The transmission line of 27 Josephson junctions (critical current 165 mu A each) demonstrated time delay of 0.5 ps mu A -1 .

Superconductor Science and Technology•Nov 1, 1991•15 citations
Measurement of signals generated by superconducting Josephson junction (JJ) circuits require ultra-fast components located in close proximity to the generating circuitry. We report a detailed study of optimal design criteria for a JJ-based sampler that balances the highest sampler bandwidth (shortest 10%-90% rise time) with minimal sampled waveform distortion. We explore the impacts on the performance of a sampler, realized using a single underdamped JJ as the logical sampling element (the comparator), due to the type of signal-comparator coupling scheme that is utilized (galvanic, inductive, or capacitive). In these simulations, we emulate the entire waveform reconstruction sampling process, via comparator threshold detection, while sweeping the time location at which the waveform is being sampled. We extract the sampled waveform rise time [or full width at half maximum (FWHM)] as a function of the comparator's Stewart-McCumber parameter and as a function of the coupling strength between the device under test and comparator. Based on our simulation results, we design, fabricate, and characterize a cryocooled (3.6 K operating temperature) JJ sampler utilizing the NIST state-of-the-art Nb/amorphous-Si/Nb junctions. We separately sample a step signal and an impulse generator co-located on-chip with the comparator and sampling strobe generator by implementing the same binary search comparator threshold detection technique during sampler operation as is used in simulation. With this technique, the system is fully digital and automated, and the operation of the fabricated device directly mirrors simulation. Our sampler technology shows a 10%-90% rise time of 3.3 ps and the capability to measure transient pulse widths of 2.5 ps FWHM. A linear system analysis of sampled waveforms indicates a 3 dB bandwidth of 225 GHz, but we demonstrate effective measurement of signals well above this-as high as 600 GHz.
HYPRES, Inc. has introduced to the commercial marketplace a Sampling Oscilloscope/Time Domain Reflectometer (TDR) based on Josephson junction technology. The unit offers measurement performance commensurate with the inherent high speed of the Josephson elements, e.g., bandwidths in excess of 70 GHz and rise times on the order of 5 ps. A Josephson {rigger recognizer and delay circuit allows triggering of the sampling oscilloscope from the signal itself, with full view of the trigger point. Input modules offering different sensitivities or TDR capability are quickly interchangeable, and operating temperature is achieved in less than one minute. The technical details of the cooling technique and the chip circuitry will be described in this paper .
A Josephson sampler with direct resistive coupling between sampling gate and sampling pulse generator has been designed and simulated. The sampling gate and the sampling pulse generator comprise two Josephson junction interferometers. A short sampling pulse of 3ps width is generated at a suitable vortex to vortex transition. Delays up to 200ps between the sampling pulse and the main trigger input could be generated with an electronically adjustable circuit on the same chip. A layout of the complete sampling circuit, i.e. the sampling gate, the sampling pulse generator and the electronic delay circuit on a single 36mm2chip has been achieved for the Nb-NbxOy-PbInAu technology. The minimum line width is 8μm. Forj_{\max} = 3kA/cm2a time resolution of 3.5ps is predicted.
This paper reviews our progress on the high-T c superconducting (HTS) sampler development, covering from the circuit design to the latest experimental data in the sinusoidal and pulse waveform measurements. A computer simulation has revealed that our sampler circuit with an improved design enables waveform measurement with the bandwidth over 100 GHz even with the thermal noise at around 40 K. Using the HTS sampler circuits fabricated employing an improved layout, we demonstrated waveform measurements for sinusoidal signals with frequencies of up to 50 GHz, the upper limit of the signal generator we used, both in the voltage-input-type system with a high-frequency input line and in the current-input-type one with a superconducting pickup coil. In the pulse measurement using an on-chip sampler, we succeeded in observing pico-second-order-wide single flux quantum (SFQ) current pulses, suggesting the potential bandwidth of our HTS sampler of more than 125 GHz.
We are developing a system using a high-T/sub c/ superconductor (HTS) sampler for measuring a 40-Gbps digital signal waveform, which will be used in next generation ultra-high-speed communications. To measure a 40-Gbps digital signal, the sampler bandwidth needs to be more than 120 GHz. The HTS sampler has the potential to achieve this bandwidth. As a first step in developing this system, we have developed a prototype whose target bandwidth is 40 GHz. In the prototype system, the sampler chip is cooled down to 35 K by a single-stage Stirling cryocooler, and the digital signal is transmitted to the sampler chip via a 40-GHz bandwidth assembly line. This system is the first to integrate an HTS device, a cryocooler, and a high-frequency assemble line. A 5.9-Gbps digital waveform was reconstituted by the prototype system with the correct period.
The authors propose a new type of sampler design based on shunted junctions ( beta c =1). The sampler is to be used for the investigation of single flux quantum devices (RSFQ) employing similar junctions (Kaplunenko et al. 1989, Filippenko et al. 1991). They measure the time resolution of the sampler and delay time of the shunted Josephson junction array. The circuit was manufactured on a single chip and was DC powered. They employed Nb-AlO x -Nb tunnel junctions of 300 A m -2 critical current density and observed Josephson oscillations of the output junction at frequencies from 6 to 50 GHz. Despite a long plasma period of 20 ps the time resolution was 5 ps. The transmission line of 27 Josephson junctions (critical current 165 mu A each) demonstrated time delay of 0.5 ps mu A -1 .