Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2305.14184 · Applied Physics Letters

High-temperature superconductor quantum flux parametron for energy efficient logic

Han Cai, Jay C. LeFebvre, Hao Li, Ethan Y. Cho, Nobuyuki Yoshikawa, Shane A. Cybart

Published May 20, 2024• 8 citations
arXivHTMLPDF

Abstract

We report the fabrication and measurement of quantum flux parametron logic from high-transition-temperature Josephson junctions operating at 25 K, above the temperature of liquid helium. The circuits are written directly into the plane of a single-layer thin film of YBa2Cu3O7 using a focused helium ion beam. A single-cell quantum flux parametron was constructed and correct logic operation was verified by using an on-chip superconducting quantum interference device for readout. A three-cell shift register was also fabricated and tested using a three-phase clock cycle. We estimate the average bit energy to be about 1×10−20 J at 1 GHz.

DOI
10.1063/5.0206445

Related papers

YBa$_{2}$Cu$_{3}$O$_{7-\delta }$Single Flux Quantum Flip Flop Directly Written With a Focused Helium Ion Beam

Han Cai, Hao Li, Ethan Y. Cho +2 more

Superconducting logic circuits based on low transition temperature (Tc) are attractive due to their intrinsic low power consumption and high operating frequency. They have a wide variety of applications (particularly in future computing), but are difficult to use because they require cooling with liquid helium to operate. The current high Tclogic circuit based on YBa2Cu3O7-δ(YBCO) already has the ability to operate at a temperature above 4 K. However, this material is difficult to integrate into large-scale circuits by the traditional YBCO junction fabrication process. The limits of fabrication methods are the bottleneck stifling this material's potential for integration into logic circuits. As such, in this paper we aim to advance the state of the art in junction fabrication technology. Here we report the demonstration of a high Tcsuperconducting single flux quantum (SFQ) circuit made by a focused helium ion beam that is easily fabricated and can readily be incorporated into a large-scale integration with nano-scale junctions for future applications. An inductively coupled readout superconducting quantum interference device (SQUID) is employed to reduce the circuit complexity. The circuit parameters and performance are discussed.

IEEE Transactions on Applied Superconductivity•Apr 1, 2021•15 citations

Design and fabrication of QFP logic gates based on YBa/sub 2/Cu/sub 3/O/sub 7/ step-edge junctions

H. Hasegawa, Y. Tarutani, Uki Kabasawa +3 more

Quantum Flux Parametron (QFP) logic gates were designed and fabricated from a single layer of YBa/sub 2/Cu/sub 3/O/sub 7/ thin film based on step-edge Josephson junctions. Self-inductance (L) of the QFP loop, an important circuit parameter, as is critical current (J/sub c/) of the Josephson junction, was determined by using directly coupled dc superconducting quantum interference devices (SQUIDs). Magnetically coupled dc SQUIDs were used to detect the output signal from the QFP. Simulated waveforms were used to identify the operation modes of the QFP as a function of the circuit parameters. From examination of the output waveforms of the QFP, operation in agreement with simulations was confirmed.

IEEE Transactions on Applied Superconductivity•Jun 1, 1997•4 citations

All-high-T c superconductor rapid-single-flux-quantum circuit operating at ∼30 K

S.L. Shokhor, Boris E. Nadgorny, Michael Gurvitch +5 more

We have implemented a simple circuit of the rapid single-flux-quantum (RSFQ) logic family using a single-layer YBa2Cu3O7−x thin-film structure with 14 in-plane Josephson junctions formed by direct electron beam writing. The circuit includes two dc/SFQ converters, two Josephson transmission lines, a complete RS SFQ flip-flop, and an SFQ/dc converter (readout SQUID). Low-frequency testing has shown that the dc-current-biased circuit operates correctly and reliably at T∼30 K, a few degrees below the effective critical temperature of the junctions. Prospects for a further increase of the operation temperature and implementation of more complex RSFQ circuits are discussed in brief.

Applied Physics Letters•Nov 6, 1995•59 citations

abrication of QFP Logic Gates Based on YBa2Cu3O7 Step-Edge Junctions

H. Hasegawa, Yoshinobu Tarutani, Uki Kabasawa +3 more

Abstruct-Quantum Flux Parametron (QFP) logic gates were designed and fabricated from a single layer of YJ3a2Cu307 thin film based on step-edge Josephson junctions. Self-inductance (L) of the QFP loop, an important circuit parameter, as is critical current (I,) of the Josephson junction, was determined by using directly coupled dc superconducting quantum interference devices (SQUIDS). Magnetically coupled dc SQUIDs were used to detect the output signal from the QFP. Simulated waveforms were used to identify the operation modes of the QFP as a function of the circuit parameters. From examination of the output waveforms of the QFP, operation in agreement with simulations was confirmed.

•Jan 1, 1997•0 citations

A 3 bit single flux quantum shift register based on high-Tc bicrystal Josephson junctions operating at 50 K

B. Oelze, B. Ruck, Erik Sodtke +3 more

A 3 bit single flux quantum (SFQ) shift register based on high-Tc bicrystal Josephson junctions has been designed, fabricated, and experimentally tested. The circuit consists of 26 bicrystal Josephson junctions and includes the shift register itself, two dc-SFQ converters, one readout superconducting quantum interference device, serving as a SFQ-dc converter, and three Josephson transmission lines. The correct operation of all circuit components has been demonstrated by low frequency testing at a temperature of 50 K.

Applied Physics Letters•Feb 3, 1997•22 citations

Measurement of the error rate of single flux quantum circuits with high temperature superconductors

Ben J. Ruck, Yonuk Chong, Regina Dittmann +6 more

The determination of bit error rates in single flux quantum logic circuits operating at temperatures well above the temperature of liquid helium is essential since the question of stability against thermal noise arises. We determined experimentally the static and for the first time the dynamic error rate at temperatures of about 40 K with the help of simple test circuits. The static error rate has been investigated using two different circuits with bicrystal junctions in either single-layer or multilayer configuration. In both cases the internal state of a storage loop was observed by a dc-SQUID. A ring oscillator based on a Josephson transmission line allowed us to measure the dynamic error rate of a Josephson comparator at high frequencies. This circuit has been fabricated using junctions by focused-electron-beam irradiation. It is specially suited for the detection of seldom occurring switching errors.

IEEE Transactions on Applied Superconductivity•Jun 1, 1999•15 citations
We report the fabrication and measurement of quantum flux parametron logic from high-transition-temperature Josephson junctions operating at 25 K, above the temperature of liquid helium. The circuits are written directly into the plane of a single-layer thin film of YBa2Cu3O7 using a focused helium ion beam. A single-cell quantum flux parametron was constructed and correct logic operation was verified by using an on-chip superconducting quantum interference device for readout. A three-cell shift register was also fabricated and tested using a three-phase clock cycle. We estimate the average bit energy to be about 1×10−20 J at 1 GHz.
YBa2_{2}2​Cu3_{3}3​O7−δ_{7-\delta }7−δ​Single Flux Quantum Flip Flop Directly Written With a Focused Helium Ion Beam
Superconducting logic circuits based on low transition temperature (Tc) are attractive due to their intrinsic low power consumption and high operating frequency. They have a wide variety of applications (particularly in future computing), but are difficult to use because they require cooling with liquid helium to operate. The current high Tclogic circuit based on YBa2Cu3O7-δ(YBCO) already has the ability to operate at a temperature above 4 K. However, this material is difficult to integrate into large-scale circuits by the traditional YBCO junction fabrication process. The limits of fabrication methods are the bottleneck stifling this material's potential for integration into logic circuits. As such, in this paper we aim to advance the state of the art in junction fabrication technology. Here we report the demonstration of a high Tcsuperconducting single flux quantum (SFQ) circuit made by a focused helium ion beam that is easily fabricated and can readily be incorporated into a large-scale integration with nano-scale junctions for future applications. An inductively coupled readout superconducting quantum interference device (SQUID) is employed to reduce the circuit complexity. The circuit parameters and performance are discussed.
Quantum Flux Parametron (QFP) logic gates were designed and fabricated from a single layer of YBa/sub 2/Cu/sub 3/O/sub 7/ thin film based on step-edge Josephson junctions. Self-inductance (L) of the QFP loop, an important circuit parameter, as is critical current (J/sub c/) of the Josephson junction, was determined by using directly coupled dc superconducting quantum interference devices (SQUIDs). Magnetically coupled dc SQUIDs were used to detect the output signal from the QFP. Simulated waveforms were used to identify the operation modes of the QFP as a function of the circuit parameters. From examination of the output waveforms of the QFP, operation in agreement with simulations was confirmed.
We have implemented a simple circuit of the rapid single-flux-quantum (RSFQ) logic family using a single-layer YBa2Cu3O7−x thin-film structure with 14 in-plane Josephson junctions formed by direct electron beam writing. The circuit includes two dc/SFQ converters, two Josephson transmission lines, a complete RS SFQ flip-flop, and an SFQ/dc converter (readout SQUID). Low-frequency testing has shown that the dc-current-biased circuit operates correctly and reliably at T∼30 K, a few degrees below the effective critical temperature of the junctions. Prospects for a further increase of the operation temperature and implementation of more complex RSFQ circuits are discussed in brief.
Abstruct-Quantum Flux Parametron (QFP) logic gates were designed and fabricated from a single layer of YJ3a2Cu307 thin film based on step-edge Josephson junctions. Self-inductance (L) of the QFP loop, an important circuit parameter, as is critical current (I,) of the Josephson junction, was determined by using directly coupled dc superconducting quantum interference devices (SQUIDS). Magnetically coupled dc SQUIDs were used to detect the output signal from the QFP. Simulated waveforms were used to identify the operation modes of the QFP as a function of the circuit parameters. From examination of the output waveforms of the QFP, operation in agreement with simulations was confirmed.
A 3 bit single flux quantum (SFQ) shift register based on high-Tc bicrystal Josephson junctions has been designed, fabricated, and experimentally tested. The circuit consists of 26 bicrystal Josephson junctions and includes the shift register itself, two dc-SFQ converters, one readout superconducting quantum interference device, serving as a SFQ-dc converter, and three Josephson transmission lines. The correct operation of all circuit components has been demonstrated by low frequency testing at a temperature of 50 K.
The determination of bit error rates in single flux quantum logic circuits operating at temperatures well above the temperature of liquid helium is essential since the question of stability against thermal noise arises. We determined experimentally the static and for the first time the dynamic error rate at temperatures of about 40 K with the help of simple test circuits. The static error rate has been investigated using two different circuits with bicrystal junctions in either single-layer or multilayer configuration. In both cases the internal state of a storage loop was observed by a dc-SQUID. A ring oscillator based on a Josephson transmission line allowed us to measure the dynamic error rate of a Josephson comparator at high frequencies. This circuit has been fabricated using junctions by focused-electron-beam irradiation. It is specially suited for the detection of seldom occurring switching errors.