Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2209.11052 · Journal of Applied Physics

Numerical analysis of a three-wave-mixing Josephson traveling-wave parametric amplifier with engineered dispersion loadings

Victor Gaydamachenko, Christoph Kissling, R. Dolata, Alexander B Zorin

Published Oct 20, 2022• 23 citations
arXivHTMLPDF

Abstract

The recently proposed Josephson traveling-wave parametric amplifier (JTWPA) based on a ladder transmission line consisting of radio-frequency superconducting quantum interference devices and exploiting three-wave mixing has great potential in achieving both a gain of 20 dB and a flat bandwidth of at least 4 GHz. To realize this concept in practical amplifiers, we model the advanced JTWPA circuit with periodic modulation of the circuit parameters (engineered dispersion loadings), which allow the basic mixing process, i.e., ωs=ωp−ωi, where ωs, ωp, and ωi are the signal, the pump, and the idler frequencies, respectively, and efficiently suppress propagation of unwanted higher tones, including ω2p=2ωp, ωp+s=ωp+ωs, ωp+i=ωp+ωi, etc. The engineered dispersion loadings allow achieving a sufficiently wide 3 dB-bandwidth from 3 to 9 GHz combined with a reasonably small ripple (±2 dB) in the gain-vs-frequency dependence.

DOI
10.1063/5.0111111

Related papers

Quasi-phasematching in a poled Josephson traveling-wave parametric amplifier with three-wave mixing

Alexander B Zorin

We develop the concept of quasi-phasematching (QPM) by implementing it in the recently proposed Josephson traveling-wave parametric amplifier (JTWPA) with three-wave mixing (3WM). The amplifier is based on a ladder transmission line consisting of flux-biased radio frequency superconducting quantum interference devices (SQUIDs) whose nonlinearity is of χ(2)-type. QPM is achieved in the 3WM process, ωp=ωs+ωi (where ωp, ωs, and ωi are the pump, signal, and idler frequencies, respectively) due to designing the JTWPA to include periodically inverted groups of these SQUIDs that reverse the sign of the nonlinearity. Modeling shows that the JTWPA bandwidth is relatively large (∼ 0.4ωp) and flat, while unwanted modes, including ω2p=2ωp, ω+=ωp+ωs, and ω−=2ωp−ωs, are strongly suppressed with the help of engineered dispersion.

arXiv:2101.11697•Applied Physics Letters•May 31, 2021•20 citations

A dispersion-engineered Josephson travelling wave parametric amplifier with periodic impedance perturbation

K Ratter, B-K Tan

We present a new approach to develop a Josephson Junction Travelling Wave Parametric Amplifier (JTWPA) that could potentially minimise the gain-ripple effect. Our design consists of a 50 Ω superconducting niobium coplanar waveguide (CPW) periodically loaded with series of Josephson junctions (JJs) to provide the non-linearity required for wave mixing. The embedded JJs alter the characteristic impedance of the transmission line abruptly, therefore creating the stopbands in the transmission (S21) for the suppression of higher harmonics and provide the means for dispersion engineering required to achieve exponential gain. The simulated gain profile of the amplifier shows that we can obtain a minimum of 15 dB gain from 4–12 GHz, close to a 100% bandwidth performance. More importantly, the characteristic impedance of the main linear transmission line remains unaffected by the strong pump, therefore ensuring the TWPA remains impedance matched to the input and output ports. This can reduce the unwanted gain undulation that inflict the optimal performance of the TWPA.

•Jan 1, 2021•0 citations

Traveling-wave parametric amplifier with three-wave mixing in superconducting transmission line with embedded rf-SQUIDs

Alexander B Zorin

We develop a concept of traveling-wave Josephson parametric amplifier based on a ladder-type superconducting transmission line containing serial array of one-junctions SQUIDs. The circuit operates in a three-wave mixing mode and exploits both quadratic and cubic (Kerr) nonlinearities in the current-phase relation of the SQUIDs controlled by external magnetic flux. These two types of nonlinearities allow efficient three-wave mixing and perfect phase matching, respectively. The transmission line exhibits a power gain with exponential dependence on its length (number of cells $N$) in the widest frequency range, $0 \lesssim f_s, f_i \lesssim f_p$, where $f_s$, $f_i$ and $f_p$ are the signal, idler and pump frequencies, respectively, obeying relation $f_s + f_i = f_p$. Estimation of the amplifier characteristics with typical experimental parameters, number of cells $N$ = 700, length of 28 mm and pump frequency of 12.5 GHz yields a flat (-3 dB) gain of about 20 dB in the bandwidth from 3.35 GHz to 9.15 GHz and a saturation power of -90 dBm.

•Feb 8, 2016•3 citations

Circuit Design and Experimental Characterization of a Josephson Traveling-Wave Parametric Amplifier

Christoph Kissling

Bringing signals from quantum to classical, from few-photon to many-photon levels for further processing, is a common challenge in rising quantum technologies. These include quantum computing, quantum communication, quantum sensing, radio astronomy, and dark matter searches, typically operating at microwave frequencies and millikelvin temperatures. Superconducting parametric amplifiers, as the first piece in the readout chain, have become a cornerstone of these technologies, since they offer unrivaled noise performance near the quantum-mechanical limit and high gain to surpass the noise of subsequent amplifiers. A notable implementation is the Josephson traveling-wave parametric amplifier (TWPA), which stands out due to its bandwidth of several Gigahertz and high saturation power, often larger than -100 dBm. These key properties come at the cost of complexity in design and fabrication: TWPA metamaterials often contain several thousands of Josephson junctions. Designing high-gain TWPAs involves three major challenges: ensuring impedance-matching, phase-matching of parametric amplification, and suppressing unwanted processes, all achievable through sub-wavelength dispersion engineering. This thesis covers the circuit design and analysis, implementation, and experimental characterization of a dispersion-engineered TWPA based on radio-frequency superconducting interference devices (rf-SQUIDs). It focuses on a detailed investigation of dispersion-engineering techniques and their effects on amplifier performance, particularly through the use of time-domain circuit simulations to analyze the multimode dynamics of the circuit. The experimentally realized device features 18 dB of gain, an instantaneous bandwidth spanning from 2.2 to 6.7 GHz, a system noise of 2.5 quanta, and a saturation power of (−86.5 ± 4.0) dBm. With these characteristics, it is suitable for frequency-multiplexed readout of detector arrays or qubits. Its high saturation power, about 10 dB higher than other reported Josephson-junction-based TWPAs, allows increasing the number of qubits per readout line, or decreasing the intermodulation between frequency-multiplexed qubits, both crucial for scaling up quantum computation.

•Feb 24, 2026•0 citations

Three-wave mixing traveling-wave parametric amplifier with periodic variation of the circuit parameters

Anita Fadavi Roudsari, Daryoush Shiri, Hampus Renberg Nilsson +8 more

We report on the implementation of a near-quantum-limited, traveling-wave parametric amplifier that uses three-wave mixing (3WM). To favor amplification by 3WM, we use superconducting nonlinear asymmetric inductive element (SNAIL) loops, biased with a dc magnetic flux. In addition, we equip the device with dispersion engineering features to create a stopband at the second harmonic of the pump and suppress the propagation of the higher harmonics that otherwise degrade the amplification. With a chain of 440 SNAILs, the amplifier provides up to 20 dB gain and a 3-dB bandwidth of 1 GHz. The added noise by the amplifier is found to be less than one photon.

arXiv:2209.07551•Applied Physics Letters•Jan 30, 2023•37 citations

Flux-Driven Josephson Traveling-Wave Parametric Amplifier

Alexander B Zorin

With potentially quantum limited performance and wide frequency bandwidth, traveling-wave Josephson parametric amplifiers (TWJPAs) based on superconducting circuits are in urgent demand for quantum information processing. This study designs a TWJPA in which the interacting pump and signal/idler microwaves propagate with similar phase velocities through two different transmission lines, thereby enabling parametric gain. Such operation is possible due to a chain of SQUIDs that form the signal transmission line, which is magnetically coupled to a separate pump $L\phantom{\rule{0}{0ex}}C$ line. The proposed circuit may greatly simplify the measurement setup and solve the problem of pump depletion.

arXiv:1804.09109•Physical Review Applied•Oct 23, 2019•61 citations
The recently proposed Josephson traveling-wave parametric amplifier (JTWPA) based on a ladder transmission line consisting of radio-frequency superconducting quantum interference devices and exploiting three-wave mixing has great potential in achieving both a gain of 20 dB and a flat bandwidth of at least 4 GHz. To realize this concept in practical amplifiers, we model the advanced JTWPA circuit with periodic modulation of the circuit parameters (engineered dispersion loadings), which allow the basic mixing process, i.e., ωs=ωp−ωi, where ωs, ωp, and ωi are the signal, the pump, and the idler frequencies, respectively, and efficiently suppress propagation of unwanted higher tones, including ω2p=2ωp, ωp+s=ωp+ωs, ωp+i=ωp+ωi, etc. The engineered dispersion loadings allow achieving a sufficiently wide 3 dB-bandwidth from 3 to 9 GHz combined with a reasonably small ripple (±2 dB) in the gain-vs-frequency dependence.
We develop the concept of quasi-phasematching (QPM) by implementing it in the recently proposed Josephson traveling-wave parametric amplifier (JTWPA) with three-wave mixing (3WM). The amplifier is based on a ladder transmission line consisting of flux-biased radio frequency superconducting quantum interference devices (SQUIDs) whose nonlinearity is of χ(2)-type. QPM is achieved in the 3WM process, ωp=ωs+ωi (where ωp, ωs, and ωi are the pump, signal, and idler frequencies, respectively) due to designing the JTWPA to include periodically inverted groups of these SQUIDs that reverse the sign of the nonlinearity. Modeling shows that the JTWPA bandwidth is relatively large (∼ 0.4ωp) and flat, while unwanted modes, including ω2p=2ωp, ω+=ωp+ωs, and ω−=2ωp−ωs, are strongly suppressed with the help of engineered dispersion.
We present a new approach to develop a Josephson Junction Travelling Wave Parametric Amplifier (JTWPA) that could potentially minimise the gain-ripple effect. Our design consists of a 50 Ω superconducting niobium coplanar waveguide (CPW) periodically loaded with series of Josephson junctions (JJs) to provide the non-linearity required for wave mixing. The embedded JJs alter the characteristic impedance of the transmission line abruptly, therefore creating the stopbands in the transmission (S21) for the suppression of higher harmonics and provide the means for dispersion engineering required to achieve exponential gain. The simulated gain profile of the amplifier shows that we can obtain a minimum of 15 dB gain from 4–12 GHz, close to a 100% bandwidth performance. More importantly, the characteristic impedance of the main linear transmission line remains unaffected by the strong pump, therefore ensuring the TWPA remains impedance matched to the input and output ports. This can reduce the unwanted gain undulation that inflict the optimal performance of the TWPA.
We develop a concept of traveling-wave Josephson parametric amplifier based on a ladder-type superconducting transmission line containing serial array of one-junctions SQUIDs. The circuit operates in a three-wave mixing mode and exploits both quadratic and cubic (Kerr) nonlinearities in the current-phase relation of the SQUIDs controlled by external magnetic flux. These two types of nonlinearities allow efficient three-wave mixing and perfect phase matching, respectively. The transmission line exhibits a power gain with exponential dependence on its length (number of cells NNN) in the widest frequency range, 0≲fs,fi≲fp0 \lesssim f_s, f_i \lesssim f_p0≲fs​,fi​≲fp​, where fsf_sfs​, fif_ifi​ and fpf_pfp​ are the signal, idler and pump frequencies, respectively, obeying relation fs+fi=fpf_s + f_i = f_pfs​+fi​=fp​. Estimation of the amplifier characteristics with typical experimental parameters, number of cells NNN = 700, length of 28 mm and pump frequency of 12.5 GHz yields a flat (-3 dB) gain of about 20 dB in the bandwidth from 3.35 GHz to 9.15 GHz and a saturation power of -90 dBm.
Bringing signals from quantum to classical, from few-photon to many-photon levels for further processing, is a common challenge in rising quantum technologies. These include quantum computing, quantum communication, quantum sensing, radio astronomy, and dark matter searches, typically operating at microwave frequencies and millikelvin temperatures. Superconducting parametric amplifiers, as the first piece in the readout chain, have become a cornerstone of these technologies, since they offer unrivaled noise performance near the quantum-mechanical limit and high gain to surpass the noise of subsequent amplifiers. A notable implementation is the Josephson traveling-wave parametric amplifier (TWPA), which stands out due to its bandwidth of several Gigahertz and high saturation power, often larger than -100 dBm. These key properties come at the cost of complexity in design and fabrication: TWPA metamaterials often contain several thousands of Josephson junctions. Designing high-gain TWPAs involves three major challenges: ensuring impedance-matching, phase-matching of parametric amplification, and suppressing unwanted processes, all achievable through sub-wavelength dispersion engineering. This thesis covers the circuit design and analysis, implementation, and experimental characterization of a dispersion-engineered TWPA based on radio-frequency superconducting interference devices (rf-SQUIDs). It focuses on a detailed investigation of dispersion-engineering techniques and their effects on amplifier performance, particularly through the use of time-domain circuit simulations to analyze the multimode dynamics of the circuit. The experimentally realized device features 18 dB of gain, an instantaneous bandwidth spanning from 2.2 to 6.7 GHz, a system noise of 2.5 quanta, and a saturation power of (−86.5 ± 4.0) dBm. With these characteristics, it is suitable for frequency-multiplexed readout of detector arrays or qubits. Its high saturation power, about 10 dB higher than other reported Josephson-junction-based TWPAs, allows increasing the number of qubits per readout line, or decreasing the intermodulation between frequency-multiplexed qubits, both crucial for scaling up quantum computation.
We report on the implementation of a near-quantum-limited, traveling-wave parametric amplifier that uses three-wave mixing (3WM). To favor amplification by 3WM, we use superconducting nonlinear asymmetric inductive element (SNAIL) loops, biased with a dc magnetic flux. In addition, we equip the device with dispersion engineering features to create a stopband at the second harmonic of the pump and suppress the propagation of the higher harmonics that otherwise degrade the amplification. With a chain of 440 SNAILs, the amplifier provides up to 20 dB gain and a 3-dB bandwidth of 1 GHz. The added noise by the amplifier is found to be less than one photon.
With potentially quantum limited performance and wide frequency bandwidth, traveling-wave Josephson parametric amplifiers (TWJPAs) based on superconducting circuits are in urgent demand for quantum information processing. This study designs a TWJPA in which the interacting pump and signal/idler microwaves propagate with similar phase velocities through two different transmission lines, thereby enabling parametric gain. Such operation is possible due to a chain of SQUIDs that form the signal transmission line, which is magnetically coupled to a separate pump $L\phantom{\rule{0}{0ex}}C$ line. The proposed circuit may greatly simplify the measurement setup and solve the problem of pump depletion.