Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2303.13928 · Physical Review Applied

Nonlocal Superconducting Single-Photon Detector

Federico Paolucci

Published Jul 5, 2023• 5 citations
arXivHTMLPDF

Abstract

We present and theoretically analyze the performance of a nonlocal superconducting single-photon detector. The device operates due to the energy-to-phase conversion mechanism, where the energy of the absorbed single photon is transformed in a variation of the superconducting phase. Within this scope, the detector is designed in the form of a double-loop superconductor--normal-metal--superconductor ($S$-$N$-$S$) Josephson interferometer, where the detection occurs in a long $S$-$N$-$S$ junction and the readout is operated by a short $S$-$N$-$S$ junction. The variation of the superconducting phase across the readout junction is measured by recording the quasiparticle current flowing through a tunnel-coupled superconducting probe. By exploiting realistic geometry and materials, the detector is able to reveal single photons of frequency down to 10 GHz when operated at 10 mK. Furthermore, the device provides a value of the signal-to-noise ratio of up ${10}^{4}$ in the range from 10 GHz to 10 THz by selection of the magnetic flux and the bias voltage. This device will hopefully find direct application as a single-photon detector in both basic science and quantum technology, while the energy-to-phase conversion mechanism could be the basis of nonlocal readout and memory architectures for superconducting qubits.

DOI
10.1103/physrevapplied.20.014003

Related papers

A highly sensitive broadband superconducting thermoelectric single-photon detector

Federico Paolucci, Gaia Germanese, Alessandro Braggio +1 more

We propose a passive single-photon detector based on the bipolar thermoelectric effect occurring in tunnel junctions between two different superconductors thanks to spontaneous electron–hole symmetry breaking. Our superconducting thermoelectric detector (STED) converts a finite temperature difference caused by the absorption of a single photon into an open circuit thermovoltage. Designed with feasible parameters, our STED is able to reveal single photons of frequency ranging from ∼15 GHz to ∼150 PHz depending on the chosen design and materials. In particular, this detector is expected to show values of the signal-to-noise ratio SNR∼15 at ν = 50 GHz when operated at a temperature of 10 mK. Interestingly, this device can be viewed as a digital single-photon detector, since it generates an almost constant voltage VS for the full operation energies. Our STED can reveal single photons in a frequency range wider than four decades with the possibility to discern the energy of the incident photon by measuring the time persistence of the generated thermovoltage. Its broadband operation suggests that our STED could find practical applications in several fields of quantum science and technology, such as quantum computing, telecommunications, optoelectronics, THz spectroscopy, and astro-particle physics.

arXiv:2302.02933•Applied Physics Letters•Apr 24, 2023•19 citations

Josephson junction infrared single-photon detector

Evan D. Walsh, Woochan Jung, Gil-Ho Lee +9 more

Josephson junctions are superconducting devices used as high-sensitivity magnetometers and voltage amplifiers as well as the basis of high-performance cryogenic computers and superconducting quantum computers. Although device performance can be degraded by the generation of quasiparticles formed from broken Cooper pairs, this phenomenon also opens opportunities to sensitively detect electromagnetic radiation. We demonstrate single near-infrared photon detection by coupling photons to the localized surface plasmons of a graphene-based Josephson junction. Using the photon-induced switching statistics of the current-biased device, we reveal the critical role of quasiparticles generated by the absorbed photon in the detection mechanism. The photon sensitivity will enable a high-speed, low-power optical interconnect for future superconducting computing architectures.

arXiv:2011.02624•Science•Apr 22, 2021•106 citations

Proximity SQUID Single-Photon Detector via Temperature-to-Voltage Conversion

Paolo Solinas, Francesco Giazotto, Giovanni Piero Pepe

The authors discuss the possible implementation of a single-photon detector based on a superconducting quantum interference device, or SQUID. The SQUID is initialized in an unstable state through the magnetic flux piercing it. A photon absorbed in a proximized normal-metal link induces a change in the critical current of the link, and a voltage pulse at the extremes of the device. Pulses of several tens of microvolts could result. Such a device allows the discrimination of a vast range of photon frequencies and is robust against thermal noise, making it a valuable candidate for detecting terahertz photons in particular.

arXiv:1711.10846•Physical Review Applied•Aug 13, 2018•15 citations

Quantum Microwave Photodetection Using Superconducting Josephson Circuits.

Brendan Osberg

Superconducting circuits have recently become a major contender for the implementation of quantum computers owing to their compatibility with existing microchip fabrication technologies. Their utility stems largely from their ability to be coupled with resonant cavities for the purposes of trapping and relaying microwave radiation. Because of this feature, scientists are able to transmit quantum information from a variety of qubits. Though quantum-limited amplifiers exist, unfortunately there currently exists no microwave photon counter capable of single shot quantum detection. Hence, we use superconducting circuits with Josephson junctions to design a microwave photon detector based on a modified phase qubit that exhibits a bandwidth of 4GHz, and a detection fidelity of 98%. We use metastable barrier transition (driven by incident photons) to create an avalanche effect analogous to current photo-diodes. Linear coupling of the junction flux with the radiation permits photodetection from an arbitrary quantum source in the GHz range. We show the device to be robust to changes in drive frequency, temporal photon width, and resonator quality factor, and we optimize our device with respect to these parameters. We show the device to be stable over the necessary time scales, and yet sensitive enough to accurately measure photons on demand.

•Sep 3, 2009•0 citations

Stepping Closer to Pulsed Single Microwave Photon Detectors for Axions Search

Alessandro D’Elia, A. Rettaroli, S. Tocci +23 more

Axions detection requires the ultimate sensitivity down to the single-photon limit. In the microwave region, this corresponds to energies in the yJ range. This extreme sensitivity has to be combined with an extremely low dark-count rate since the probability of axions conversion into microwave photons is supposed to be very low. To face this complicated task, we followed two promising approaches that both rely on the use of superconducting devices based on the Josephson effect. The first one is to use a single Josephson junction (JJ) as a switching detector (i.e., exploiting the superconducting to normal state transition in the presence of microwave photons). We designed a device composed of a coplanar waveguide terminated on a current-biased JJ. We tested its efficiency to pulsed (pulse duration 10 ns) microwave signals since this configuration is closer to an actual axions search experiment. We show how our device is able to reach detection capability of the order of ten photons with the frequency of 8 GHz. The second approach is based on an intrinsically quantum device formed by two resonators coupled only via a superconducting qubit network. This approach relies on quantum nondemolition measurements of the resonator photons. We show that by injecting radiofrequency power into the resonator, the frequency position of the resonant drop in the transmission coefficient (S21) can be modulated up to 4 MHz. We anticipate that, once optimized, both the devices have the potential to reach single-photon sensitivity.

arXiv:2302.07556•IEEE Transactions on Applied Superconductivity•Nov 4, 2022•20 citations

Applications of superconducting electronics to quantum optics and quantum metrology

Ling Yun Hao

SQUIDs (superconducting quantum interference devices) have been in use for more than half a century and constitute one of the first macroscopic quantum devices. SQUIDs operating at millikelvin temperatures can act as qubits for quantum computers and the recent reports of more than 50 qubit circuits indicate how far the technology has developed. In this talk, the author will describe two other applications of SQUIDs as quantum detectors, focusing on single spin and single photon energy resolving detection. Most superconducting devices rely on tri-layer Josephson tunnel junctions which are not easily scalable to the nanoscale. We have developed a Josephson junction fabrication method, based on electron beam lithography or focused ion beam milling of a single thin film of superconductor (Nb generally) which can provide sizes down to 50 nm. These devices are particularly relevant for two main applications in quantum technology and metrology. First, by shrinking the size of the SQUID loop and the junctions to around 200 nm, the sensitivity of the SQUID for magnetization measurements is improved to the level where a single electron spin flip may be detected. This is possible at the relatively elevated temperature of 4K.  We are working with Surrey University to implant single magnetic ions within the SQUID loop to provide a platform to test this combination as the basis for a new form of qubit operating at higher temperatures than the conventional Transmon superconducting devices. A second SQUID based detector which we are developing is an inductive transition edge sensor device (ISTED) for energy resolving measurements of single photons. This is based on the development of conventional transition edge sensors where we detect the change of the penetration depth of a small thin film of superconductor when it absorbs a photon. In this way, a major source of noise in conventional TES may be avoided since the absorber remains in the superconducting state at all times. In this way we have demonstrated single photon detection at 633 nm with 0.1eV resolution at operating temperature of 7.5K.

Advances in Automobile Engineering•Jan 1, 2021•0 citations
We present and theoretically analyze the performance of a nonlocal superconducting single-photon detector. The device operates due to the energy-to-phase conversion mechanism, where the energy of the absorbed single photon is transformed in a variation of the superconducting phase. Within this scope, the detector is designed in the form of a double-loop superconductor--normal-metal--superconductor (SSS-NNN-SSS) Josephson interferometer, where the detection occurs in a long SSS-NNN-SSS junction and the readout is operated by a short SSS-NNN-SSS junction. The variation of the superconducting phase across the readout junction is measured by recording the quasiparticle current flowing through a tunnel-coupled superconducting probe. By exploiting realistic geometry and materials, the detector is able to reveal single photons of frequency down to 10 GHz when operated at 10 mK. Furthermore, the device provides a value of the signal-to-noise ratio of up 104{10}^{4}104 in the range from 10 GHz to 10 THz by selection of the magnetic flux and the bias voltage. This device will hopefully find direct application as a single-photon detector in both basic science and quantum technology, while the energy-to-phase conversion mechanism could be the basis of nonlocal readout and memory architectures for superconducting qubits.
We propose a passive single-photon detector based on the bipolar thermoelectric effect occurring in tunnel junctions between two different superconductors thanks to spontaneous electron–hole symmetry breaking. Our superconducting thermoelectric detector (STED) converts a finite temperature difference caused by the absorption of a single photon into an open circuit thermovoltage. Designed with feasible parameters, our STED is able to reveal single photons of frequency ranging from ∼15 GHz to ∼150 PHz depending on the chosen design and materials. In particular, this detector is expected to show values of the signal-to-noise ratio SNR∼15 at ν = 50 GHz when operated at a temperature of 10 mK. Interestingly, this device can be viewed as a digital single-photon detector, since it generates an almost constant voltage VS for the full operation energies. Our STED can reveal single photons in a frequency range wider than four decades with the possibility to discern the energy of the incident photon by measuring the time persistence of the generated thermovoltage. Its broadband operation suggests that our STED could find practical applications in several fields of quantum science and technology, such as quantum computing, telecommunications, optoelectronics, THz spectroscopy, and astro-particle physics.
Josephson junctions are superconducting devices used as high-sensitivity magnetometers and voltage amplifiers as well as the basis of high-performance cryogenic computers and superconducting quantum computers. Although device performance can be degraded by the generation of quasiparticles formed from broken Cooper pairs, this phenomenon also opens opportunities to sensitively detect electromagnetic radiation. We demonstrate single near-infrared photon detection by coupling photons to the localized surface plasmons of a graphene-based Josephson junction. Using the photon-induced switching statistics of the current-biased device, we reveal the critical role of quasiparticles generated by the absorbed photon in the detection mechanism. The photon sensitivity will enable a high-speed, low-power optical interconnect for future superconducting computing architectures.
The authors discuss the possible implementation of a single-photon detector based on a superconducting quantum interference device, or SQUID. The SQUID is initialized in an unstable state through the magnetic flux piercing it. A photon absorbed in a proximized normal-metal link induces a change in the critical current of the link, and a voltage pulse at the extremes of the device. Pulses of several tens of microvolts could result. Such a device allows the discrimination of a vast range of photon frequencies and is robust against thermal noise, making it a valuable candidate for detecting terahertz photons in particular.
Superconducting circuits have recently become a major contender for the implementation of quantum computers owing to their compatibility with existing microchip fabrication technologies. Their utility stems largely from their ability to be coupled with resonant cavities for the purposes of trapping and relaying microwave radiation. Because of this feature, scientists are able to transmit quantum information from a variety of qubits. Though quantum-limited amplifiers exist, unfortunately there currently exists no microwave photon counter capable of single shot quantum detection. Hence, we use superconducting circuits with Josephson junctions to design a microwave photon detector based on a modified phase qubit that exhibits a bandwidth of 4GHz, and a detection fidelity of 98%. We use metastable barrier transition (driven by incident photons) to create an avalanche effect analogous to current photo-diodes. Linear coupling of the junction flux with the radiation permits photodetection from an arbitrary quantum source in the GHz range. We show the device to be robust to changes in drive frequency, temporal photon width, and resonator quality factor, and we optimize our device with respect to these parameters. We show the device to be stable over the necessary time scales, and yet sensitive enough to accurately measure photons on demand.
Axions detection requires the ultimate sensitivity down to the single-photon limit. In the microwave region, this corresponds to energies in the yJ range. This extreme sensitivity has to be combined with an extremely low dark-count rate since the probability of axions conversion into microwave photons is supposed to be very low. To face this complicated task, we followed two promising approaches that both rely on the use of superconducting devices based on the Josephson effect. The first one is to use a single Josephson junction (JJ) as a switching detector (i.e., exploiting the superconducting to normal state transition in the presence of microwave photons). We designed a device composed of a coplanar waveguide terminated on a current-biased JJ. We tested its efficiency to pulsed (pulse duration 10 ns) microwave signals since this configuration is closer to an actual axions search experiment. We show how our device is able to reach detection capability of the order of ten photons with the frequency of 8 GHz. The second approach is based on an intrinsically quantum device formed by two resonators coupled only via a superconducting qubit network. This approach relies on quantum nondemolition measurements of the resonator photons. We show that by injecting radiofrequency power into the resonator, the frequency position of the resonant drop in the transmission coefficient (S21) can be modulated up to 4 MHz. We anticipate that, once optimized, both the devices have the potential to reach single-photon sensitivity.
SQUIDs (superconducting quantum interference devices) have been in use for more than half a century and constitute one of the first macroscopic quantum devices. SQUIDs operating at millikelvin temperatures can act as qubits for quantum computers and the recent reports of more than 50 qubit circuits indicate how far the technology has developed. In this talk, the author will describe two other applications of SQUIDs as quantum detectors, focusing on single spin and single photon energy resolving detection. Most superconducting devices rely on tri-layer Josephson tunnel junctions which are not easily scalable to the nanoscale. We have developed a Josephson junction fabrication method, based on electron beam lithography or focused ion beam milling of a single thin film of superconductor (Nb generally) which can provide sizes down to 50 nm. These devices are particularly relevant for two main applications in quantum technology and metrology. First, by shrinking the size of the SQUID loop and the junctions to around 200 nm, the sensitivity of the SQUID for magnetization measurements is improved to the level where a single electron spin flip may be detected. This is possible at the relatively elevated temperature of 4K.  We are working with Surrey University to implant single magnetic ions within the SQUID loop to provide a platform to test this combination as the basis for a new form of qubit operating at higher temperatures than the conventional Transmon superconducting devices. A second SQUID based detector which we are developing is an inductive transition edge sensor device (ISTED) for energy resolving measurements of single photons. This is based on the development of conventional transition edge sensors where we detect the change of the penetration depth of a small thin film of superconductor when it absorbs a photon. In this way, a major source of noise in conventional TES may be avoided since the absorber remains in the superconducting state at all times. In this way we have demonstrated single photon detection at 633 nm with 0.1eV resolution at operating temperature of 7.5K.