Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2407.20433 · Journal of Physics B Atomic Molecular and Optical Physics

Rydberg atom-based microwave electrometry using polarization spectroscopy

Naomy Duarte Gomes, Vinícius M. Pepino, Ben‐Hur V. Borges, Daniel Varela Magalhães, Reginaldo de Jesus Napolitano, Manuel Alejandro Lefrán Torres, Jorge Douglas Massayuki Kondo, Luís Gustavo Marcassa

Published Oct 22, 2024• 5 citations
arXivHTMLPDF

Abstract

Abstract In this study, we investigated Rydberg atom-based microwave (MW) electrometry using polarization spectroscopy in a room-temperature vapor cell. By measuring Autler-Townes splitting in the electromagnetically induced transparency (EIT) spectrum, we determined that the minimum measurable MW electric field is approximately five times lower than conventional EIT techniques. The results are well reproduced by a full optical Bloch equation model, which takes into account all the hyperfine levels involved. Subsequently, the EIT setup was used to characterize a custom MW cylindrical lens, which increases the field at the focus by a factor of three, decreasing the minimum measurable MW electric field by the same amount. Our results indicate that the combination of polarization spectroscopy and a MW lens may enhance MW electrometry, and may allow its use as a secondary standard.

DOI
10.1088/1361-6455/ad8a34

Related papers

Microwave electrometry with Rydberg atoms in a vapor cell using microwave amplitude modulation

Jianhai Hao, Feng-Dong Jia, Yue Cui +9 more

We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagnetically-induced transparency (EIT) Autler–Townes (AT) splitting spectra obtained using amplitude modulation of the microwave (MW) electric field. In addition to the two zero-crossing points interval Δf zeros, the dispersion signal has two positive maxima with an interval defined as the shoulder interval Δf sho, which is theoretically expected to be used to measure a much weaker MW electric field. The relationship of the MW field strength E MW and Δf sho is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively. The results show that Δf sho can be used to characterize the much weaker E MW than that of Δf zeros and the traditional EIT–AT splitting interval Δf m; the minimum E MW measured by Δf sho is about 30 times smaller than that by Δf m. As an example, the minimum E MW at 9.2 GHz that can be characterized by Δf sho is 0.056 mV/cm, which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields. The proposed method can improve the weak limit and sensitivity of E MW measured by the spectral frequency interval, which is important in the direct measurement of weak E MW.

arXiv:2304.09316•Chinese Physics B•Jan 4, 2024•17 citations

Improving the spectral resolution and measurement range of quantum microwave electrometry by cold Rydberg atoms

Fei Zhou, Feng-Dong Jia, Xiubin Liu +5 more

Abstract We theoretically and experimentally studied quantum microwave electrometry in a cold atomic system using Rydberg electromagnetic induction transparency (EIT) and Autler–Townes splitting (EIT-AT splitting). In cold atoms, a spectral linewidth of ∼500 kHz for EIT was achieved owing to a significant reduction in residual Doppler width, i.e. by at least an order of magnitude, compared to that in vapor cells at room temperature. Therefore, the minimum microwave electric field intensity (E MW) that can be measured is 430 µV cm−1, which is one order higher sensitivity in the EIT-AT regime than that in vapor cells at room temperature. Unlike microwave electrometry in atomic vapor cells, EIT-AT splitting cannot be observed if E MW is so large that the EIT-AT splitting interval Δ f m exceeds the absorption peak width of the cold atom while scanning the frequency of the probe laser (ω p ). Moreover, EIT-AT splitting can be observed if Δ f m exceeds the natural linewidth Γ eg of the intermediate states while scanning the coupling laser (ω c ) and maintains a high spectral resolution with a high signal-to-noise ratio. While scanning ω c , the upper microwave electric field intensity is limited by the scanning range of our setup. Using our system, we measure the maximum field to be 21.6 mV cm−1, nearly three times higher than that of 6.8 mV cm−1 while scanning ω p . The results indicate that the linear range of E MW measured using EIT-AT splitting considerably improves in cold Rydberg atoms.

Journal of Physics B Atomic Molecular and Optical Physics•Dec 23, 2022•31 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Span shift and extension of quantum microwave electrometry with Rydberg atoms dressed by an auxiliary microwave field

Feng-Dong Jia, Xiubin Liu, Jiong Mei +7 more

The Rydberg electromagnetically induced transparency (EIT)--Autler Townes (AT) splitting proportional to the target microwave electric field strength is an atom-based primary traceable standard in microwave electrometry. The minimum detected microwave electric field is limited when the EIT-AT splitting is indistinguishable. We design a method for auxiliary microwave-dressed Rydberg atoms that extends the electrometric span. We theoretically and experimentally show that the low bound of the direct SI-traceable microwave electric field is extended by two orders of magnitude, which is from several mV/cm to $\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ in a room-temperate Rb cell with a modest setup.

Physical Review A•Jun 24, 2021•70 citations

Using amplitude modulation of the microwave field to improve the sensitivity of Rydberg-atom based microwave electrometry

Xiubin Liu, Feng-Dong Jia, Huaiyu Zhang +6 more

The microwave (MW) field can be measured by the Autler–Townes (AT) splitting of the electromagnetically induced transparency (EIT) spectrum in the Rydberg atomic system; however, the EIT-AT splitting method fails in weak MW fields. We used the amplitude modulation of the MW field to resolve the EIT-AT splitting in weak MW fields. The EIT-AT splitting interval can be directly obtained, and the minimum detectable MW strength is improved by six times compared with the traditional EIT-AT splitting method. The proposed method is more intuitive and convenient for measuring the strength of weak MW fields in practical applications.

AIP Advances•Aug 1, 2021•45 citations

Microwave Electrometry with Rydberg Eletromagnetically Induced Transparency in Vapor Cells

Haoquan Fan

An atom-based approach is presented to detect absolute microwave (MW) electric fields (E-fields). The approach uses Rydberg atoms in vapor cells at room temperature. The MW E-field measurements utilize a bright resonance prepared within an electromagnetically induced transparency (EIT) window. The large transition dipole moments between energetically adjacent Rydberg states enable this method to make traceable E-field measurements with a sensitivity that is several orders of magnitude higher than the current standard for MW E-field measurements. The method can be used to image MW E-field in the near field regime with a subwavelength resolution of $\\mathrm{\\lambda_{MW}/650}$, where $\\mathrm{\\lambda_{MW}}$ is the wavelength of the MW E-field. A high accuracy of $\\mathrm{1\\%}$ has been reached by minimizing the effects of the vapor cell geometry on the measured MW E-field. The dissertation also presents an alternative technique to perform the MW E-field measurement using dispersive properties of the EIT spectrum with a prism vapor cell. Recently, we applied a homodyne detection technique with a Mach Zehnder interferometer to achieve a new sensitivity limit for the MW E-field measurement, $\\mathrm{\\sim3~\\mu Vcm^{-1}Hz^{-1/2}}$. The new sensitivity is one order of magnitude better than our prior best sensitivity presented in Ref. [Nat. Phys. 8, 819 (2012)]. The Rydberg atom-based method is promising to be a new standard for MW E-field measurements and to develop into portable devices in the field of MW technologies.

•Jul 20, 2016•0 citations
Abstract In this study, we investigated Rydberg atom-based microwave (MW) electrometry using polarization spectroscopy in a room-temperature vapor cell. By measuring Autler-Townes splitting in the electromagnetically induced transparency (EIT) spectrum, we determined that the minimum measurable MW electric field is approximately five times lower than conventional EIT techniques. The results are well reproduced by a full optical Bloch equation model, which takes into account all the hyperfine levels involved. Subsequently, the EIT setup was used to characterize a custom MW cylindrical lens, which increases the field at the focus by a factor of three, decreasing the minimum measurable MW electric field by the same amount. Our results indicate that the combination of polarization spectroscopy and a MW lens may enhance MW electrometry, and may allow its use as a secondary standard.
We have theoretically and experimentally studied the dispersive signal of the Rydberg atomic electromagnetically-induced transparency (EIT) Autler–Townes (AT) splitting spectra obtained using amplitude modulation of the microwave (MW) electric field. In addition to the two zero-crossing points interval Δf zeros, the dispersion signal has two positive maxima with an interval defined as the shoulder interval Δf sho, which is theoretically expected to be used to measure a much weaker MW electric field. The relationship of the MW field strength E MW and Δf sho is experimentally studied at the MW frequencies of 31.6 GHz and 9.2 GHz respectively. The results show that Δf sho can be used to characterize the much weaker E MW than that of Δf zeros and the traditional EIT–AT splitting interval Δf m; the minimum E MW measured by Δf sho is about 30 times smaller than that by Δf m. As an example, the minimum E MW at 9.2 GHz that can be characterized by Δf sho is 0.056 mV/cm, which is the minimum value characterized by the frequency interval using a vapor cell without adding any auxiliary fields. The proposed method can improve the weak limit and sensitivity of E MW measured by the spectral frequency interval, which is important in the direct measurement of weak E MW.
Abstract We theoretically and experimentally studied quantum microwave electrometry in a cold atomic system using Rydberg electromagnetic induction transparency (EIT) and Autler–Townes splitting (EIT-AT splitting). In cold atoms, a spectral linewidth of ∼500 kHz for EIT was achieved owing to a significant reduction in residual Doppler width, i.e. by at least an order of magnitude, compared to that in vapor cells at room temperature. Therefore, the minimum microwave electric field intensity (E MW) that can be measured is 430 µV cm−1, which is one order higher sensitivity in the EIT-AT regime than that in vapor cells at room temperature. Unlike microwave electrometry in atomic vapor cells, EIT-AT splitting cannot be observed if E MW is so large that the EIT-AT splitting interval Δ f m exceeds the absorption peak width of the cold atom while scanning the frequency of the probe laser (ω p ). Moreover, EIT-AT splitting can be observed if Δ f m exceeds the natural linewidth Γ eg of the intermediate states while scanning the coupling laser (ω c ) and maintains a high spectral resolution with a high signal-to-noise ratio. While scanning ω c , the upper microwave electric field intensity is limited by the scanning range of our setup. Using our system, we measure the maximum field to be 21.6 mV cm−1, nearly three times higher than that of 6.8 mV cm−1 while scanning ω p . The results indicate that the linear range of E MW measured using EIT-AT splitting considerably improves in cold Rydberg atoms.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
The Rydberg electromagnetically induced transparency (EIT)--Autler Townes (AT) splitting proportional to the target microwave electric field strength is an atom-based primary traceable standard in microwave electrometry. The minimum detected microwave electric field is limited when the EIT-AT splitting is indistinguishable. We design a method for auxiliary microwave-dressed Rydberg atoms that extends the electrometric span. We theoretically and experimentally show that the low bound of the direct SI-traceable microwave electric field is extended by two orders of magnitude, which is from several mV/cm to $\ensuremath{\mu}\mathrm{V}/\mathrm{cm}$ in a room-temperate Rb cell with a modest setup.
The microwave (MW) field can be measured by the Autler–Townes (AT) splitting of the electromagnetically induced transparency (EIT) spectrum in the Rydberg atomic system; however, the EIT-AT splitting method fails in weak MW fields. We used the amplitude modulation of the MW field to resolve the EIT-AT splitting in weak MW fields. The EIT-AT splitting interval can be directly obtained, and the minimum detectable MW strength is improved by six times compared with the traditional EIT-AT splitting method. The proposed method is more intuitive and convenient for measuring the strength of weak MW fields in practical applications.
An atom-based approach is presented to detect absolute microwave (MW) electric fields (E-fields). The approach uses Rydberg atoms in vapor cells at room temperature. The MW E-field measurements utilize a bright resonance prepared within an electromagnetically induced transparency (EIT) window. The large transition dipole moments between energetically adjacent Rydberg states enable this method to make traceable E-field measurements with a sensitivity that is several orders of magnitude higher than the current standard for MW E-field measurements. The method can be used to image MW E-field in the near field regime with a subwavelength resolution of mathrmlambdaMW/650\\mathrm{\\lambda_{MW}/650}mathrmlambdaMW​/650, where mathrmlambdaMW\\mathrm{\\lambda_{MW}}mathrmlambdaMW​ is the wavelength of the MW E-field. A high accuracy of $\\mathrm{1\\%}$ has been reached by minimizing the effects of the vapor cell geometry on the measured MW E-field. The dissertation also presents an alternative technique to perform the MW E-field measurement using dispersive properties of the EIT spectrum with a prism vapor cell. Recently, we applied a homodyne detection technique with a Mach Zehnder interferometer to achieve a new sensitivity limit for the MW E-field measurement, mathrmsim3 muVcm−1Hz−1/2\\mathrm{\\sim3~\\mu Vcm^{-1}Hz^{-1/2}}mathrmsim3 muVcm−1Hz−1/2. The new sensitivity is one order of magnitude better than our prior best sensitivity presented in Ref. [Nat. Phys. 8, 819 (2012)]. The Rydberg atom-based method is promising to be a new standard for MW E-field measurements and to develop into portable devices in the field of MW technologies.