Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2412.08811

TLS and Quasiparticle Loss in Thin-Film Aluminum CPW Resonators: A Modified Model and Design Implications

Carolyn G. Volpert, Emily M. Barrentine, Alberto D. Bolatto, Ari-David Brown, Jake Connors, Thomas Essinger-Hileman, Larry A. Hess, Vilem Mikula, Stevenson, Thomas R., Eric R. Switzer

Published Dec 11, 2024• 0 citations
arXivHTMLPDF

Abstract

As superconducting kinetic inductance detectors (KIDs) continue to grow in popularity for sensitive submillimeter detection and other applications, there is a drive to advance toward lower-loss devices. We present measurements of diagnostic thin-film aluminum coplanar waveguide (CPW) resonators designed to inform ongoing KID development at NASA Goddard Space Flight Center. The resonance frequencies span $f_0$ = 3.5-4 GHz and include quarter-wave and half-wave resonators with varying coupling capacitor designs. We present measurements of the device film properties and an analysis of the dominant mechanisms of loss in the resonators measured in a dark environment, demonstrating quality factors of $Q_i^{-1} \approx 3.64-8.57\ \times 10^{-8}$. We observe an enhanced level of suppression in the loss contributions from two-level systems (TLS) at intermediate-to-high read powers, and a regime at these powers and low temperatures where contributions from intrinsic processes $Q_i^{-1}$,other dominate the total loss. We also observe deviations from the standard TLS loss model at low powers and temperatures below 60 mK, and use a modified model to describe this behavior.

DOI
10.48550/arxiv.2412.08811

Related papers

Coherence Time Enhancement of Interacting Two-Level Systems in Aluminum Superconducting Resonators

Tamin Tai, Jingnan Cai, Steven M. Anlage

Superconducting resonators are widely used in many applications such as qubit readout for quantum computing applications, and kinetic inductance detectors. These resonators are susceptible to numerous loss and noise mechanisms under microwave excitation, especially the dissipation due to non-equilibrium quasi-particles and two-level systems (TLS), which can result in a decrease of the superconducting intrinsic quality factor ($Q_i$) in high quality superconducting resonators. Particularly in the few-photon and low temperature (T) regime, TLS losses can become a dominant loss mechanism. In this study, novel aluminum half-wavelength resonators are investigated, focusing on the loss properties at extra-low power and low temperature. An unusual increase of $Q_i(T)$ with deceasing temperature is observed. This behavior is attributed to the increase of TLS coherence time ($T_2$) at ultra-low temperatures and powers. This $T_2$ increase is consistent with other work on resonant frequency noise in resonators and measurements of individual TLS, and likely arises from interacting TLS in the aluminum half-wavelength resonators.

•Sep 24, 2021•1 citation

Power and temperature dependent model for high Q superconductor resonators

Ashish Alexander, Christopher Weddle, Christopher J. K. Richardson

Measuring the internal quality factor of coplanar waveguide superconducting resonators is an established method of determining small losses in superconducting devices. Often, resonator losses are attributed to two-level system (TLS) defects using a power dependent model for the quality factor. However, excess non-equilibrium quasiparticles can also limit the quality factor of superconducting resonators. Here, a two-temperature, power and temperature dependent model is used to evaluate resonator losses for titanium nitride and aluminum coplanar waveguide resonators with loss tangents of 10−5–10−6. This model enables a set of parameters to describe both the internal quality factor and fractional frequency shift of the resonator across a broad range of average cavity photon numbers, from 1 to 106, and temperatures between those limited by the experimental apparatus near 50 mK and thermal quasiparticle dominated. The presented model also offers potential insight into observing the temperature and power dependence of TLS–TLS interactions in these resonators.

arXiv:2205.06291•APL Quantum•Jul 23, 2025•9 citations

Nonequilibrium behaviour and quasiparticle heating in thin film superconducting microwave resonators

Tejas Guruswamy

In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.

•Dec 20, 2017•8 citations

Electromagnetic Properties of Aluminum-Based Bilayers for Kinetic Inductance Detectors

Gensheng Wang, Peter S. Barry, T. Cecil +7 more

The complex conductivity of a superconducting thin film is related to the quasiparticle density, which depends on the physical temperature and can also be modified by external pair breaking with photons and phonons. This relationship forms the underlying operating principle of Kinetic Inductance Detectors (KIDs), where the detection threshold is governed by the superconducting energy gap. We investigate the electromagnetic properties of thin-film aluminum that is proximitized with either a normal metal layer of copper or a superconducting layer with a lower$T_{C}$, such as iridium, in order to extend the operating range of KIDs. Using the Usadel equations along with the Nam expressions for complex conductivity, we calculate the density of states and the complex conductivity of the resulting bilayers to understand the dependence of the pair breaking threshold, surface impedance, and intrinsic quality factor of superconducting bilayers on the relative film thicknesses. The calculations and analyses provide theoretical insights in designing aluminum-based bilayer kinetic inductance detectors for detection of microwave photons and athermal phonons at the frequencies well below the pair breaking threshold of a pure aluminum film.

arXiv:2304.00431•IEEE Transactions on Applied Superconductivity•Feb 16, 2023•1 citation

Power Handling and Responsivity of Submicron Wide Superconducting Coplanar Waveguide Resonators

R. M. J. Janssen, Akira Endo, J. J. A. Baselmans +3 more

The sensitivity of microwave kinetic inductance detectors (MKIDs) based on coplanar waveguides (CPWs) needs to be improved by at least an order of magnitude to satisfy the requirements for space-based terahertz astronomy. Our aim is to investigate if this can be achieved by reducing the width of the CPW to much below what has typically been made using optical lithography (>1 μm). CPW resonators with a central line width as narrow as 300 nm were made in NbTiN using electron beam lithography and reactive ion etching. In a systematic study of quarter-wave CPW resonators with varying widths it is shown that the behavior of responsivity, noise and power handling as a function of width continues down to 300 nm. This encourages the development of narrow KIDs using Al in order to improve their sensitivity.

arXiv:1206.0579•Journal of Low Temperature Physics•Jan 19, 2012•6 citations

Analysis of Normal and Superconducting Coplanar Waveguides in Radio Astronomy

Kim Ho Yeap

In terahertz radio astronomy, superconducting coplanar waveguide resonators have been commonly applied in Kinetic Inductance Detectors (KIDs) to measure the absorption of photon energy in the millimeter and submillimeter bands. Here, we present an analysis on the performance of superconducting niobium coplanar waveguides (CPWs). To compute the loss in a superconducting CPW, we have incorporated the complex conductivity developed by Matis and Bardeen based on the superconducting BCS theory, into the CPW loss equation. We have made a comparison between the loss in a CPW at room temperature with that below the critical temperature Tc of the superconductor. It can be observed that at frequencies below the gap frequency fg, the low in the superconducting CPW is significantly lower than that in a normal CPW. Above fg, however, the material loses its superconductivity and the loss in both temperatures becomes comparable. In our analysi, we have also shown that the loss decreases as the gap bewteen the strip and groundplane becomes wider. Hence, with careful design, the loss in a CPW can actually be minimized.

•Oct 19, 2011•5 citations
As superconducting kinetic inductance detectors (KIDs) continue to grow in popularity for sensitive submillimeter detection and other applications, there is a drive to advance toward lower-loss devices. We present measurements of diagnostic thin-film aluminum coplanar waveguide (CPW) resonators designed to inform ongoing KID development at NASA Goddard Space Flight Center. The resonance frequencies span f0f_0f0​ = 3.5-4 GHz and include quarter-wave and half-wave resonators with varying coupling capacitor designs. We present measurements of the device film properties and an analysis of the dominant mechanisms of loss in the resonators measured in a dark environment, demonstrating quality factors of Qi−1≈3.64−8.57 ×10−8Q_i^{-1} \approx 3.64-8.57\ \times 10^{-8}Qi−1​≈3.64−8.57 ×10−8. We observe an enhanced level of suppression in the loss contributions from two-level systems (TLS) at intermediate-to-high read powers, and a regime at these powers and low temperatures where contributions from intrinsic processes Qi−1Q_i^{-1}Qi−1​,other dominate the total loss. We also observe deviations from the standard TLS loss model at low powers and temperatures below 60 mK, and use a modified model to describe this behavior.
Superconducting resonators are widely used in many applications such as qubit readout for quantum computing applications, and kinetic inductance detectors. These resonators are susceptible to numerous loss and noise mechanisms under microwave excitation, especially the dissipation due to non-equilibrium quasi-particles and two-level systems (TLS), which can result in a decrease of the superconducting intrinsic quality factor (QiQ_iQi​) in high quality superconducting resonators. Particularly in the few-photon and low temperature (T) regime, TLS losses can become a dominant loss mechanism. In this study, novel aluminum half-wavelength resonators are investigated, focusing on the loss properties at extra-low power and low temperature. An unusual increase of Qi(T)Q_i(T)Qi​(T) with deceasing temperature is observed. This behavior is attributed to the increase of TLS coherence time (T2T_2T2​) at ultra-low temperatures and powers. This T2T_2T2​ increase is consistent with other work on resonant frequency noise in resonators and measurements of individual TLS, and likely arises from interacting TLS in the aluminum half-wavelength resonators.
Measuring the internal quality factor of coplanar waveguide superconducting resonators is an established method of determining small losses in superconducting devices. Often, resonator losses are attributed to two-level system (TLS) defects using a power dependent model for the quality factor. However, excess non-equilibrium quasiparticles can also limit the quality factor of superconducting resonators. Here, a two-temperature, power and temperature dependent model is used to evaluate resonator losses for titanium nitride and aluminum coplanar waveguide resonators with loss tangents of 10−5–10−6. This model enables a set of parameters to describe both the internal quality factor and fractional frequency shift of the resonator across a broad range of average cavity photon numbers, from 1 to 106, and temperatures between those limited by the experimental apparatus near 50 mK and thermal quasiparticle dominated. The presented model also offers potential insight into observing the temperature and power dependence of TLS–TLS interactions in these resonators.
In this thesis I describe work on developing theoretical and numerical models of supercon- ducting thin-film microwave resonators. Superconducting resonators are used in a variety of applications, one of which is as kinetic inductance detectors (KIDs). KIDs are ultra-low noise, highly sensitive, multiplexable detectors, with uses in a wide variety of fields including astrophysics, medical imaging, and particle physics. Resonators are also crucial for supercon- ducting qubit readout, superconducting mixers and parametric amplifiers, and as multiplexers for other devices. The results described in this thesis apply to all thin film resonators, but are primarily described in the context of KIDs. I develop models of how constant absorbed power affects superconducting thin films, driving them out of thermal equilibrium with the bath. Using the Chang & Scalapino equations, I calculate numerically the steady-state quasiparticle and phonon distributions for various sources of power (sub-gap and above-gap photons and phonons, single frequency and broadband). Many new results emerge, a few of which are: the quasiparticle heating effects of microwave power, explaining the experimentally measured saturation of resonator performance; the frequency dependence of the quasiparticle generation efficiency in the sub-mm wavelength range; and the importance of phonon trapping in thin films at low temperatures. I then use these nonequilibrium results in higher-level device models. Starting from a generic framework for resonators, I present and implement a model of a KID with variable thermal isolation. I calculate the effects of quasiparticle heating on both the large-signal and small-signal behaviour, highlighting the effects of electrothermal feedback caused by readout power. Electrothermal feedback is shown to be able to increase or decrease the magnitude and bandwidth of the responsivity and noise, depending on the operating point. Finally, I propose an experimental measurement of quasiparticle heating effects in a new device – a four-port ring resonator. In such a device, unlike in the standard two-port resonator, the device can be heated and read out independently. I develop detailed models for the thermal and electrical behaviour of these devices, and suggest a scheme by which the quasiparticle heating effects of microwave power, predicted in this thesis, can be measured.
The complex conductivity of a superconducting thin film is related to the quasiparticle density, which depends on the physical temperature and can also be modified by external pair breaking with photons and phonons. This relationship forms the underlying operating principle of Kinetic Inductance Detectors (KIDs), where the detection threshold is governed by the superconducting energy gap. We investigate the electromagnetic properties of thin-film aluminum that is proximitized with either a normal metal layer of copper or a superconducting layer with a lowerTCT_{C}TC​, such as iridium, in order to extend the operating range of KIDs. Using the Usadel equations along with the Nam expressions for complex conductivity, we calculate the density of states and the complex conductivity of the resulting bilayers to understand the dependence of the pair breaking threshold, surface impedance, and intrinsic quality factor of superconducting bilayers on the relative film thicknesses. The calculations and analyses provide theoretical insights in designing aluminum-based bilayer kinetic inductance detectors for detection of microwave photons and athermal phonons at the frequencies well below the pair breaking threshold of a pure aluminum film.
The sensitivity of microwave kinetic inductance detectors (MKIDs) based on coplanar waveguides (CPWs) needs to be improved by at least an order of magnitude to satisfy the requirements for space-based terahertz astronomy. Our aim is to investigate if this can be achieved by reducing the width of the CPW to much below what has typically been made using optical lithography (>1 μm). CPW resonators with a central line width as narrow as 300 nm were made in NbTiN using electron beam lithography and reactive ion etching. In a systematic study of quarter-wave CPW resonators with varying widths it is shown that the behavior of responsivity, noise and power handling as a function of width continues down to 300 nm. This encourages the development of narrow KIDs using Al in order to improve their sensitivity.
In terahertz radio astronomy, superconducting coplanar waveguide resonators have been commonly applied in Kinetic Inductance Detectors (KIDs) to measure the absorption of photon energy in the millimeter and submillimeter bands. Here, we present an analysis on the performance of superconducting niobium coplanar waveguides (CPWs). To compute the loss in a superconducting CPW, we have incorporated the complex conductivity developed by Matis and Bardeen based on the superconducting BCS theory, into the CPW loss equation. We have made a comparison between the loss in a CPW at room temperature with that below the critical temperature Tc of the superconductor. It can be observed that at frequencies below the gap frequency fg, the low in the superconducting CPW is significantly lower than that in a normal CPW. Above fg, however, the material loses its superconductivity and the loss in both temperatures becomes comparable. In our analysi, we have also shown that the loss decreases as the gap bewteen the strip and groundplane becomes wider. Hence, with careful design, the loss in a CPW can actually be minimized.