Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2203.09676 · Optics Letters

In situ probing and stabilizing the power ratio of electro-optic-modulated laser pairs based on VIPA etalon for quantum sensing

Guochao Wang, Mingyue Yang, Enlong Wang, Xu Zhang, Aiai Jia, Lingxiao Zhu, Shuhua Yan, Jun Yang

Published May 24, 2022• 1 citation
arXivHTMLPDF

Abstract

Monitoring and stabilizing the power ratio of laser pairs is significant for high-precision atom interferometers, especially as the compact electro-optic-modulated all-fiber laser system prevails. In this Letter, we demonstrate a novel, to the best of our knowledge, method to in situ probe the relative power of laser pairs and to stabilize the power ratio of two Raman lasers using a high-dispersion virtually imaged phased array (VIPA) etalon. Sub-microsecond resolution on probing laser power transformation during the atom interferometer sequence is achieved and the power ratio of two Raman lasers (PRTR) is tightly locked with high bandwidth despite environmental disturbances, showing an Allan deviation of 4.39 × 10−5 at 1000 s averaging time. This method provides a novel way to stabilize the PRTR and diagnose multi-frequency laser systems for atom interferometers, and it could find potential applications in broad quantum sensing scenarios.

DOI
10.1364/ol.458844

Related papers

Stabilizing Electro-Optic Modulation Depth With Carrier to Sideband Ratio by Intermediate Optical Beatings

Jie Wang, Guochao Wang, Yaning Wang +9 more

Electro-optic modulation with a constant modulation depth plays important roles in quantum metrology, microwave photonics, and optical precision measurement and sensing, etc. To compensate the continuous drift of the half-wave voltage and maintain the modulation depth, we incidentally generated a reference laser to make intermedia optical beatings with the carrier and +1st sideband, and tightly locked the carrier to sideband ratio by extracting the relative microwave power of those intermedia beat signals using a home-made electronic control module. Experiments of the short-term test for locking bandwidth, the anti-jamming capability, and the long-term stability were demonstrated. As is verified that, the locking bandwidth was estimated up to tens of kHz, and the anti-jamming capability was confirmed despite of a strong hair-dryer agitation. The long-term stability for the modulation depth stabilization showed that the peak-to-peak relative stability for 150-minute was 5.67 × 10−6, and the Allan deviation reached a minimum of 2.19 × 10−7at an averaging time of 400 s, which is improved by more than four orders of magnitude compared with the open-loop regime. We believe the reported method as well as the designed module is versatile and potential to precision measurement and sensing applications badly requiring a stable modulation depth, such as atom interferometry, optical interferometry and lidar detection.

IEEE photonics journal•Oct 20, 2021•1 citation

A new method for high-bandwidth servo control of the power ratio between two Raman beams for cold atom interferometer

Yaning Wang, Huankai Zhang, Dongyang Xu +8 more

Light shift produced by the AC Stark effect is one of the major factors limiting the accuracy and long-term stability of a cold atom interferometer. The first order light shift can be canceled by fixing the power ratio of the Raman beams at a specified value. We report here a new method to stabilize the power ratio of the two Raman lasers with ∼100 kHz locking bandwidth, suppressing the effect of the first order light shift. We first mixed the two Raman lasers (at different optical frequencies) with a reference beam and then used two Schottky diode detectors to extract the corresponding beat note signals for each beam, which are much easier to be manipulated and processed as they are in the microwave band. The stability of the power ratio is improved by three orders of magnitude from 5.84 × 10−3 to 3.51 × 10−6 at 1 s averaging time and reaches 1.59 × 10−7 at 10 000 s integrating time when the servo loop is engaged. This method can be used in other precise quantum measurement based on the stimulated Raman transition and can be applied to compact inertial sensors.

Review of Scientific Instruments•Oct 1, 2020•5 citations

A phase-modulated laser system of ultra-low phase noise for compact atom interferometers

Ki-Se Lee, Jaewan Kim, Sang-Bum Lee +2 more

A compact and robust laser system is essential for mobile atom interferometers. Phase modulation can provide the two necessary phase-coherent frequencies without sophisticated phase-locking between two different lasers. However, the additional laser frequencies generated can perturb the atom interferometer. In this article, we report on a novel method to produce a single high-power laser beam composed of two phase-coherent sidebands without the perturbing carrier mode. Light from a diode laser is phase-modulated by using a fiber-coupled electro-optic modulator driven at 3.4 GHz and passes through a Fabry-Perot cavity with a 6.8 GHz free spectral range. The cavity filters the carrier mode to leave the two first-order sidebands for the two-photon Raman transition between the two hyperfine ground states of 87 Rb. The laser beam is then fed to a single tapered amplifier, and the two sidebands are both amplified without mode competition. The phase noise is lower than that of a state-of-the-art optically phase-locked external-cavity diode laser (−135 dBrad 2 /Hz at 10 kHz) at frequencies above 10 Hz. This technique can be used in all-fiber-based laser systems for future mobile atom interferometers.

Journal of the Korean Physical Society•Jul 1, 2015•13 citations

Laser frequency locking method for Rydberg atomic sensing

Kai Yang, Ruiqi Mao, Qiang An +2 more

Based on the Rydberg cascade electromagnetically induced transparency, we propose a simultaneous dual-wavelength locking method for Rydberg atomic sensing at room temperature.The simplified frequency-locking configuration uses only one signal generator and one electro-optic modulator, realizing real-time feedback for both lasers.We studied the effect of the different probe and coupling laser powers on the error signal.In addition, the Allan variance and a 10 kHz amplitudemodulated signal are introduced to evaluate the performance of the laser frequency stabilization.In principle, the laser frequency stabilization method presented here can be extended to any cascade Rydberg atomic system.

Chinese Optics Letters•Nov 16, 2022•23 citations

Injection locking of Raman laser beams in cold atom interferometers

Ling Wang, Yao Zhanwei, Xiong Zong-yuan +3 more

Raman pulse sequences are generally used to coherently manipulate the atomic wave packet in an atom interferometer.High power Raman beams allow more atoms join in the velocity-sensitive stimulated Raman transition,and that will be helpful for obtaining high signal to noise ratio in atom interferometer fringe.Development of high power Raman laser is important for cold atom interferometer experiments.The experimental realization of high power Raman lasers are demonstrated based on injection locking technique. Master laser is modulated by a 1.5 GHz acousto-optical modulator,and the±1 order diffraction lights are used as seeding Raman lasers.The seeding lasers are injection locked to two slave lasers which are further amplified as Raman beams.The frequency difference of Raman beams is 3.0 GHz,and the detuning range is about 200 MHz.

Chinese Journal of Quantum Electronics•Jan 1, 2012•0 citations

Phase stabilization of laser beams in a cold atom accelerometer

Nicole Byrne

A cold atom accelerometer measures the displacement of a proof mass of laser cooled atoms with respect to an instrument reference frame. The cold atom interferometer's reference frame is defined by a pair of specially prepared, counter-propagating laser beams, that measure inertially induced atom displacements with nm scale resolution. This corresponds to acceleration sensitivities comparable to state of the art electro-mechanical accelerometers. In dynamic environments, sensitivity is limited by the stability of the relative laser phase of the two interrogation laser beams, which is adversely affected by vibrations and temperature fluctuations of the interrogation beam optics. Without an independent measurement, the cold atom interferometer cannot distinguish platform acceleration from laser phase fluctuations, which thus are a potentially serious source of error. In this thesis, a Michelson optical interferometer and an optical feedback loop were used to stabilize the relative phase of the interrogation laser beams in a cold atom accelerometer. A digital controller stabilized the relative phase via an electro-optic phase modulator. This control loop's bandwidth encompasses 98.8% of the noise power as determined from the power spectral density of the open loop 795nm Michelson signal. Increasing the controller bandwidth would gain the system marginal improvement in noise reduction. At an atom interferometer dwell time of 1 msec, active laser phase stabilization improved the atom interferometer sensitivity; at an atom interferometer dwell time of 8msec, an improvement was no longer evident. Improvements to the laser phase stabilization system are proposed to increase atom interferometer stability at longer dwell times.

•Jan 1, 2014•0 citations
Monitoring and stabilizing the power ratio of laser pairs is significant for high-precision atom interferometers, especially as the compact electro-optic-modulated all-fiber laser system prevails. In this Letter, we demonstrate a novel, to the best of our knowledge, method to in situ probe the relative power of laser pairs and to stabilize the power ratio of two Raman lasers using a high-dispersion virtually imaged phased array (VIPA) etalon. Sub-microsecond resolution on probing laser power transformation during the atom interferometer sequence is achieved and the power ratio of two Raman lasers (PRTR) is tightly locked with high bandwidth despite environmental disturbances, showing an Allan deviation of 4.39 × 10−5 at 1000 s averaging time. This method provides a novel way to stabilize the PRTR and diagnose multi-frequency laser systems for atom interferometers, and it could find potential applications in broad quantum sensing scenarios.
Electro-optic modulation with a constant modulation depth plays important roles in quantum metrology, microwave photonics, and optical precision measurement and sensing, etc. To compensate the continuous drift of the half-wave voltage and maintain the modulation depth, we incidentally generated a reference laser to make intermedia optical beatings with the carrier and +1st sideband, and tightly locked the carrier to sideband ratio by extracting the relative microwave power of those intermedia beat signals using a home-made electronic control module. Experiments of the short-term test for locking bandwidth, the anti-jamming capability, and the long-term stability were demonstrated. As is verified that, the locking bandwidth was estimated up to tens of kHz, and the anti-jamming capability was confirmed despite of a strong hair-dryer agitation. The long-term stability for the modulation depth stabilization showed that the peak-to-peak relative stability for 150-minute was 5.67 × 10−6, and the Allan deviation reached a minimum of 2.19 × 10−7at an averaging time of 400 s, which is improved by more than four orders of magnitude compared with the open-loop regime. We believe the reported method as well as the designed module is versatile and potential to precision measurement and sensing applications badly requiring a stable modulation depth, such as atom interferometry, optical interferometry and lidar detection.
Light shift produced by the AC Stark effect is one of the major factors limiting the accuracy and long-term stability of a cold atom interferometer. The first order light shift can be canceled by fixing the power ratio of the Raman beams at a specified value. We report here a new method to stabilize the power ratio of the two Raman lasers with ∼100 kHz locking bandwidth, suppressing the effect of the first order light shift. We first mixed the two Raman lasers (at different optical frequencies) with a reference beam and then used two Schottky diode detectors to extract the corresponding beat note signals for each beam, which are much easier to be manipulated and processed as they are in the microwave band. The stability of the power ratio is improved by three orders of magnitude from 5.84 × 10−3 to 3.51 × 10−6 at 1 s averaging time and reaches 1.59 × 10−7 at 10 000 s integrating time when the servo loop is engaged. This method can be used in other precise quantum measurement based on the stimulated Raman transition and can be applied to compact inertial sensors.
A compact and robust laser system is essential for mobile atom interferometers. Phase modulation can provide the two necessary phase-coherent frequencies without sophisticated phase-locking between two different lasers. However, the additional laser frequencies generated can perturb the atom interferometer. In this article, we report on a novel method to produce a single high-power laser beam composed of two phase-coherent sidebands without the perturbing carrier mode. Light from a diode laser is phase-modulated by using a fiber-coupled electro-optic modulator driven at 3.4 GHz and passes through a Fabry-Perot cavity with a 6.8 GHz free spectral range. The cavity filters the carrier mode to leave the two first-order sidebands for the two-photon Raman transition between the two hyperfine ground states of 87 Rb. The laser beam is then fed to a single tapered amplifier, and the two sidebands are both amplified without mode competition. The phase noise is lower than that of a state-of-the-art optically phase-locked external-cavity diode laser (−135 dBrad 2 /Hz at 10 kHz) at frequencies above 10 Hz. This technique can be used in all-fiber-based laser systems for future mobile atom interferometers.
Based on the Rydberg cascade electromagnetically induced transparency, we propose a simultaneous dual-wavelength locking method for Rydberg atomic sensing at room temperature.The simplified frequency-locking configuration uses only one signal generator and one electro-optic modulator, realizing real-time feedback for both lasers.We studied the effect of the different probe and coupling laser powers on the error signal.In addition, the Allan variance and a 10 kHz amplitudemodulated signal are introduced to evaluate the performance of the laser frequency stabilization.In principle, the laser frequency stabilization method presented here can be extended to any cascade Rydberg atomic system.
Raman pulse sequences are generally used to coherently manipulate the atomic wave packet in an atom interferometer.High power Raman beams allow more atoms join in the velocity-sensitive stimulated Raman transition,and that will be helpful for obtaining high signal to noise ratio in atom interferometer fringe.Development of high power Raman laser is important for cold atom interferometer experiments.The experimental realization of high power Raman lasers are demonstrated based on injection locking technique. Master laser is modulated by a 1.5 GHz acousto-optical modulator,and the±1 order diffraction lights are used as seeding Raman lasers.The seeding lasers are injection locked to two slave lasers which are further amplified as Raman beams.The frequency difference of Raman beams is 3.0 GHz,and the detuning range is about 200 MHz.
A cold atom accelerometer measures the displacement of a proof mass of laser cooled atoms with respect to an instrument reference frame. The cold atom interferometer's reference frame is defined by a pair of specially prepared, counter-propagating laser beams, that measure inertially induced atom displacements with nm scale resolution. This corresponds to acceleration sensitivities comparable to state of the art electro-mechanical accelerometers. In dynamic environments, sensitivity is limited by the stability of the relative laser phase of the two interrogation laser beams, which is adversely affected by vibrations and temperature fluctuations of the interrogation beam optics. Without an independent measurement, the cold atom interferometer cannot distinguish platform acceleration from laser phase fluctuations, which thus are a potentially serious source of error. In this thesis, a Michelson optical interferometer and an optical feedback loop were used to stabilize the relative phase of the interrogation laser beams in a cold atom accelerometer. A digital controller stabilized the relative phase via an electro-optic phase modulator. This control loop's bandwidth encompasses 98.8% of the noise power as determined from the power spectral density of the open loop 795nm Michelson signal. Increasing the controller bandwidth would gain the system marginal improvement in noise reduction. At an atom interferometer dwell time of 1 msec, active laser phase stabilization improved the atom interferometer sensitivity; at an atom interferometer dwell time of 8msec, an improvement was no longer evident. Improvements to the laser phase stabilization system are proposed to increase atom interferometer stability at longer dwell times.