Measurement is an essential component of quantum algorithms, and for superconducting qubits it is often the most error prone. Here, we demonstrate model-based readout optimization achieving low measurement errors while avoiding detrimental side effects. For simultaneous and midcircuit measurements across 17 qubits, we observe 1.5% error per qubit with a 500 ns end-to-end duration and minimal excess reset error from residual resonator photons. We also suppress measurement-induced state transitions achieving a leakage rate limited by natural heating. This technique can scale to hundreds of qubits and be used to enhance the performance of error-correcting codes and near-term applications.
Readout errors in superconducting qubits include incorrect state assignment, bit flips within the computational subspace, and leakage to non-computational states. These errors require different mitigation strategies, yet conventional measurement fidelity and repeatability metrics do not resolve their individual contributions. Previous repeated-readout studies have shown that temporal correlations reveal additional information about readout errors. Here we introduce the Readout Error Decoder (RED), which converts repeated thresholded binary records into a channel-resolved error budget. Controlled error injections validate the channel-specific response of the decoder. We demonstrate RED on both fluxonium and transmon qubits and across distinct leakage-lifetime regimes. RED identifies the error channels limiting readout performance without requiring dedicated discrimination of non-computational states, providing a basis for targeted readout optimization across different qubit modalities.
Fast, accurate, and low-leakage qubit measurement is a key requirement for quantum error correction. Here, we demonstrate measurement of a superconducting transmon qubit with a total duration of 97(1) ns, defined as the time from the start of the measurement pulse until the measurement-induced error on a subsequent
π-pulse operation falls below
10−4. By combining a large state-averaged resonator decay rate of
κeff/2π = 30.8 MHz with a dispersive shift close to the optimal SNR-per-photon condition, we achieve an assignment error of 0.17(1)% using a 58-ns measurement pulse, with residual readout photons depleting passively in tens of nanoseconds without an active depletion pulse. Using a repeated-measurement sequence together with a leakage-sensitive measurement, we benchmark the measurement-induced state transitions, finding a per-measurement leakage rate of
2.7(2)×10−5, only twice the background rate and two orders of magnitude below the measurement-induced relaxation rate, which dominates the assignment error. Floquet simulations indicate that the multiphoton resonances present at the operating point are weakly coupled and traversed diabatically, without causing leakage. These results demonstrate that a large resonator decay rate, combined with a dispersive shift close to the optimal SNR-per-photon condition, can enable fast, high-fidelity, low-leakage dispersive readout at small qubit-resonator detuning.
Leakage errors are unwanted transfer of population outside of a defined computational subspace and they occur in almost every platform for quantum computing. While prevalent, leakage is often overlooked when measuring and reporting the fidelity of quantum gates with standard methods. In fact, when leakage is substantial it can cause a large overestimation of fidelity from the typical method used to measure fidelity, randomized benchmarking. We provide several methods for properly estimating fidelity in the presence of leakage errors that are applicable in different error regimes with carefully chosen sequence lengths. Then, we numerically demonstrate the methods for two-qubit randomized benchmarking, which often have the largest errors. Finally, we reanalyze previously shared data from Quantinuum systems with some of the methods provided.
In superconducting circuits, drive-induced unwanted transitions limit the readout power, thereby constraining readout speed and fidelity. When such transitions excite the qubit into leakage states, they produce correlated errors that are particularly harmful for quantum error correction. Native nonlinear qubit-readout resonator coupling is a promising alternative to conventional linear hybridization because it provides intrinsic Purcell protection and stricter selection rules for multiphoton processes. In realistic devices, however, we show that such a coupling alone neither eliminates nor necessarily suppresses drive-induced transitions. Instead, if not appropriately engineered, these couplings often worsen the situation by introducing additional parasitic processes. Moreover, the rates of these unwanted transitions remain sensitive to the choice of readout frequency, regardless of the coupling mechanism. We demonstrate that readout-induced leakage can thus vary by orders of magnitude even when readout frequencies differ by less than ~7%. Our results establish that the benefits of native nonlinear couplings are realized only through informed device design, including the spectral placement of relevant auxiliary modes and elimination of parasitic ones.
Leakage errors occur when a quantum system leaves the two-level qubit subspace. Reducing these errors is critically important for quantum error correction to be viable. To quantify leakage errors, we use randomized benchmarking in conjunction with measurement of the leakage population. We characterize single qubit gates in a superconducting qubit, and by refining our use of derivative reduction by adiabatic gate pulse shaping along with detuning of the pulses, we obtain gate errors consistently below 10^{-3} and leakage rates at the 10^{-5} level. With the control optimized, we find that a significant portion of the remaining leakage is due to incoherent heating of the qubit.