Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2411.02749 · IEEE Transactions on Applied Superconductivity

Extraction and Simulation of the Impact of Flux Trapping in Moats on AC-Biased Shift Registers

Scott Meninger, Sergey K. Tolpygo

Published Jan 15, 2025• 2 citations
arXivHTMLPDF

Abstract

Moats in superconducting ground planes are used to trap magnetic flux away from sensitive parts of superconductor integrated circuits. We simulate the effect of magnetic flux trapped in moats on the operating margins of ac-biased SFQ shift registers (ShReg) with two ground planes for various congruent moat geometries, moat sizes, locations in the ShReg cells, number and polarity of the trapped fluxons. Using inductance extractor InductEx, we extract mutual couplings between the moats and the ShReg inductors and include them in the refined netlist. Then we use JoSim to simulate the circuit operation and find the threshold ac clock amplitude above which the register starts to operate correctly. The relative change in this threshold is used to characterize the influence of flux trapping on the circuit operation. Monte-Carlo simulations are used to investigate the effect of the circuit parameter variations on the statistics of the threshold, using the standard deviation of the Josephson junction critical current and of the circuit inductance extracted from the fabrication process control monitors. The obtained distributions are compared with the independently measured distributions of the threshold amplitude for the individual cells of an ac-biased shift registers with 108,500 Josephson junctions. The results show that flux trapping in properly designed moats has a very small effect on the operation margins of the large-scale shift registers, whereas the main contribution to the cell-to-cell variation of the threshold comes from the variation of the junctions’ critical currents.

DOI
10.1109/tasc.2025.3527936

Related papers

Characterization of Flux Trapping in and Fabrication of Large-Scale Superconductor Circuits Using AC-Biased Shift Registers With 108 500 Josephson Junctions

Evan B. Golden, Neel Parmar, Vasili K. Semenov +1 more

A variety of superconductor integrated circuits composed of six ac-powered SFQ shift registers with a total of 27078 bits and 108500 Josephson junctions (JJs) per 5 mm × 5 mm chip have been designed, fabricated, and tested to characterize flux trapping, fabrication process yield, and parameter spread. The six 4513-bit registers in the circuits have a common single-phase ac clock and individual input/output drivers, allowing for their parallel testing. We have investigated flux trapping in the circuits with various geometry, size, distance between moats in active ground planes (GPs), and containing up to three additional ‘dummy’ GPs, using multiple cooldowns through the critical temperature with various cooling rates and residual magnetic fields up to ∼ 1.2 µT. For the slit-type and square moats arrayed along the sides of the register cells, we have found a negligible effect of flux sequestered in the moats on the operating margins of the registers, and a negligible probability of detrimental flux trapping outside of the moats. Circuits with 0.3-µm-wide slit moats occupying less than 2% of the circuit area were fully operational in 100% of cooldowns, supporting the viability of a very large-scale integration of superconductor digital circuits. We have also found a strong enhancement of flux trapping outside the moats in circuits with closely spaced GPs and determined a critical distance,${{{\boldsymbol{t}}}_{\boldsymbol{c}}} \approx $0.6 µm, between them. The presence of two or more GPs spaced below thetcrendered the circuits nonoperational in 100% of cooldowns. We have measured 30 chips with over 3M JJs and determined individual cell operating margins in 138 registers to characterize the fabrication-related parameter spread and detect fabrication defects and flux-trapping events. By finding outlier bit-cells in the statistical distribution of the individual cell margins, we detected about one fabrication defect per million JJs, in most cases causing magnetic flux trapping in the affected cell.The circuits have been fabricated in the SFQ5ee fabrication process at MIT Lincoln Laboratory (MIT LL).

arXiv:2501.03343•IEEE Transactions on Applied Superconductivity•Jan 22, 2025•8 citations

AC-Biased Shift Registers as Fabrication Process Benchmark Circuits and Flux Trapping Diagnostic Tool

Vasili K. Semenov, Yuri A. Polyakov, Sergey K. Tolpygo

We develop an ac-biased shift register introduced in our previous work (V. K. Semenov et al., IEEE Trans. Appl. Supercond., vol. 25, no. 3, 1301507, June 2015) into a benchmark circuit for evaluation of superconductor electronics fabrication technology. The developed testing technique allows for extracting margins of all individual cells in the shift register, which in turn makes it possible to estimate statistical distribution of Josephson junctions (JJs) in the circuit. We applied this approach to successfully test registers having 8-, 16-, 36-, and 202 thousand cells and, respectively, about 33-, 65-, 144-, and 809 thousand JJs. The circuits were fabricated at MIT Lincoln Laboratory, using a fully planarized process, 0.4-μm inductor linewidth and 1.33 × 106cm-2junction density. They are presently the largest operational superconducting SFQ circuits ever made. The developed technique distinguishes between “hard” defects (fabrication-related) and “soft” defects (measurement-related) and locates them in the circuit. The “soft” defects are specific to superconducting circuits and caused by magnetic flux trapping either inside the active cells or in the dedicated flux-trapping moats near the cells. The number and distribution of “soft” defects depend on the ambient magnetic field and vary with thermal cycling even if done in the same magnetic environment.

arXiv:1701.03837•IEEE Transactions on Applied Superconductivity•Feb 15, 2017•56 citations

Flux trapping experiments to verify simulation models

Kyle Jackman, Coenrad Johann Fourie

Abstract Flux trapping in superconducting integrated circuits cause circuits to operate with reduced margins, or to fail completely. Moats are used in superconducting ground planes to create low energy locations for flux trapping. Moat design and placement strategies have been presented before, and several experiments published to evaluate moat efficiency. Although fluxons can be steered to moats to prevent trapping in or near Josephson junctions or inductive interconnects, the flux in a moat couples to nearby structures and induces dc currents in superconducting loops. In this paper, we discuss a set of numerical simulation tools for flux trapping analysis, developed under the IARPA SuperTools project. These tools are used to extract compact models for magnetic flux trapped in moats, including the magnetic coupling to superconducting structures. An open-source superconducting transient simulation engine, called JoSIM, is used to simulate these compact models. To evaluate the magnetic coupling of different moat configurations, we developed a set of a flux linkage experiments. Test structures were designed for the multi-layer MIT Lincoln Laboratory SFQ5ee process that allow for flux insertion into moats of different configurations. From experimental results we measure the effects of trapped flux, in different moat structures, on SQUID parameters and use the results to validate the compact models used by our tools.

Superconductor Science and Technology•Jul 20, 2020•14 citations

Moat-guarded Josephson SQUIDs

Stuart Bermon, Tushar R. Gheewala

We report experimental investigations of a simple structure, called a moat, which significantly reduces the probability of flux-trapping in Josephson SQUIDs. Proper operation of Josephson logic and memory circuits requires that the SQUIDs be free of stray magnetic flux that may become trapped in the superconducting groundplane upon cooling through the critical temperature. The problem is particularly severe for so-called holey SQUIDs which rely on holes in the groundplane to obtain suitably large device inductances. Moats are rectangular channels in the groundplane surrounding the SQUID's which provide preferred sites for trapping flux, thus preventing such flux from coupling to the SQUID. We have measured the effectiveness of moats by monitoring the flux trapped in the moats and comparing it to the flux trapped in the associated SQUID as a function of applied field. The number of flux quanta in the moat is determined by measuring the shift of the threshold curve of a two-junction SQUID coupled to the moat. The data indicates that at fields on the order of a mG, moats reduce the sensitivity of holey SQUIDs to trapped flux by at least several orders of magnitude. As the chips are cooled through Tc, transient magnetic fields are produced in the metallic sample holder parts surrounding the chip by thermal-gradient-induced EMF's. The effects of such magnetic fields on the flux trapping behaviour of the SQUIDs are also reported.

IEEE Transactions on Magnetics•May 1, 1983•64 citations

Characterization of Adiabatic Quantum-Flux-Parametrons in the MIT LL SFQ5ee+ Process

Sergey K. Tolpygo, Evan B. Golden, Christopher Lawrence Ayala +4 more

Adiabatic quantum-flux-parametron (AQFP) superconductor logic is a proven energy-efficient digital technology for various applications. To address the scalability challenges of this technology, we investigated AQFP shift registers with the AQFP footprint area reduced by 25% with respect to prior work and with the >2× denser overall circuit designs obtained by eliminating the previously used free space between the AQFPs. We also investigated AQFP cells with different designs of flux trapping moats in the superconducting ground plane as well as compact AQFP cells that took advantage of the smaller feature sizes available in the new fabrication process, SFQ5ee+, at MIT Lincoln Laboratory (MIT LL). This new process features nine planarized Nb layers with a 0.25 μm minimum linewidth. The fabricated circuits were tested in a liquid He immersion probe and a commercial closed-cycle cryocooler using a controlled cooling rate through the superconducting critical temperature,Tc. Using multiple thermal cycles, we investigated flux trapping in the dense AQFP shift registers as well as in the registers using the old (sparse) AQFP designs at two levels of the residual magnetic field, about 0.53 μT and about 1.2 μT. The sparse designs demonstrated 95% to almost 100% probability of operation after the cooldown and very wide operation margins, although the flux trapping probability was increasing with circuit complexities. The margins were similarly wide in the newer dense designs, but flux trapping probability that rendered the registers nonoperational was significantly, by an order of magnitude, higher in these denser circuits and was also very sensitive to the moats' shape and location. Our findings indicate that AQFP circuits are amendable to increasing the scale of integration and further densification, but a careful moat design and optimization are required to reduce flux trapping effects in the dense AQFP circuits.

arXiv:2411.04045•IEEE Transactions on Applied Superconductivity•Jan 6, 2025•6 citations

Influence of Magnetic Flux Trapped in Moats on Superconducting Integrated Circuit Operation

Yuki Yamanashi, Hibiki Imai, Nobuyuki Yoshikawa

The influence of a trapped flux quantum in a superconducting ground plane hole, called a moat, on superconducting circuit operation was analyzed. We devised a calculation model to estimate the magnetic flux threading a signal line of a superconducting integrated circuit by the trapped flux quantum in a moat placed near the signal line, by using a conventional inductance extraction tool. Assuming one flux quantum trapped in the moat, the dependence of the magnetic flux threading the signal line on the distance between the moat and the signal line were calculated. We measured the flux linkage by measuring the modulation of the I-V characteristic of a dc-SQUID with a moat near the SQUID implemented by using the 2.5 kA/cm2Nb standard process. The measured flux linkage agrees well with the analysis results using the devised calculation model. When the distance between the 1 μm × 10 μm moat and the SQUID, the signal line size of which corresponds to the typical inductance of an adiabatic flux quantum parametron (AQFP) is 1 μm and one flux quantum is trapped in the moat, the measured magnetic flux linkage threads the signal line was approximately 1.2% of the flux quantum. This flux linkage induces approximately 4% deterioration of the device margin of the AQFP. The devised calculation model and experimental results provide useful information for designing highly integrated future superconducting integrated circuits.

IEEE Transactions on Applied Superconductivity•May 18, 2018•8 citations
Moats in superconducting ground planes are used to trap magnetic flux away from sensitive parts of superconductor integrated circuits. We simulate the effect of magnetic flux trapped in moats on the operating margins of ac-biased SFQ shift registers (ShReg) with two ground planes for various congruent moat geometries, moat sizes, locations in the ShReg cells, number and polarity of the trapped fluxons. Using inductance extractor InductEx, we extract mutual couplings between the moats and the ShReg inductors and include them in the refined netlist. Then we use JoSim to simulate the circuit operation and find the threshold ac clock amplitude above which the register starts to operate correctly. The relative change in this threshold is used to characterize the influence of flux trapping on the circuit operation. Monte-Carlo simulations are used to investigate the effect of the circuit parameter variations on the statistics of the threshold, using the standard deviation of the Josephson junction critical current and of the circuit inductance extracted from the fabrication process control monitors. The obtained distributions are compared with the independently measured distributions of the threshold amplitude for the individual cells of an ac-biased shift registers with 108,500 Josephson junctions. The results show that flux trapping in properly designed moats has a very small effect on the operation margins of the large-scale shift registers, whereas the main contribution to the cell-to-cell variation of the threshold comes from the variation of the junctions’ critical currents.
A variety of superconductor integrated circuits composed of six ac-powered SFQ shift registers with a total of 27078 bits and 108500 Josephson junctions (JJs) per 5 mm × 5 mm chip have been designed, fabricated, and tested to characterize flux trapping, fabrication process yield, and parameter spread. The six 4513-bit registers in the circuits have a common single-phase ac clock and individual input/output drivers, allowing for their parallel testing. We have investigated flux trapping in the circuits with various geometry, size, distance between moats in active ground planes (GPs), and containing up to three additional ‘dummy’ GPs, using multiple cooldowns through the critical temperature with various cooling rates and residual magnetic fields up to ∼ 1.2 µT. For the slit-type and square moats arrayed along the sides of the register cells, we have found a negligible effect of flux sequestered in the moats on the operating margins of the registers, and a negligible probability of detrimental flux trapping outside of the moats. Circuits with 0.3-µm-wide slit moats occupying less than 2% of the circuit area were fully operational in 100% of cooldowns, supporting the viability of a very large-scale integration of superconductor digital circuits. We have also found a strong enhancement of flux trapping outside the moats in circuits with closely spaced GPs and determined a critical distance,${{{\boldsymbol{t}}}_{\boldsymbol{c}}} \approx $0.6 µm, between them. The presence of two or more GPs spaced below thetcrendered the circuits nonoperational in 100% of cooldowns. We have measured 30 chips with over 3M JJs and determined individual cell operating margins in 138 registers to characterize the fabrication-related parameter spread and detect fabrication defects and flux-trapping events. By finding outlier bit-cells in the statistical distribution of the individual cell margins, we detected about one fabrication defect per million JJs, in most cases causing magnetic flux trapping in the affected cell.The circuits have been fabricated in the SFQ5ee fabrication process at MIT Lincoln Laboratory (MIT LL).
We develop an ac-biased shift register introduced in our previous work (V. K. Semenov et al., IEEE Trans. Appl. Supercond., vol. 25, no. 3, 1301507, June 2015) into a benchmark circuit for evaluation of superconductor electronics fabrication technology. The developed testing technique allows for extracting margins of all individual cells in the shift register, which in turn makes it possible to estimate statistical distribution of Josephson junctions (JJs) in the circuit. We applied this approach to successfully test registers having 8-, 16-, 36-, and 202 thousand cells and, respectively, about 33-, 65-, 144-, and 809 thousand JJs. The circuits were fabricated at MIT Lincoln Laboratory, using a fully planarized process, 0.4-μm inductor linewidth and 1.33 × 106cm-2junction density. They are presently the largest operational superconducting SFQ circuits ever made. The developed technique distinguishes between “hard” defects (fabrication-related) and “soft” defects (measurement-related) and locates them in the circuit. The “soft” defects are specific to superconducting circuits and caused by magnetic flux trapping either inside the active cells or in the dedicated flux-trapping moats near the cells. The number and distribution of “soft” defects depend on the ambient magnetic field and vary with thermal cycling even if done in the same magnetic environment.
Abstract Flux trapping in superconducting integrated circuits cause circuits to operate with reduced margins, or to fail completely. Moats are used in superconducting ground planes to create low energy locations for flux trapping. Moat design and placement strategies have been presented before, and several experiments published to evaluate moat efficiency. Although fluxons can be steered to moats to prevent trapping in or near Josephson junctions or inductive interconnects, the flux in a moat couples to nearby structures and induces dc currents in superconducting loops. In this paper, we discuss a set of numerical simulation tools for flux trapping analysis, developed under the IARPA SuperTools project. These tools are used to extract compact models for magnetic flux trapped in moats, including the magnetic coupling to superconducting structures. An open-source superconducting transient simulation engine, called JoSIM, is used to simulate these compact models. To evaluate the magnetic coupling of different moat configurations, we developed a set of a flux linkage experiments. Test structures were designed for the multi-layer MIT Lincoln Laboratory SFQ5ee process that allow for flux insertion into moats of different configurations. From experimental results we measure the effects of trapped flux, in different moat structures, on SQUID parameters and use the results to validate the compact models used by our tools.
We report experimental investigations of a simple structure, called a moat, which significantly reduces the probability of flux-trapping in Josephson SQUIDs. Proper operation of Josephson logic and memory circuits requires that the SQUIDs be free of stray magnetic flux that may become trapped in the superconducting groundplane upon cooling through the critical temperature. The problem is particularly severe for so-called holey SQUIDs which rely on holes in the groundplane to obtain suitably large device inductances. Moats are rectangular channels in the groundplane surrounding the SQUID's which provide preferred sites for trapping flux, thus preventing such flux from coupling to the SQUID. We have measured the effectiveness of moats by monitoring the flux trapped in the moats and comparing it to the flux trapped in the associated SQUID as a function of applied field. The number of flux quanta in the moat is determined by measuring the shift of the threshold curve of a two-junction SQUID coupled to the moat. The data indicates that at fields on the order of a mG, moats reduce the sensitivity of holey SQUIDs to trapped flux by at least several orders of magnitude. As the chips are cooled through Tc, transient magnetic fields are produced in the metallic sample holder parts surrounding the chip by thermal-gradient-induced EMF's. The effects of such magnetic fields on the flux trapping behaviour of the SQUIDs are also reported.
Adiabatic quantum-flux-parametron (AQFP) superconductor logic is a proven energy-efficient digital technology for various applications. To address the scalability challenges of this technology, we investigated AQFP shift registers with the AQFP footprint area reduced by 25% with respect to prior work and with the >2× denser overall circuit designs obtained by eliminating the previously used free space between the AQFPs. We also investigated AQFP cells with different designs of flux trapping moats in the superconducting ground plane as well as compact AQFP cells that took advantage of the smaller feature sizes available in the new fabrication process, SFQ5ee+, at MIT Lincoln Laboratory (MIT LL). This new process features nine planarized Nb layers with a 0.25 μm minimum linewidth. The fabricated circuits were tested in a liquid He immersion probe and a commercial closed-cycle cryocooler using a controlled cooling rate through the superconducting critical temperature,Tc. Using multiple thermal cycles, we investigated flux trapping in the dense AQFP shift registers as well as in the registers using the old (sparse) AQFP designs at two levels of the residual magnetic field, about 0.53 μT and about 1.2 μT. The sparse designs demonstrated 95% to almost 100% probability of operation after the cooldown and very wide operation margins, although the flux trapping probability was increasing with circuit complexities. The margins were similarly wide in the newer dense designs, but flux trapping probability that rendered the registers nonoperational was significantly, by an order of magnitude, higher in these denser circuits and was also very sensitive to the moats' shape and location. Our findings indicate that AQFP circuits are amendable to increasing the scale of integration and further densification, but a careful moat design and optimization are required to reduce flux trapping effects in the dense AQFP circuits.
The influence of a trapped flux quantum in a superconducting ground plane hole, called a moat, on superconducting circuit operation was analyzed. We devised a calculation model to estimate the magnetic flux threading a signal line of a superconducting integrated circuit by the trapped flux quantum in a moat placed near the signal line, by using a conventional inductance extraction tool. Assuming one flux quantum trapped in the moat, the dependence of the magnetic flux threading the signal line on the distance between the moat and the signal line were calculated. We measured the flux linkage by measuring the modulation of the I-V characteristic of a dc-SQUID with a moat near the SQUID implemented by using the 2.5 kA/cm2Nb standard process. The measured flux linkage agrees well with the analysis results using the devised calculation model. When the distance between the 1 μm × 10 μm moat and the SQUID, the signal line size of which corresponds to the typical inductance of an adiabatic flux quantum parametron (AQFP) is 1 μm and one flux quantum is trapped in the moat, the measured magnetic flux linkage threads the signal line was approximately 1.2% of the flux quantum. This flux linkage induces approximately 4% deterioration of the device margin of the AQFP. The devised calculation model and experimental results provide useful information for designing highly integrated future superconducting integrated circuits.