Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2205.08016 · Scientific Reports

Addressable superconductor integrated circuit memory from delay lines

Jennifer E. Volk, Alex Wynn, Evan B. Golden, Timothy Sherwood, Georgios Tzimpragos

Published Oct 3, 2023• 11 citations
arXivHTMLPDF

Abstract

Abstract Recent advances in logic schemes and fabrication processes have renewed interest in using superconductor electronics for energy-efficient computing and quantum control processors. However, scalable superconducting memory still poses a challenge. To address this issue, we present an alternative to approaches that solely emphasize storage cell miniaturization by exploiting the minimal attenuation and dispersion properties of superconducting passive transmission lines to develop a delay-line memory system. This fully superconducting design operates at speeds between 20 and 100 GHz, with ± 24% and ± 13% bias margins, respectively, and demonstrates data densities in the 10s of Mbit/cm 2 with the MIT Lincoln Laboratory SC2 fabrication process. Additionally, the circulating nature of this design allows for minimal control circuitry, eliminates the need for data splitting and merging, and enables inexpensive implementations of sequential access and content-addressable memories. Further advances in fabrication processes suggest data densities of 100s of Mbit/cm 2 and beyond.

DOI
10.1038/s41598-023-43205-8

Related papers

Very Large Scale Integration of Josephson-Junction-Based Superconductor Random Access Memories

Vasili K. Semenov, Yuri A. Polyakov, Sergey K. Tolpygo

Arrays of vortex transitional (VT) memory cells with functional density up to 1 Mbit/cm2have been designed, fabricated, and successfully demonstrated. This progress is due to recent advances in design optimization and in superconductor electronics fabrication achieved at MIT Lincoln Laboratory. As a starting point, we developed a demo array of VT cells for the 100-μA/μm2MIT LL fabrication process SFQ5ee with eight niobium layers. The studied two-junction memory cell with a two-junction nondestructive readout occupied 168 μm2, resulting in an over 0.5 Mbit/cm2functional density. Then, we reduced the cell area down to 99 μm2(corresponding to over 0.9 Mbit/cm2functional density) by utilizing self-shunted Josephson junctions (JJs) with critical current density JC of 600 μA/μm2and eliminating shunt resistors. The fabricated high-JC memory cells were fully operational and possessed wide read/write current margins, quite close to the theoretically predicted values. We discuss approaches to further increasing the integration scale of superconductor memory and logic circuits: 1) miniaturization of superconducting transformers by using soft magnetic materials; and 2) reduction of JJ area by using planar high-JC junctions similar to variable thickness bridges.

arXiv:1902.08302•IEEE Transactions on Applied Superconductivity•Mar 18, 2019•66 citations

Access Time and Power Dissipation of a Model 256-Bit Single Flux Quantum RAM

Thomas Ortlepp, T. Van Duzer

Superconductor electronics offers logic circuits for high-speed data processing and high-performance computing. The main barrier to practical application is the lack of high-speed and low-power memory. It is widely believed that the most reliable and functional bit cell for superconducting memory is the vortex transitional bit cell, which was successfully used by Nagasawa in a 4-kb memory. This paper reviews existing challenges in this type of Josephson memory devices and discusses engineering issues in implementing a model single flux quantum random access memory. We evaluate the contributions that various components of the memory system make to delay and power dissipation. The 256-bit memory provides an experimentally confirmed read access time of 190 ps. As a result, we found that delay and power dissipation are found largely in the address decoder, line drivers, bit-selection scheme, and the data readout circuitry. With these circuits being similar for various magnetic memory devices, our findings provide essential data for a comprehensive assessment of new concepts for bit cells, readout, and write in superconducting memories.

IEEE Transactions on Applied Superconductivity•Apr 22, 2014•23 citations

Increasing integration scale of superconductor electronics beyond one million Josephson junctions

Sergey K. Tolpygo, Vasili K. Semenov

Abstract We review the existing fabrication processes for superconductor digital electronics and describe approaches to increasing the scale of integration of superconducting digital circuits from the current level of about one million Josephson junctions (JJs) on a 1-cm 2 chip toward ten million JJs per chip. We present designs of ac-clocked Single Flux Quantum (SFQ) shift registers, convenient benchmarking circuits, in a 250-nm-linewidth superconductor electronics fabrication process developed recently at MIT Lincoln Laboratory (MIT LL). For shift registers using resistively shunted JJs with Josephson critical current density, J c of 100 μA/μm 2 , we achieved a record-high circuit density of 4.2·10 6 JJs per cm 2 , a factor of three higher than the previous record obtained in the MIT LL 350-nm-linewidth SFQ5ee process. Using self-shunted JJs with J c of 600 μA/μm 2 , we increased this record circuit density to 7.4·10 6 JJs per cm 2 .

Journal of Physics Conference Series•Jun 1, 2020•37 citations

Potential of superconductive josephson tunneling technology for ultrahigh performance memories and processors

W. Anacker

The potential of a new technology, based on the superconducting Josephson tunneling effect, has been assessed for use in high-speed computer systems. Josephson tunneling circuits for memory and logic functions can be switched at sub-nanosecond delay, do not require standby power, and dissipate extremely low energy, typically less than 10-13joule during fast switching operation. High-speed circuits with high packing densities, not limited by power dissipation problems, can therefore be expected. Low thermal noise at cryogenic temperatures ensures reliable operation despite the low energy switching signal. Practically lossless signal transmission via superconducting lines can be exploited for high-speed operation even when sizeable memory and logic modules are assembled. Two random access memory modules have been designed on the basis of single device experiments. Operational characteristics leading to the conclusion that 30 Mbit capacity, less than 1 watt refrigeration requirement (at 3.6° K) and cycle times of 40 ns (in one case) and 15 ns (in the second case), can be achieved are presented.

IEEE Transactions on Magnetics•Dec 1, 1969•72 citations

Design and Implementation of a Single Flux Quantum Logic-Based Memory Controller for Josephson-CMOS Hybrid Memory Systems

Seda Demirhan, Ali Bozbey

Single flux quantum (SFQ) digital circuits have shown the potential for high speed/low power computation applications. Unfortunately, because of the low integration density and low driving capability of SFQ circuits, realizing large-scale memories by using only SFQ circuits is still a challenge. Josephson-CMOS hybrid memory, hybridizing high-speed, low power SFQ circuits, and high-density CMOS memories is already proposed as a solution to the large-scale memory problem in RSFQ digital systems. In this article, an SFQ-based memory controller which works up to 10 GHz clock frequencies is designed for Josephson-CMOS hybrid memory systems. The memory controller acts as a SFQ/CMOS interface between the SFQ circuit and SRAM module and generates the required waveforms for SRAM read and write operations. The circuit which has 4-b data and 2-b address lines is fabricated with AIST 2.5 kA/cm2STP2 process and operations of the circuits are verified. To demonstrate the scalability of the circuit, memory controller was scaled to 8-b data and 13-b address to control of the 64kb SRAM. Operations of the scaled memory controller are verified with analog simulations. Scaled circuit consumes 0.76 mW power in an area of 1.64 mm × 1.60 mm.

IEEE Transactions on Applied Superconductivity•Jul 28, 2020•5 citations

Design and Demonstration of a 30 GHz 16-bit Superconductor RSFQ Microprocessor

M. Dorojevets

Abstract : The major objective of the project was to design and demonstrate operation of key components of a 30 GHz 16-bit RSFQ processor prototype implemented with the AIST/ISTEC 10 kA/cm sq. fabrication process. Our team has developed complete logical and physical designs of five RSFQ chips using the CONNECT cell library and RSFQ CAD tools developed at the Universities of Yokohama and Nagoya (Japan). The major results are the world's first successful design, fabrication, and demonstration of correct operation of a 20 GHz 8x8-bit parallel carry-save RSFQ multiplier with approximately 6K JJs, a 16-bit sparse-tree wave-pipelined RSFQ adder with approximately 10K JJs, and partial operation of an 8-bit ALU chip with approximately 9K JJs. The goal of the second phase of the project was to get detailed understanding of the performance, complexity, and energy efficiency of on-chip storage units implemented with superconductor Reciprocal Quantum Logic (RQL) using our RQL VHDL cell library tuned to the MIT Lincoln Laboratory 10 kA/cm2 248 nm process. The 8.5 GHz 1-4 Kbit 32-/64-bit multi-ported scratchpad memory, register files, write-through and write-back caches designed with RQL Non-Destructive Read-Out storage cells have the average energy consumption of 3.0-9.5 fJ/bit/operation at room temperature using the cryocooling efficiency of 0.1%.

•Mar 10, 2015•1 citation
Abstract Recent advances in logic schemes and fabrication processes have renewed interest in using superconductor electronics for energy-efficient computing and quantum control processors. However, scalable superconducting memory still poses a challenge. To address this issue, we present an alternative to approaches that solely emphasize storage cell miniaturization by exploiting the minimal attenuation and dispersion properties of superconducting passive transmission lines to develop a delay-line memory system. This fully superconducting design operates at speeds between 20 and 100 GHz, with ± 24% and ± 13% bias margins, respectively, and demonstrates data densities in the 10s of Mbit/cm 2 with the MIT Lincoln Laboratory SC2 fabrication process. Additionally, the circulating nature of this design allows for minimal control circuitry, eliminates the need for data splitting and merging, and enables inexpensive implementations of sequential access and content-addressable memories. Further advances in fabrication processes suggest data densities of 100s of Mbit/cm 2 and beyond.
Arrays of vortex transitional (VT) memory cells with functional density up to 1 Mbit/cm2have been designed, fabricated, and successfully demonstrated. This progress is due to recent advances in design optimization and in superconductor electronics fabrication achieved at MIT Lincoln Laboratory. As a starting point, we developed a demo array of VT cells for the 100-μA/μm2MIT LL fabrication process SFQ5ee with eight niobium layers. The studied two-junction memory cell with a two-junction nondestructive readout occupied 168 μm2, resulting in an over 0.5 Mbit/cm2functional density. Then, we reduced the cell area down to 99 μm2(corresponding to over 0.9 Mbit/cm2functional density) by utilizing self-shunted Josephson junctions (JJs) with critical current density JC of 600 μA/μm2and eliminating shunt resistors. The fabricated high-JC memory cells were fully operational and possessed wide read/write current margins, quite close to the theoretically predicted values. We discuss approaches to further increasing the integration scale of superconductor memory and logic circuits: 1) miniaturization of superconducting transformers by using soft magnetic materials; and 2) reduction of JJ area by using planar high-JC junctions similar to variable thickness bridges.
Superconductor electronics offers logic circuits for high-speed data processing and high-performance computing. The main barrier to practical application is the lack of high-speed and low-power memory. It is widely believed that the most reliable and functional bit cell for superconducting memory is the vortex transitional bit cell, which was successfully used by Nagasawa in a 4-kb memory. This paper reviews existing challenges in this type of Josephson memory devices and discusses engineering issues in implementing a model single flux quantum random access memory. We evaluate the contributions that various components of the memory system make to delay and power dissipation. The 256-bit memory provides an experimentally confirmed read access time of 190 ps. As a result, we found that delay and power dissipation are found largely in the address decoder, line drivers, bit-selection scheme, and the data readout circuitry. With these circuits being similar for various magnetic memory devices, our findings provide essential data for a comprehensive assessment of new concepts for bit cells, readout, and write in superconducting memories.
Abstract We review the existing fabrication processes for superconductor digital electronics and describe approaches to increasing the scale of integration of superconducting digital circuits from the current level of about one million Josephson junctions (JJs) on a 1-cm 2 chip toward ten million JJs per chip. We present designs of ac-clocked Single Flux Quantum (SFQ) shift registers, convenient benchmarking circuits, in a 250-nm-linewidth superconductor electronics fabrication process developed recently at MIT Lincoln Laboratory (MIT LL). For shift registers using resistively shunted JJs with Josephson critical current density, J c of 100 μA/μm 2 , we achieved a record-high circuit density of 4.2·10 6 JJs per cm 2 , a factor of three higher than the previous record obtained in the MIT LL 350-nm-linewidth SFQ5ee process. Using self-shunted JJs with J c of 600 μA/μm 2 , we increased this record circuit density to 7.4·10 6 JJs per cm 2 .
The potential of a new technology, based on the superconducting Josephson tunneling effect, has been assessed for use in high-speed computer systems. Josephson tunneling circuits for memory and logic functions can be switched at sub-nanosecond delay, do not require standby power, and dissipate extremely low energy, typically less than 10-13joule during fast switching operation. High-speed circuits with high packing densities, not limited by power dissipation problems, can therefore be expected. Low thermal noise at cryogenic temperatures ensures reliable operation despite the low energy switching signal. Practically lossless signal transmission via superconducting lines can be exploited for high-speed operation even when sizeable memory and logic modules are assembled. Two random access memory modules have been designed on the basis of single device experiments. Operational characteristics leading to the conclusion that 30 Mbit capacity, less than 1 watt refrigeration requirement (at 3.6° K) and cycle times of 40 ns (in one case) and 15 ns (in the second case), can be achieved are presented.
Single flux quantum (SFQ) digital circuits have shown the potential for high speed/low power computation applications. Unfortunately, because of the low integration density and low driving capability of SFQ circuits, realizing large-scale memories by using only SFQ circuits is still a challenge. Josephson-CMOS hybrid memory, hybridizing high-speed, low power SFQ circuits, and high-density CMOS memories is already proposed as a solution to the large-scale memory problem in RSFQ digital systems. In this article, an SFQ-based memory controller which works up to 10 GHz clock frequencies is designed for Josephson-CMOS hybrid memory systems. The memory controller acts as a SFQ/CMOS interface between the SFQ circuit and SRAM module and generates the required waveforms for SRAM read and write operations. The circuit which has 4-b data and 2-b address lines is fabricated with AIST 2.5 kA/cm2STP2 process and operations of the circuits are verified. To demonstrate the scalability of the circuit, memory controller was scaled to 8-b data and 13-b address to control of the 64kb SRAM. Operations of the scaled memory controller are verified with analog simulations. Scaled circuit consumes 0.76 mW power in an area of 1.64 mm × 1.60 mm.
Abstract : The major objective of the project was to design and demonstrate operation of key components of a 30 GHz 16-bit RSFQ processor prototype implemented with the AIST/ISTEC 10 kA/cm sq. fabrication process. Our team has developed complete logical and physical designs of five RSFQ chips using the CONNECT cell library and RSFQ CAD tools developed at the Universities of Yokohama and Nagoya (Japan). The major results are the world's first successful design, fabrication, and demonstration of correct operation of a 20 GHz 8x8-bit parallel carry-save RSFQ multiplier with approximately 6K JJs, a 16-bit sparse-tree wave-pipelined RSFQ adder with approximately 10K JJs, and partial operation of an 8-bit ALU chip with approximately 9K JJs. The goal of the second phase of the project was to get detailed understanding of the performance, complexity, and energy efficiency of on-chip storage units implemented with superconductor Reciprocal Quantum Logic (RQL) using our RQL VHDL cell library tuned to the MIT Lincoln Laboratory 10 kA/cm2 248 nm process. The 8.5 GHz 1-4 Kbit 32-/64-bit multi-ported scratchpad memory, register files, write-through and write-back caches designed with RQL Non-Destructive Read-Out storage cells have the average energy consumption of 3.0-9.5 fJ/bit/operation at room temperature using the cryocooling efficiency of 0.1%.