Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2409.03356 · Applied Physics Letters

Magnetic field tunable spectral response of kinetic inductance detectors

F. Lévy-Bertrand, Martino Calvo, U. Chowdhury, A. Gómez, J. Goupy, A. Monfardini

Published Jan 27, 2025• 1 citation
arXivHTMLPDF

Abstract

We tune the onset of optical response in aluminum kinetic inductance detectors from a natural cutoff frequency of 90 GHz to 60 GHz by applying an external magnetic field. The change in the spectral response is due to the decrease in the superconducting gap, from 90 GHz at zero magnetic field to 60 GHz at a magnetic field of around 3 mT. We characterize the variation of the superconducting gap, the detector frequency shift, and the internal quality factor as a function of the applied field. In principle, the magnetic field tunable response could be used to make spectroscopic measurements. In practice, the internal quality factor behaves hysterically with the magnetic field due to the presence of vortices in the thin superconducting film. We conclude by discussing possible solutions to achieve spectroscopy measurements using kinetic inductance detectors and magnetic field.

DOI
10.1063/5.0231368

Related papers

Magnetic field dependence of the internal quality factor and noise performance of lumped-element kinetic inductance detectors

D. Flanigan, B. R. Johnson, M. H. Abitbol +8 more

We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near 150 mK. Since the thin-film aluminum has a slightly elevated critical temperature (Tc = 1.4 K), it therefore transitions before the package (Tc = 1.2 K), which also serves as a magnetic shield. On cooldown, ambient magnetic fields as small as approximately 30 µT can produce vortices in the thin-film aluminum as it transitions because the bulk aluminum package has not yet transitioned and therefore is not yet shielding. These vortices become trapped inside the aluminum package below 1.2 K and ultimately produce low internal quality factors in the thin-film superconducting resonators. We show that by controlling the strength of the magnetic field present when the thin film transitions, we can control the internal quality factor of the resonators. We also compare the noise performance with and without vortices present, and find no evidence for excess noise beyond the increase in amplifier noise, which is expected with increasing loss.

arXiv:1609.06352•Applied Physics Letters•Oct 3, 2016•21 citations

Electromagnetic Properties of Aluminum-Based Bilayers for Kinetic Inductance Detectors

Gensheng Wang, Peter S. Barry, T. Cecil +7 more

The complex conductivity of a superconducting thin film is related to the quasiparticle density, which depends on the physical temperature and can also be modified by external pair breaking with photons and phonons. This relationship forms the underlying operating principle of Kinetic Inductance Detectors (KIDs), where the detection threshold is governed by the superconducting energy gap. We investigate the electromagnetic properties of thin-film aluminum that is proximitized with either a normal metal layer of copper or a superconducting layer with a lower$T_{C}$, such as iridium, in order to extend the operating range of KIDs. Using the Usadel equations along with the Nam expressions for complex conductivity, we calculate the density of states and the complex conductivity of the resulting bilayers to understand the dependence of the pair breaking threshold, surface impedance, and intrinsic quality factor of superconducting bilayers on the relative film thicknesses. The calculations and analyses provide theoretical insights in designing aluminum-based bilayer kinetic inductance detectors for detection of microwave photons and athermal phonons at the frequencies well below the pair breaking threshold of a pure aluminum film.

arXiv:2304.00431•IEEE Transactions on Applied Superconductivity•Feb 16, 2023•1 citation

Frequency-tunable high-Q superconducting resonators via wireless control of nonlinear kinetic inductance

Mingrui Xu, Xu Han, Wei Fu +2 more

Frequency-tunable microwave resonators are in great demand especially in hybrid systems where precise frequency alignment of resonances is required. Here, we present frequency-tunable high-Q superconducting resonators fabricated from thin niobium nitride and niobium titanium nitride films. The resonant frequency is tuned by applying a magnetic field perpendicular to the hole structures in the resonator's inductor wire, whose kinetic inductance is modified by wirelessly induced DC supercurrents. A continuous in situ frequency tuning of over 300 MHz is achieved for a 10 GHz resonator with a moderate magnetic field of 1.2 mT. The planar resonator design and the noncontact tuning scheme greatly ease the fabrication complexity and can be widely applied in many hybrid systems for coupling microwave modes with other forms of excitations such as optical photons, phonons, magnons, and spins.

Applied Physics Letters•May 13, 2019•62 citations

SKIFFS: Superconducting Kinetic Inductance Field-Frequency Sensors for sensitive magnetometry in moderate background magnetic fields

Abraham T. Asfaw, Ethan Kleinbaum, Thomas Hazard +3 more

We describe sensitive magnetometry using lumped-element resonators fabricated from a superconducting thin film of NbTiN. Taking advantage of the large kinetic inductance of the superconductor, we demonstrate a continuous resonance frequency shift of 27 MHz for a change in the magnetic field of 1.8 μT within a perpendicular background field of 60 mT. By using phase-sensitive readout of microwaves transmitted through the sensors, we measure phase shifts in real time with a sensitivity of 1°/nT. We present measurements of the noise spectral density of the sensors and find that their field sensitivity is at least within one to two orders of magnitude of superconducting quantum interference devices operating with zero background field. Our superconducting kinetic inductance field-frequency sensors enable real-time magnetometry in the presence of moderate perpendicular background fields up to at least 0.2 T. Applications for our sensors include the stabilization of magnetic fields in long coherence electron spin resonance measurements and quantum computation.

arXiv:1807.09860•Applied Physics Letters•Oct 22, 2018•5 citations

Frequency-tunable superconducting resonators via nonlinear kinetic inductance

Michael R. Vissers, Johannes Hubmayr, Martin Sandberg +3 more

We have designed, fabricated, and tested a frequency-tunable high-Q superconducting resonator made from a niobium titanium nitride film. The frequency tunability is achieved by injecting a DC through a current-directing circuit into the nonlinear inductor whose kinetic inductance is current-dependent. We have demonstrated continuous tuning of the resonance frequency in a 180 MHz frequency range around 4.5 GHz while maintaining the high internal quality factor Qi > 180 000. This device may serve as a tunable filter and find applications in superconducting quantum computing and measurement. It also provides a useful tool to study the nonlinear response of a superconductor. In addition, it may be developed into techniques for measurement of the complex impedance of a superconductor at its transition temperature and for readout of transition-edge sensors.

arXiv:1507.05126•Applied Physics Letters•Aug 10, 2015•90 citations

Flux-coupled tunable superconducting resonator

Juliang Li, Peter S. Barry, Tom Cecil +6 more

We present a design and implementation of a frequency-tunable superconducting resonator. The resonance frequency tunability is achieved by flux-coupling a superconducting LC loop to a current-biased feedline; the resulting screening current leads to a change of the kinetic inductance and shift in the resonance frequency. The thin-film aluminum resonator consists of an interdigitated capacitor and thin line inductors forming a closed superconducting loop. The magnetic flux from the nearby niobium current feedline induces Meissner shielding currents in the resonator loop leading to a change in the kinetic part of the total inductance of the resonator. We demonstrate continuous frequency tuning within 160 MHz around the resonant frequency of 2.7 GHz. We show that: (1) frequency up-conversion is achieved when a kilohertz ac modulation signal is superimposed onto the dc bias resulting in sidebands to the resonator tone; (2) three-wave mixing is attained by parametrically pumping the nonlinear kinetic inductance using a strong rf pump signal in the feedline. The simple architecture is amenable to large-array multiplexing and on-chip integration with other circuit components. The concept could be applied in flux magnetometers, up-converters, and parametric amplifiers operating above 4 K when alternative high-critical-temperature material with high kinetic inductance is used.

arXiv:2312.12755•Physical Review Applied•Jul 30, 2024•9 citations
We tune the onset of optical response in aluminum kinetic inductance detectors from a natural cutoff frequency of 90 GHz to 60 GHz by applying an external magnetic field. The change in the spectral response is due to the decrease in the superconducting gap, from 90 GHz at zero magnetic field to 60 GHz at a magnetic field of around 3 mT. We characterize the variation of the superconducting gap, the detector frequency shift, and the internal quality factor as a function of the applied field. In principle, the magnetic field tunable response could be used to make spectroscopic measurements. In practice, the internal quality factor behaves hysterically with the magnetic field due to the presence of vortices in the thin superconducting film. We conclude by discussing possible solutions to achieve spectroscopy measurements using kinetic inductance detectors and magnetic field.
We present a technique for increasing the internal quality factor of kinetic inductance detectors (KIDs) by nulling ambient magnetic fields with a properly applied magnetic field. The KIDs used in this study are made from thin-film aluminum, they are mounted inside a light-tight package made from bulk aluminum, and they are operated near 150 mK. Since the thin-film aluminum has a slightly elevated critical temperature (Tc = 1.4 K), it therefore transitions before the package (Tc = 1.2 K), which also serves as a magnetic shield. On cooldown, ambient magnetic fields as small as approximately 30 µT can produce vortices in the thin-film aluminum as it transitions because the bulk aluminum package has not yet transitioned and therefore is not yet shielding. These vortices become trapped inside the aluminum package below 1.2 K and ultimately produce low internal quality factors in the thin-film superconducting resonators. We show that by controlling the strength of the magnetic field present when the thin film transitions, we can control the internal quality factor of the resonators. We also compare the noise performance with and without vortices present, and find no evidence for excess noise beyond the increase in amplifier noise, which is expected with increasing loss.
The complex conductivity of a superconducting thin film is related to the quasiparticle density, which depends on the physical temperature and can also be modified by external pair breaking with photons and phonons. This relationship forms the underlying operating principle of Kinetic Inductance Detectors (KIDs), where the detection threshold is governed by the superconducting energy gap. We investigate the electromagnetic properties of thin-film aluminum that is proximitized with either a normal metal layer of copper or a superconducting layer with a lowerTCT_{C}TC​, such as iridium, in order to extend the operating range of KIDs. Using the Usadel equations along with the Nam expressions for complex conductivity, we calculate the density of states and the complex conductivity of the resulting bilayers to understand the dependence of the pair breaking threshold, surface impedance, and intrinsic quality factor of superconducting bilayers on the relative film thicknesses. The calculations and analyses provide theoretical insights in designing aluminum-based bilayer kinetic inductance detectors for detection of microwave photons and athermal phonons at the frequencies well below the pair breaking threshold of a pure aluminum film.
Frequency-tunable microwave resonators are in great demand especially in hybrid systems where precise frequency alignment of resonances is required. Here, we present frequency-tunable high-Q superconducting resonators fabricated from thin niobium nitride and niobium titanium nitride films. The resonant frequency is tuned by applying a magnetic field perpendicular to the hole structures in the resonator's inductor wire, whose kinetic inductance is modified by wirelessly induced DC supercurrents. A continuous in situ frequency tuning of over 300 MHz is achieved for a 10 GHz resonator with a moderate magnetic field of 1.2 mT. The planar resonator design and the noncontact tuning scheme greatly ease the fabrication complexity and can be widely applied in many hybrid systems for coupling microwave modes with other forms of excitations such as optical photons, phonons, magnons, and spins.
We describe sensitive magnetometry using lumped-element resonators fabricated from a superconducting thin film of NbTiN. Taking advantage of the large kinetic inductance of the superconductor, we demonstrate a continuous resonance frequency shift of 27 MHz for a change in the magnetic field of 1.8 μT within a perpendicular background field of 60 mT. By using phase-sensitive readout of microwaves transmitted through the sensors, we measure phase shifts in real time with a sensitivity of 1°/nT. We present measurements of the noise spectral density of the sensors and find that their field sensitivity is at least within one to two orders of magnitude of superconducting quantum interference devices operating with zero background field. Our superconducting kinetic inductance field-frequency sensors enable real-time magnetometry in the presence of moderate perpendicular background fields up to at least 0.2 T. Applications for our sensors include the stabilization of magnetic fields in long coherence electron spin resonance measurements and quantum computation.
We have designed, fabricated, and tested a frequency-tunable high-Q superconducting resonator made from a niobium titanium nitride film. The frequency tunability is achieved by injecting a DC through a current-directing circuit into the nonlinear inductor whose kinetic inductance is current-dependent. We have demonstrated continuous tuning of the resonance frequency in a 180 MHz frequency range around 4.5 GHz while maintaining the high internal quality factor Qi > 180 000. This device may serve as a tunable filter and find applications in superconducting quantum computing and measurement. It also provides a useful tool to study the nonlinear response of a superconductor. In addition, it may be developed into techniques for measurement of the complex impedance of a superconductor at its transition temperature and for readout of transition-edge sensors.
We present a design and implementation of a frequency-tunable superconducting resonator. The resonance frequency tunability is achieved by flux-coupling a superconducting LC loop to a current-biased feedline; the resulting screening current leads to a change of the kinetic inductance and shift in the resonance frequency. The thin-film aluminum resonator consists of an interdigitated capacitor and thin line inductors forming a closed superconducting loop. The magnetic flux from the nearby niobium current feedline induces Meissner shielding currents in the resonator loop leading to a change in the kinetic part of the total inductance of the resonator. We demonstrate continuous frequency tuning within 160 MHz around the resonant frequency of 2.7 GHz. We show that: (1) frequency up-conversion is achieved when a kilohertz ac modulation signal is superimposed onto the dc bias resulting in sidebands to the resonator tone; (2) three-wave mixing is attained by parametrically pumping the nonlinear kinetic inductance using a strong rf pump signal in the feedline. The simple architecture is amenable to large-array multiplexing and on-chip integration with other circuit components. The concept could be applied in flux magnetometers, up-converters, and parametric amplifiers operating above 4 K when alternative high-critical-temperature material with high kinetic inductance is used.