Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2412.16366 · APS Open Science

Nonlinearities in atomic radio receivers: Harmonic and intermodulation distortion

Luís F. Gonçalves, Teng Zhang, Georg A. Raithel, David Alexander Anderson

Published Jul 14, 2026• 3 citations
arXivHTMLPDF

Abstract

Rydberg sensors offer a unique approach to radio-frequency (rf) detection, leveraging the high sensitivity and quantum properties of highly excited atomic states to achieve performance levels beyond classical technologies. Nonlinear responses and distortion behavior in Rydberg atom receivers are critical to evaluating and establishing performance metrics and capabilities such as spur-free dynamic range and tolerance to unwanted interfering signals. We report here on the measurement and characterization of nonlinear behavior and spurious response of a Rydberg atomic heterodyne receiver. Single-tone and two-tone testing procedures are developed and implemented for measurement of harmonic and intermodulation distortion in Rydberg atomic receivers based on multiphoton Rydberg spectroscopy and radio-frequency heterodyne signal detection and demodulation in an atomic vapor. For a predetermined set of atomic receiver parameters and rf carrier wave in the super high frequency band near-resonant to a cesium Rydberg transition, we measure and characterize atomic receiver selectivity, bandwidth, roll-off, compression point (P1dB), second-order (IP2) and third-order (IP3) intercepts, and spur-free dynamic range. Receiver intermodulation distortion is characterized for the case of an interfering signal wave applied at two frequency offsets relative to the near-resonant reference local oscillator, Δ F / F = 10 − 4 at 6 dB and 10 − 6 at 22 dB single-tone bandwidths, respectively. We observe that under suitable operating conditions the atomic receiver can exhibit a suppression of harmonic and intermodulation distortion relative to that of classical receiver mixer amplifiers.

DOI
10.1103/3pht-dvg9

Related papers

A millimeter-wave atomic receiver

Remy Legaie, Georg A. Raithel, David Alexander Anderson

Rydberg quantum sensors are sensitive to radio-frequency fields across an ultra-wide frequency range spanning megahertz to terahertz electromagnetic waves resonant with Rydberg atom dipole transitions. Here, we demonstrate an atomic millimeter-wave heterodyne receiver employing continuous-wave lasers stabilized to an optical frequency comb. We characterize the atomic receiver in the W-band at a signal frequency of f = 95.992 512 GHz and demonstrate a sensitivity of 7.9 μV/m/Hz with a linear dynamic range in power greater than 70 dB. We develop frequency selectivity metrics for atomic receivers and demonstrate their use in our millimeter-wave receiver, including signal rejection levels at signal frequency offsets Δf/f = 10−4, 10−5, and 10−6; 3, 6, 9, and 12-dB bandwidths; filter roll-off; and shape factor analysis. Our work represents an important advance toward future studies and applications of atomic receiver science and technology in weak millimeter-wave and high-frequency signal detection.

arXiv:2306.17114•AVS Quantum Science•Apr 5, 2024•21 citations

High-sensitivity and low-harmonic microwave detection using Rydberg atoms based on a loop-level structure

Yu Tang, Shuang Ren, Chuang Yang +3 more

We propose and investigate a Rydberg atom sensor based on a loop-level structure, which utilizes the eigenfrequencies of the energy levels as a reference. This design eliminates the need for the local oscillator (LO) electric field required in the traditional superheterodyne structure while maintaining a linear relationship between the readout signal and the microwave (MW) electric field to be measured, along with exhibiting significantly lower harmonic distortion. For experimental validation, we implemented a cesium atomic system based on the loop five-level structure. The system achieved a sensitivity of 62 nVcm -1 Hz -1/2 and maintained 30 dB of harmonic suppression even near the nonlinear operational region under the strong electric field, which is approximately 20 dB higher than that of the superheterodyne structure. This work demonstrates that loop-level-based atomic sensors enable high-sensitivity and wide-dynamic-range (including nonlinear region) MW detection, making them particularly suitable for receiving frequency- and phase-modulated signals that are insensitive to power variations.

Optics Express•May 9, 2025•1 citation

Probing bandwidth and sensitivity in Rydberg atom sensing via optical homodyne and rf heterodyne detection

Dixith Manchaiah, Stone Oliver, Samuel Berweger +2 more

Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.

arXiv:2509.20632•Physical Review A•Dec 22, 2025•8 citations

Optimization strategies for operational parameters of Rydberg atom-based amplitude modulation receiver

Yuhao 宇豪 Wu 吴, Dongping 冬萍 Xiao 肖, Huaiqing Zhang +1 more

Abstract The Rydberg atom-based receiver, as a novel type of antenna, demonstrates broad application prospects in the field of microwave communications. However, since Rydberg atomic receivers are nonlinear systems, mismatches between the parameters of the received amplitude modulation (AM) signals and the system’s linear workspace and demodulation operating points can cause severe distortion in the demodulated signals. To address this, the article proposes a method for determining the operational parameters based on the mean square error (MSE) and total harmonic distortion (THD) assessments and presents strategies for optimizing the system’s operational parameters focusing on linear response characteristics (LRC) and linear dynamic range (LDR). Specifically, we employ a method that minimizes the MSE to define the system’s linear workspace, thereby ensuring the system has a good LRC while maximizing the LDR. To ensure that the signal always operates within the linear workspace, an appropriate carrier amplitude is set as the demodulation operating point. By calculating the THD at different operating points, the LRC performance within different regions of the linear workspace is evaluated, and corresponding optimization strategies based on the range of signal strengths are proposed. Moreover, to more accurately restore the baseband signal, we establish a mapping relationship between the carrier Rabi frequency and the transmitted power of the probe light, and optimize the slope of the linear demodulation function to reduce the MSE to less than 0.8 × 10 −4 . Finally, based on these methods for determining the operational parameters, we explore the effects of different laser Rabi frequencies on the system performance, and provide optimization recommendations. This research provides robust support for the design of high-performance Rydberg atom-based AM receivers.

Chinese Physics B•Oct 18, 2024•8 citations

Impairments Characterisation for Deployable Rydberg Atomic Quantum Receivers

Ainara Kazymova, Tierui Gong, Yong Liang Guan +1 more

Rydberg atomic quantum receivers (RAQRs) recently gained significant interest. However, their impairments characterisation, which is critical for practical deployments, remains under-examined. In this paper, we evaluate how deviations in five operational parameters (atomic density, EIT linewidth, local oscillator (LO) amplitude, laser frequency, and probe power) impact the signal-to-noise ratio (SNR), third-order intercept (IIP3), 1 dB compression $\left(P_{1 \mathrm{~dB}}\right)$, and spurious-free dynamic range (SFDR). By expanding the atomic coherence in powers of signal amplitude, we classify deviation responses into three distinct categories. All three categories remain robust under Doppler broadening from $200 \mu \mathrm{~K}$ to 300 K. Crucially, the LO amplitude falls into a regime where IIP3 degrades linearly while the SNR changes only quadratically. As this linearity loss can go easily undetected during standard sensitivity checks, LO amplitude requires tightest control (+7% tolerance). We further derive two closed-form relationships governing the RAQRs. The first one features how much the SNR can be improved as atomic density increases, yielding improvement equal to or less than 20 dB for every tenfold increase in atomic density. The second one shows that a laser frequency drift of about 55 kHz reduces the SNR by an order of 1 dB.

IEEE International Symposium on Personal, Indoor and Mobile Radio Communications (PIMRC)•Sep 1, 2026•0 citations

Wideband Quantum Transduction for Rydberg Atomic Receivers Using Six-Wave Mixing

Yuanbin Chen, Chau Yuen, Chong Meng Samson See

This paper investigates a six-wave mixing (SWM)-based Rydberg atomic receiver as a wideband radio frequency (RF)-to-optical quantum transducer. Specifically, we develop an explicit baseband input-output model that bridges the RF-induced atomic coherence to the detected optical readout. Based on the exact detected SWM response, we develop a reduced-order closed-form two-pole low-pass approximation under the near-resonant weak-signal of interest, which provides an analytical insight into how the 3-dB bandwidth is manipulated by the dressed higher-level atomic dynamics and optical/RF parameters. The validity range of this approximation is then quantified to clarify the operating conditions under which this reduced-order model accurately represents the exact SWM response. We further characterize the linear dynamic range by employing the 1-dB compression point (P1dB) and the input-referred third-order intercept point (IIP3), unveiling a communication-compatible characterization of the bandwidth-sensitivity-linearity trade-off. Extensive simulation results demonstrate that SWM can achieve a 3-dB bandwidth of approximately 10 MHz while maintaining favorable linearity and sensitivity under the strict low-pass condition. The comparison with the EIT regime indicates that the two schemes should be treated as complementary rather than universally ordered. From an engineering perspective, the preferred SWM operating region is therefore not the one with the largest bandwidth, but the one that simultaneously provides a large bandwidth, acceptable sensitivity, favorable linearity, and low-pass regularity.

quant-pharXiv:2602.13955•IEEE Journal on Selected Areas in Communications•Feb 17, 2026•5 citations
Rydberg sensors offer a unique approach to radio-frequency (rf) detection, leveraging the high sensitivity and quantum properties of highly excited atomic states to achieve performance levels beyond classical technologies. Nonlinear responses and distortion behavior in Rydberg atom receivers are critical to evaluating and establishing performance metrics and capabilities such as spur-free dynamic range and tolerance to unwanted interfering signals. We report here on the measurement and characterization of nonlinear behavior and spurious response of a Rydberg atomic heterodyne receiver. Single-tone and two-tone testing procedures are developed and implemented for measurement of harmonic and intermodulation distortion in Rydberg atomic receivers based on multiphoton Rydberg spectroscopy and radio-frequency heterodyne signal detection and demodulation in an atomic vapor. For a predetermined set of atomic receiver parameters and rf carrier wave in the super high frequency band near-resonant to a cesium Rydberg transition, we measure and characterize atomic receiver selectivity, bandwidth, roll-off, compression point (P1dB), second-order (IP2) and third-order (IP3) intercepts, and spur-free dynamic range. Receiver intermodulation distortion is characterized for the case of an interfering signal wave applied at two frequency offsets relative to the near-resonant reference local oscillator, Δ F / F = 10 − 4 at 6 dB and 10 − 6 at 22 dB single-tone bandwidths, respectively. We observe that under suitable operating conditions the atomic receiver can exhibit a suppression of harmonic and intermodulation distortion relative to that of classical receiver mixer amplifiers.
Rydberg quantum sensors are sensitive to radio-frequency fields across an ultra-wide frequency range spanning megahertz to terahertz electromagnetic waves resonant with Rydberg atom dipole transitions. Here, we demonstrate an atomic millimeter-wave heterodyne receiver employing continuous-wave lasers stabilized to an optical frequency comb. We characterize the atomic receiver in the W-band at a signal frequency of f = 95.992 512 GHz and demonstrate a sensitivity of 7.9 μV/m/Hz with a linear dynamic range in power greater than 70 dB. We develop frequency selectivity metrics for atomic receivers and demonstrate their use in our millimeter-wave receiver, including signal rejection levels at signal frequency offsets Δf/f = 10−4, 10−5, and 10−6; 3, 6, 9, and 12-dB bandwidths; filter roll-off; and shape factor analysis. Our work represents an important advance toward future studies and applications of atomic receiver science and technology in weak millimeter-wave and high-frequency signal detection.
We propose and investigate a Rydberg atom sensor based on a loop-level structure, which utilizes the eigenfrequencies of the energy levels as a reference. This design eliminates the need for the local oscillator (LO) electric field required in the traditional superheterodyne structure while maintaining a linear relationship between the readout signal and the microwave (MW) electric field to be measured, along with exhibiting significantly lower harmonic distortion. For experimental validation, we implemented a cesium atomic system based on the loop five-level structure. The system achieved a sensitivity of 62 nVcm -1 Hz -1/2 and maintained 30 dB of harmonic suppression even near the nonlinear operational region under the strong electric field, which is approximately 20 dB higher than that of the superheterodyne structure. This work demonstrates that loop-level-based atomic sensors enable high-sensitivity and wide-dynamic-range (including nonlinear region) MW detection, making them particularly suitable for receiving frequency- and phase-modulated signals that are insensitive to power variations.
Rydberg atom based sensors allow for SI traceable measurements and show promise for applications in the field of communication and radar technologies. In this article, we investigate the bandwidth and sensitivity of a Rydberg atom-based sensor in a rubidium vapor cell using Rydberg electromagnetically induced transparency (EIT) spectroscopy. We employ a radio-frequency (RF) heterodyne measurement technique in combination with an optical homodyne setup to extend the achievable range between sensitivity and bandwidth in a Rydberg sensor. While the bandwidth of Rydberg sensors are limited by the transit time of atoms and the Rabi frequency of the coupling field, achieving higher bandwidth through smaller beam sizes is thought to compromise sensitivity due to reduced EIT signal strength. Using optical homodyne detection, we demonstrate that sensitivity is preserved while achieving a response bandwidth of 8 MHz. In addition, using the Rydberg sensor, we receive digital communication signals and present error vector magnitude (EVM) measurements as a function of varying symbol rates and bandwidth of the Rydberg sensor. Furthermore, the sensor's performance is compared with a conventional RF mixer. We establish that the bandwidth of a Rydberg sensor when receiving a pure tone is not the same as the bandwidth of the sensor when receiving a modulated signal. This difference results from the spreading of symbols in the frequency domain, leading to a reduction of the signal to noise ratio (SNR) and an accumulation of noise over the total span of the modulated signal.
Abstract The Rydberg atom-based receiver, as a novel type of antenna, demonstrates broad application prospects in the field of microwave communications. However, since Rydberg atomic receivers are nonlinear systems, mismatches between the parameters of the received amplitude modulation (AM) signals and the system’s linear workspace and demodulation operating points can cause severe distortion in the demodulated signals. To address this, the article proposes a method for determining the operational parameters based on the mean square error (MSE) and total harmonic distortion (THD) assessments and presents strategies for optimizing the system’s operational parameters focusing on linear response characteristics (LRC) and linear dynamic range (LDR). Specifically, we employ a method that minimizes the MSE to define the system’s linear workspace, thereby ensuring the system has a good LRC while maximizing the LDR. To ensure that the signal always operates within the linear workspace, an appropriate carrier amplitude is set as the demodulation operating point. By calculating the THD at different operating points, the LRC performance within different regions of the linear workspace is evaluated, and corresponding optimization strategies based on the range of signal strengths are proposed. Moreover, to more accurately restore the baseband signal, we establish a mapping relationship between the carrier Rabi frequency and the transmitted power of the probe light, and optimize the slope of the linear demodulation function to reduce the MSE to less than 0.8 × 10 −4 . Finally, based on these methods for determining the operational parameters, we explore the effects of different laser Rabi frequencies on the system performance, and provide optimization recommendations. This research provides robust support for the design of high-performance Rydberg atom-based AM receivers.
Rydberg atomic quantum receivers (RAQRs) recently gained significant interest. However, their impairments characterisation, which is critical for practical deployments, remains under-examined. In this paper, we evaluate how deviations in five operational parameters (atomic density, EIT linewidth, local oscillator (LO) amplitude, laser frequency, and probe power) impact the signal-to-noise ratio (SNR), third-order intercept (IIP3), 1 dB compression (P1 dB)\left(P_{1 \mathrm{~dB}}\right)(P1 dB​), and spurious-free dynamic range (SFDR). By expanding the atomic coherence in powers of signal amplitude, we classify deviation responses into three distinct categories. All three categories remain robust under Doppler broadening from 200μ K200 \mu \mathrm{~K}200μ K to 300 K. Crucially, the LO amplitude falls into a regime where IIP3 degrades linearly while the SNR changes only quadratically. As this linearity loss can go easily undetected during standard sensitivity checks, LO amplitude requires tightest control (+7% tolerance). We further derive two closed-form relationships governing the RAQRs. The first one features how much the SNR can be improved as atomic density increases, yielding improvement equal to or less than 20 dB for every tenfold increase in atomic density. The second one shows that a laser frequency drift of about 55 kHz reduces the SNR by an order of 1 dB.
This paper investigates a six-wave mixing (SWM)-based Rydberg atomic receiver as a wideband radio frequency (RF)-to-optical quantum transducer. Specifically, we develop an explicit baseband input-output model that bridges the RF-induced atomic coherence to the detected optical readout. Based on the exact detected SWM response, we develop a reduced-order closed-form two-pole low-pass approximation under the near-resonant weak-signal of interest, which provides an analytical insight into how the 3-dB bandwidth is manipulated by the dressed higher-level atomic dynamics and optical/RF parameters. The validity range of this approximation is then quantified to clarify the operating conditions under which this reduced-order model accurately represents the exact SWM response. We further characterize the linear dynamic range by employing the 1-dB compression point (P1dB) and the input-referred third-order intercept point (IIP3), unveiling a communication-compatible characterization of the bandwidth-sensitivity-linearity trade-off. Extensive simulation results demonstrate that SWM can achieve a 3-dB bandwidth of approximately 10 MHz while maintaining favorable linearity and sensitivity under the strict low-pass condition. The comparison with the EIT regime indicates that the two schemes should be treated as complementary rather than universally ordered. From an engineering perspective, the preferred SWM operating region is therefore not the one with the largest bandwidth, but the one that simultaneously provides a large bandwidth, acceptable sensitivity, favorable linearity, and low-pass regularity.