Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2410.11721 · Nature Communications

Supercurrent time division multiplexing with solid-state integrated hybrid superconducting electronics

Alessandro Paghi, Laura Borgongino, Simone Tortorella, Giorgio De Simoni, Elia Strambini, Lucia Sorba, Francesco Giazotto

Published Sep 26, 2025• 7 citations
arXivHTMLPDF

Abstract

Time-division multiplexing of cryogenic signals is a promising approach to reduce space requirements, shorten cooldown times, and increase the number of quantum devices measured per cooldown. We demonstrate time-division multiplexing of non-dissipative supercurrents using voltage-controlled hybrid superconducting demultiplexers. These chips integrate superconducting Josephson Field Effect Transistors including Al superconducting electrodes, proximitized semiconducting InAs channels, and hafnium oxide gate insulators. Each transistor fully suppresses the switching current and increases the resistance 20 times under a gate voltage of −4.5 V. A demultiplexer with one input and eight outputs showed a non-dissipative input range of ±2 μA, operating up to 100 MHz in signal frequency, and 100 kHz in switching frequency at 50 mK. It achieved near-zero insertion loss in the superconducting state and an $$\frac{{ON}}{{OFF}}$$ ratio of 17.5 dB. By optimizing the signal layout, the operation was extended up to 4 GHz using a demultiplexer with two outputs. The authors report a 1-input-8-ouput superconducting demultiplexer consisting of 14 Al-InAs-Al Josephson Field Effect Transistors, enabling time-division multiplexing of non-dissipative current up to several GHz. This strategy can reduce the number of I/O lines to drive cryogenic electrical devices in quantum applications.

DOI
10.1038/s41467-025-62931-3

Related papers

CryoCMOS RF multiplexer for superconducting qubit control, readout and flux biasing at millikelvin temperatures with picowatt power consumption

Liam Fallik, Sriram Balamurali, Alican Caglar +12 more

Large-scale cryogenic quantum systems are constrained by an input-output bottleneck between room-temperature electronics and millikelvin stages, particularly in superconducting qubit platforms. This bottleneck is most acute for output lines, where bulky and expensive microwave components limit scalability. A promising approach for scalable characterization and testing is to perform signal multiplexing directly at the qubit plane. We demonstrate a cryogenic CMOS (cryoCMOS) RF multiplexer operating at 10 millikelvin with record-low static power consumption of 200 pW. The device provides < 2 dB insertion loss and > 30 dB isolation across DC-8 GHz. Direct connection to transmon qubits marginally affects coherence times in the range of 100 microseconds, enabling multiplexing of readout, flux and, in principle, XY drive lines. This work introduces cryoCMOS multiplexers as valuable tools for scalable, high-throughput cryogenic characterization and testing, and advances co-integrated quantum-classical control for future large-scale quantum processors.

quant-pharXiv:2603.16608•npj Quantum Information•Mar 18, 2026•0 citations

Cryogenic Time-Division-Multiplexed Voltage Control for Scalable Trapped-Ion Quantum Processors

Ryutaro Ohira, Shinichi Morisaka, Yoshinori Kurimoto +4 more

Trapped-ion quantum computers based on the quantum charge-coupled device architecture require on the order of ten trap electrodes per qubit, making the number of vacuum feedthroughs a bottleneck at the system scale. Time-division multiplexed (TDM)-based voltage control for trap electrodes provides a natural route to alleviate this constraint. However, previous studies have been limited to architectural proposals for static trap-potential compensation and room-temperature demonstrations of dynamic-electrode control, leaving cryogenic operation of TDM-based voltage control for static and dynamic electrodes experimentally unexplored. In this study, we develop and cryogenically validate TDM-based voltage control schemes for two distinct electrode classes. For static electrodes used in trap-potential compensation, we implement a 32-channel demultiplexed system operating at approximately 27~K, achieving an effective voltage update rate of 37.5~kHz with an output range of $\pm10~\mathrm{V}$ per channel. For dynamic electrodes used in ion operations, such as shuttling, we implement a four-channel demultiplexed system operating at approximately 14~K, achieving an effective voltage update rate of 1~MHz with a comparable output range. These results establish TDM-based voltage control as a practical approach for both electrode classes, providing a path for mitigating the vacuum feedthrough bottleneck in scalable trapped-ion quantum processors.

quant-pharXiv:2605.17824•Applied Physics Letters•May 19, 2026•1 citation

InAs on Insulator: A New Platform for Cryogenic Hybrid Superconducting Electronics

Alessandro Paghi, Giacomo Trupiano, Giorgio De Simoni +3 more

Abstract Superconducting circuits based on hybrid InAs Josephson Junctions (JJs) play a starring role in the design of fast and ultra‐low power consumption solid‐state quantum electronics and exploring novel physical phenomena. Conventionally, 3D substrates, 2D quantum wells (QWs), and 1D nanowires (NWs) made of InAs are employed to create superconducting circuits with hybrid JJs. Each platform has its advantages and disadvantages. Here, the InAs‐on‐insulator (InAsOI) is proposed as a groundbreaking platform for developing superconducting electronics. An epilayer of semiconducting InAs with different electron densities is grown onto an InAlAs metamorphic buffer, efficiently used as a cryogenic insulator to decouple adjacent devices electrically. JJs with various lengths and widths are fabricated employing Al as a superconductor and InAs with different electron densities. A switching current density of 7.3 µA µm−1, a critical voltage of 50‐to‐80 µV, and a critical temperature equal to that of the superconductor used are achieved. For all the JJs, the switching current follows a Fraunhofer‐like pattern with the out‐of‐plane magnetic field. These achievements enable the use of InAsOI to design and fabricate surface‐exposed Josephson Field Effect Transistors with high critical current densities and superior gating properties.

arXiv:2405.07630•Advanced Functional Materials•Nov 29, 2024•13 citations

Microwave-multiplexed qubit controller using adiabatic superconductor logic

Naoki Takeuchi, Taiki Yamae, Taro Yamashita +2 more

Abstract Cryogenic qubit controllers (QCs) are the key to build large-scale superconducting quantum processors. However, developing scalable QCs is challenging because the cooling power of a dilution refrigerator is too small (~10 μW at ~10 mK) to operate conventional logic families, such as complementary metal-oxide-semiconductor logic and superconducting single-flux-quantum logic, near qubits. Here we report on a scalable QC using an ultra-low-power superconductor logic family, namely adiabatic quantum-flux-parametron (AQFP) logic. The AQFP-based QC, referred to as the AQFP-multiplexed QC (AQFP-mux QC), produces multi-tone microwave signals for qubit control with an extremely small power dissipation of 81.8 pW per qubit. Furthermore, the AQFP-mux QC adopts microwave multiplexing to reduce the number of coaxial cables for operating the entire system. As a proof of concept, we demonstrate an AQFP-mux QC chip that produces microwave signals at two output ports through microwave multiplexing and demultiplexing. Experimental results show an output power of approximately −80 dBm and on/off ratio of ~40 dB at each output port. Basic mixing operation is also demonstrated by observing sideband signals.

arXiv:2310.06544•npj Quantum Information•Jun 3, 2024•37 citations

A fast and large bandwidth superconducting variable coupler

H.-S. Chang, K. J. Satzinger, Y. P. Zhong +8 more

Variable microwave-frequency couplers are highly useful components in classical communication systems and likely will play an important role in quantum communication applications. Conventional semiconductor-based microwave couplers have been used with superconducting quantum circuits, enabling, for example, the in situ measurements of multiple devices via a common readout chain. However, the semiconducting elements are lossy and furthermore dissipate energy when switched, making them unsuitable for cryogenic applications requiring rapid, repeated switching. Superconducting Josephson junction-based couplers can be designed for dissipation-free operation with fast switching and are easily integrated with superconducting quantum circuits. These enable on-chip, quantum-coherent routing of microwave photons, providing an appealing alternative to semiconductor switches. Here, we present and characterize a chip-based broadband microwave variable coupler, tunable over 4–8 GHz with over 1.5 GHz instantaneous bandwidth, based on the superconducting quantum interference device with two parallel Josephson junctions. The coupler is dissipation-free and features large on-off ratios in excess of 40 dB, and the coupling can be changed in about 10 ns. The simple design presented here can be readily integrated with superconducting qubit circuits and can be easily generalized to realize a four- or more port device.

arXiv:2011.09442•Applied Physics Letters•Dec 14, 2020•10 citations

Cryogenic quantum computer control signal generation using high-electron-mobility transistors

Alberto Ferraris, Eunjung Cha, Peter R. Müeller +2 more

Multiplexed local charge storage, close to quantum processors at cryogenic temperatures could generate a multitude of control signals, for electronics or qubits, in an efficient manner. Such cryogenic electronics require generating quasi-static control signals with small area footprint, low noise, high stability, low power dissipation and, ideally, in a multiplexed fashion to reduce the number of input/outputs. In this work, we integrate capacitors with cryogenic high-electron mobility transistor (HEMT) arrays and demonstrate quasi-static bias generation using gate pulses controlled in time and frequency domains. Multi-channel bias generation is also demonstrated. Operation at 4 K exhibits improved bias signal variability and greatly reduced subthreshold swing, reaching values of ~6 mV/decade. Due to the very low threshold voltage of 80 mV at 4 K and the steep subthreshold swing, these circuits can provide an advantage over the silicon-based complementary metal-oxide-semiconductor equivalents by allowing operation at significantly reduced drive bias in the low output voltage regime <1 V. Together with their high-speed operation, this makes HEMTs an attractive platform for future cryogenic signal generation electronics in quantum computers.

Communications Engineering•Oct 15, 2024•10 citations
Time-division multiplexing of cryogenic signals is a promising approach to reduce space requirements, shorten cooldown times, and increase the number of quantum devices measured per cooldown. We demonstrate time-division multiplexing of non-dissipative supercurrents using voltage-controlled hybrid superconducting demultiplexers. These chips integrate superconducting Josephson Field Effect Transistors including Al superconducting electrodes, proximitized semiconducting InAs channels, and hafnium oxide gate insulators. Each transistor fully suppresses the switching current and increases the resistance 20 times under a gate voltage of −4.5 V. A demultiplexer with one input and eight outputs showed a non-dissipative input range of ±2 μA, operating up to 100 MHz in signal frequency, and 100 kHz in switching frequency at 50 mK. It achieved near-zero insertion loss in the superconducting state and an ONOFF\frac{{ON}}{{OFF}}OFFON​ ratio of 17.5 dB. By optimizing the signal layout, the operation was extended up to 4 GHz using a demultiplexer with two outputs. The authors report a 1-input-8-ouput superconducting demultiplexer consisting of 14 Al-InAs-Al Josephson Field Effect Transistors, enabling time-division multiplexing of non-dissipative current up to several GHz. This strategy can reduce the number of I/O lines to drive cryogenic electrical devices in quantum applications.
Large-scale cryogenic quantum systems are constrained by an input-output bottleneck between room-temperature electronics and millikelvin stages, particularly in superconducting qubit platforms. This bottleneck is most acute for output lines, where bulky and expensive microwave components limit scalability. A promising approach for scalable characterization and testing is to perform signal multiplexing directly at the qubit plane. We demonstrate a cryogenic CMOS (cryoCMOS) RF multiplexer operating at 10 millikelvin with record-low static power consumption of 200 pW. The device provides < 2 dB insertion loss and > 30 dB isolation across DC-8 GHz. Direct connection to transmon qubits marginally affects coherence times in the range of 100 microseconds, enabling multiplexing of readout, flux and, in principle, XY drive lines. This work introduces cryoCMOS multiplexers as valuable tools for scalable, high-throughput cryogenic characterization and testing, and advances co-integrated quantum-classical control for future large-scale quantum processors.
Trapped-ion quantum computers based on the quantum charge-coupled device architecture require on the order of ten trap electrodes per qubit, making the number of vacuum feedthroughs a bottleneck at the system scale. Time-division multiplexed (TDM)-based voltage control for trap electrodes provides a natural route to alleviate this constraint. However, previous studies have been limited to architectural proposals for static trap-potential compensation and room-temperature demonstrations of dynamic-electrode control, leaving cryogenic operation of TDM-based voltage control for static and dynamic electrodes experimentally unexplored. In this study, we develop and cryogenically validate TDM-based voltage control schemes for two distinct electrode classes. For static electrodes used in trap-potential compensation, we implement a 32-channel demultiplexed system operating at approximately 27~K, achieving an effective voltage update rate of 37.5~kHz with an output range of ±10 V\pm10~\mathrm{V}±10 V per channel. For dynamic electrodes used in ion operations, such as shuttling, we implement a four-channel demultiplexed system operating at approximately 14~K, achieving an effective voltage update rate of 1~MHz with a comparable output range. These results establish TDM-based voltage control as a practical approach for both electrode classes, providing a path for mitigating the vacuum feedthrough bottleneck in scalable trapped-ion quantum processors.
Abstract Superconducting circuits based on hybrid InAs Josephson Junctions (JJs) play a starring role in the design of fast and ultra‐low power consumption solid‐state quantum electronics and exploring novel physical phenomena. Conventionally, 3D substrates, 2D quantum wells (QWs), and 1D nanowires (NWs) made of InAs are employed to create superconducting circuits with hybrid JJs. Each platform has its advantages and disadvantages. Here, the InAs‐on‐insulator (InAsOI) is proposed as a groundbreaking platform for developing superconducting electronics. An epilayer of semiconducting InAs with different electron densities is grown onto an InAlAs metamorphic buffer, efficiently used as a cryogenic insulator to decouple adjacent devices electrically. JJs with various lengths and widths are fabricated employing Al as a superconductor and InAs with different electron densities. A switching current density of 7.3 µA µm−1, a critical voltage of 50‐to‐80 µV, and a critical temperature equal to that of the superconductor used are achieved. For all the JJs, the switching current follows a Fraunhofer‐like pattern with the out‐of‐plane magnetic field. These achievements enable the use of InAsOI to design and fabricate surface‐exposed Josephson Field Effect Transistors with high critical current densities and superior gating properties.
Abstract Cryogenic qubit controllers (QCs) are the key to build large-scale superconducting quantum processors. However, developing scalable QCs is challenging because the cooling power of a dilution refrigerator is too small (~10 μW at ~10 mK) to operate conventional logic families, such as complementary metal-oxide-semiconductor logic and superconducting single-flux-quantum logic, near qubits. Here we report on a scalable QC using an ultra-low-power superconductor logic family, namely adiabatic quantum-flux-parametron (AQFP) logic. The AQFP-based QC, referred to as the AQFP-multiplexed QC (AQFP-mux QC), produces multi-tone microwave signals for qubit control with an extremely small power dissipation of 81.8 pW per qubit. Furthermore, the AQFP-mux QC adopts microwave multiplexing to reduce the number of coaxial cables for operating the entire system. As a proof of concept, we demonstrate an AQFP-mux QC chip that produces microwave signals at two output ports through microwave multiplexing and demultiplexing. Experimental results show an output power of approximately −80 dBm and on/off ratio of ~40 dB at each output port. Basic mixing operation is also demonstrated by observing sideband signals.
Variable microwave-frequency couplers are highly useful components in classical communication systems and likely will play an important role in quantum communication applications. Conventional semiconductor-based microwave couplers have been used with superconducting quantum circuits, enabling, for example, the in situ measurements of multiple devices via a common readout chain. However, the semiconducting elements are lossy and furthermore dissipate energy when switched, making them unsuitable for cryogenic applications requiring rapid, repeated switching. Superconducting Josephson junction-based couplers can be designed for dissipation-free operation with fast switching and are easily integrated with superconducting quantum circuits. These enable on-chip, quantum-coherent routing of microwave photons, providing an appealing alternative to semiconductor switches. Here, we present and characterize a chip-based broadband microwave variable coupler, tunable over 4–8 GHz with over 1.5 GHz instantaneous bandwidth, based on the superconducting quantum interference device with two parallel Josephson junctions. The coupler is dissipation-free and features large on-off ratios in excess of 40 dB, and the coupling can be changed in about 10 ns. The simple design presented here can be readily integrated with superconducting qubit circuits and can be easily generalized to realize a four- or more port device.
Multiplexed local charge storage, close to quantum processors at cryogenic temperatures could generate a multitude of control signals, for electronics or qubits, in an efficient manner. Such cryogenic electronics require generating quasi-static control signals with small area footprint, low noise, high stability, low power dissipation and, ideally, in a multiplexed fashion to reduce the number of input/outputs. In this work, we integrate capacitors with cryogenic high-electron mobility transistor (HEMT) arrays and demonstrate quasi-static bias generation using gate pulses controlled in time and frequency domains. Multi-channel bias generation is also demonstrated. Operation at 4 K exhibits improved bias signal variability and greatly reduced subthreshold swing, reaching values of ~6 mV/decade. Due to the very low threshold voltage of 80 mV at 4 K and the steep subthreshold swing, these circuits can provide an advantage over the silicon-based complementary metal-oxide-semiconductor equivalents by allowing operation at significantly reduced drive bias in the low output voltage regime <1 V. Together with their high-speed operation, this makes HEMTs an attractive platform for future cryogenic signal generation electronics in quantum computers.