Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2203.09592 · Physical Review Applied

Compact Superconducting Microwave Resonators Based on Al-AlOx -Al Capacitors

Julia Zotova, Rui Wang, Alexander V. Semenov, Yu Zhou, Ivan Khrapach, Akiyoshi Tomonaga, O. V. Astafiev, Jaw-Shen Tsai

Published Apr 24, 2023• 14 citations
arXivHTMLPDF

Abstract

We address the scaling-up problem for superconducting quantum circuits by using lumped-element resonators based on an alternative fabrication method of aluminum-aluminum oxide-aluminum (Al-${\mathrm{AlO}}_{x}$-Al) parallel-plate capacitors. The size of the resonators is only $0.04\phantom{\rule{0.2em}{0ex}}{\mathrm{mm}}^{2}$, which is more than one order smaller than the typical size of coplanar resonators ($1\phantom{\rule{0.2em}{0ex}}{\mathrm{mm}}^{2}$). The fabrication method we develop easily fits into the standard superconducting qubit fabrication process. We obtain capacitance per area $14\phantom{\rule{0.2em}{0ex}}\mathrm{fF}/\text{\ensuremath{\mu}}{\mathrm{m}}^{2}$ and the internal quality factor $1\ifmmode\times\else\texttimes\fi{}{10}^{3}$--$8\ifmmode\times\else\texttimes\fi{}{10}^{3}$ at the single-photon level. Our results show that such devices based on Al-${\mathrm{AlO}}_{x}$-Al capacitors could be further applied to the qubit readout scheme, including resonators, filters, amplifiers, as well as microwave metamaterials and innovative types of qubits, such as $0\ensuremath{-}\ensuremath{\pi}$ qubit.

DOI
10.1103/physrevapplied.19.044067

Related papers

Fabrication and characterization of low-loss Al/Si/Al parallel plate capacitors for superconducting quantum information applications

Anthony McFadden, Aranya Goswami, Tongyu Zhao +7 more

Abstract Increasing the density of superconducting circuits requires compact components, however, superconductor-based capacitors typically perform worse as dimensions are reduced due to loss at surfaces and interfaces. Here, parallel plate capacitors composed of aluminum-contacted, crystalline silicon fins are shown to be a promising technology for use in superconducting circuits by evaluating the performance of lumped element resonators and transmon qubits. High aspect ratio Si-fin capacitors having widths below 300 nm with an approximate total height of 3 μm are fabricated using anisotropic wet etching of Si(110) substrates followed by aluminum metallization. The single-crystal Si capacitors are incorporated in lumped element resonators and transmons by shunting them with lithographically patterned aluminum inductors and conventional A l/A l O x /A l Josephson junctions respectively. Microwave characterization of these devices suggests state-of-the-art performance for superconducting parallel plate capacitors with low power internal quality factor of lumped element resonators greater than 500 k and qubit T 1 times greater than 25 μs. These results suggest that Si-Fins are a promising technology for applications that require low-loss, compact, superconductor-based capacitors with minimal stray capacitance.

arXiv:2408.01369•npj Quantum Information•Jan 22, 2025•11 citations

Characterization of superconducting through-silicon vias as capacitive elements in quantum circuits

Thomas Hazard, Wayne H. Woods, Danna Rosenberg +13 more

The large physical size of superconducting qubits and their associated on-chip control structures presents a practical challenge toward building a large-scale quantum computer. In particular, transmons require a high-quality-factor shunting capacitance that is typically achieved by using a large coplanar capacitor. Other components, such as superconducting microwave resonators used for qubit state readout, are typically constructed from coplanar waveguides, which are millimeters in length. Here, we use compact superconducting through-silicon vias to realize lumped-element capacitors in both qubits and readout resonators to significantly reduce the on-chip footprint of both of these circuit elements. We measure two types of devices to show that through-silicon vias are of sufficient quality to be used as capacitive circuit elements and provide a significant reduction in size over existing approaches.

arXiv:2308.00834•Applied Physics Letters•Oct 9, 2023•15 citations

Single crystal silicon capacitors with low microwave loss in the single photon regime

Steven J. Weber, Kater W. Murch, D. H. Slichter +2 more

We have fabricated superconducting microwave resonators in a lumped element geometry using single crystal silicon dielectric parallel plate capacitors with C>2 pF. Aluminum devices with resonant frequencies between 4.0 and 6.5 GHz exhibited an average internal quality factor Qi of 2×105 in the single photon excitation regime at T=20 mK. Attributing the observed loss solely to the capacitive element, our measurements place an upper bound on the loss tangent of the silicon dielectric layer of tan δi=5×10−6. This level of loss is an order of magnitude lower than is currently observed in structures incorporating amorphous dielectric materials, thus making single crystal silicon capacitors an attractive, robust route for realizing long-lived quantum circuits.

arXiv:1102.2917•Applied Physics Letters•Apr 25, 2011•59 citations

Development of high quality superconducting resonators for quantum device applications

Dong-Gwang Ha, Seon Hoo Kim, So-Yeon Jun +5 more

We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•0 citations

Loss Dependence on Geometry and Applied Power in Superconducting Coplanar Resonators

Moe S. Khalil, F. C. Wellstood, Kevin D. Osborn

The loss in superconducting microwave resonators at low-photon numbers and low temperatures is not well understood but has implications for achievable coherence times in superconducting qubits. We have fabricated single-layer resonators with a high quality factor by patterning a superconducting aluminum film on a sapphire substrate. Four resonator geometries were studied with resonant frequencies ranging from 5 to 7 GHz: a quasi-lumped element resonator, a coplanar strip waveguide resonator, and two hybrid designs that contain both a coplanar strip and a quasi-lumped element. Transmitted power measurements were taken at 30 mK as a function of frequency and probe power. We find that the resonator loss, expressed as the inverse of the internal quality factor, decreases slowly over four decades of photon number in a manner not merely explained by loss from a conventional uniform spatial distribution of two-level systems in an oxide layer on the superconducting surfaces of the resonator.

arXiv:1008.2929•IEEE Transactions on Applied Superconductivity•Dec 9, 2010•73 citations

Control and readout of a transmon using a compact superconducting resonator

Julia Zotova, S. V. Sanduleanu, Gleb Fedorov +3 more

We demonstrate control and readout of a superconducting artificial atom based on a transmon qubit using a compact lumped-element resonator. The resonator consists of a parallel-plate capacitor with a wire geometric inductor. The footprint of the resonators is about 200 × 200 μm2, which is similar to the standard transmon size and one or two orders of magnitude more compact in the occupied area compared to coplanar waveguide resonators. We observe coherent Rabi oscillations and obtain time-domain properties of the transmon. The work opens a door to miniaturize essential components of superconducting circuits and to further scale up quantum systems with superconducting transmons.

arXiv:2312.15753•Applied Physics Letters•Mar 4, 2024•5 citations
We address the scaling-up problem for superconducting quantum circuits by using lumped-element resonators based on an alternative fabrication method of aluminum-aluminum oxide-aluminum (Al-AlOx{\mathrm{AlO}}_{x}AlOx​-Al) parallel-plate capacitors. The size of the resonators is only 0.04mm20.04\phantom{\rule{0.2em}{0ex}}{\mathrm{mm}}^{2}0.04mm2, which is more than one order smaller than the typical size of coplanar resonators (1mm21\phantom{\rule{0.2em}{0ex}}{\mathrm{mm}}^{2}1mm2). The fabrication method we develop easily fits into the standard superconducting qubit fabrication process. We obtain capacitance per area 14fF/\ensuremath\mum214\phantom{\rule{0.2em}{0ex}}\mathrm{fF}/\text{\ensuremath{\mu}}{\mathrm{m}}^{2}14fF/\ensuremath\mum2 and the internal quality factor 1\ifmmode×\else\texttimes\fi1031\ifmmode\times\else\texttimes\fi{}{10}^{3}1\ifmmode×\else\texttimes\fi103--8\ifmmode×\else\texttimes\fi1038\ifmmode\times\else\texttimes\fi{}{10}^{3}8\ifmmode×\else\texttimes\fi103 at the single-photon level. Our results show that such devices based on Al-AlOx{\mathrm{AlO}}_{x}AlOx​-Al capacitors could be further applied to the qubit readout scheme, including resonators, filters, amplifiers, as well as microwave metamaterials and innovative types of qubits, such as 0\ensuremath−\ensuremathπ0\ensuremath{-}\ensuremath{\pi}0\ensuremath−\ensuremathπ qubit.
Abstract Increasing the density of superconducting circuits requires compact components, however, superconductor-based capacitors typically perform worse as dimensions are reduced due to loss at surfaces and interfaces. Here, parallel plate capacitors composed of aluminum-contacted, crystalline silicon fins are shown to be a promising technology for use in superconducting circuits by evaluating the performance of lumped element resonators and transmon qubits. High aspect ratio Si-fin capacitors having widths below 300 nm with an approximate total height of 3 μm are fabricated using anisotropic wet etching of Si(110) substrates followed by aluminum metallization. The single-crystal Si capacitors are incorporated in lumped element resonators and transmons by shunting them with lithographically patterned aluminum inductors and conventional A l/A l O x /A l Josephson junctions respectively. Microwave characterization of these devices suggests state-of-the-art performance for superconducting parallel plate capacitors with low power internal quality factor of lumped element resonators greater than 500 k and qubit T 1 times greater than 25 μs. These results suggest that Si-Fins are a promising technology for applications that require low-loss, compact, superconductor-based capacitors with minimal stray capacitance.
The large physical size of superconducting qubits and their associated on-chip control structures presents a practical challenge toward building a large-scale quantum computer. In particular, transmons require a high-quality-factor shunting capacitance that is typically achieved by using a large coplanar capacitor. Other components, such as superconducting microwave resonators used for qubit state readout, are typically constructed from coplanar waveguides, which are millimeters in length. Here, we use compact superconducting through-silicon vias to realize lumped-element capacitors in both qubits and readout resonators to significantly reduce the on-chip footprint of both of these circuit elements. We measure two types of devices to show that through-silicon vias are of sufficient quality to be used as capacitive circuit elements and provide a significant reduction in size over existing approaches.
We have fabricated superconducting microwave resonators in a lumped element geometry using single crystal silicon dielectric parallel plate capacitors with C>2 pF. Aluminum devices with resonant frequencies between 4.0 and 6.5 GHz exhibited an average internal quality factor Qi of 2×105 in the single photon excitation regime at T=20 mK. Attributing the observed loss solely to the capacitive element, our measurements place an upper bound on the loss tangent of the silicon dielectric layer of tan δi=5×10−6. This level of loss is an order of magnitude lower than is currently observed in structures incorporating amorphous dielectric materials, thus making single crystal silicon capacitors an attractive, robust route for realizing long-lived quantum circuits.
We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.
The loss in superconducting microwave resonators at low-photon numbers and low temperatures is not well understood but has implications for achievable coherence times in superconducting qubits. We have fabricated single-layer resonators with a high quality factor by patterning a superconducting aluminum film on a sapphire substrate. Four resonator geometries were studied with resonant frequencies ranging from 5 to 7 GHz: a quasi-lumped element resonator, a coplanar strip waveguide resonator, and two hybrid designs that contain both a coplanar strip and a quasi-lumped element. Transmitted power measurements were taken at 30 mK as a function of frequency and probe power. We find that the resonator loss, expressed as the inverse of the internal quality factor, decreases slowly over four decades of photon number in a manner not merely explained by loss from a conventional uniform spatial distribution of two-level systems in an oxide layer on the superconducting surfaces of the resonator.
We demonstrate control and readout of a superconducting artificial atom based on a transmon qubit using a compact lumped-element resonator. The resonator consists of a parallel-plate capacitor with a wire geometric inductor. The footprint of the resonators is about 200 × 200 μm2, which is similar to the standard transmon size and one or two orders of magnitude more compact in the occupied area compared to coplanar waveguide resonators. We observe coherent Rabi oscillations and obtain time-domain properties of the transmon. The work opens a door to miniaturize essential components of superconducting circuits and to further scale up quantum systems with superconducting transmons.