Abstract The present article primarily focuses on the design of an ultra-low-noise amplifier specifically tailored for quantum applications. The circuit design places a significant emphasis on improving the noise figure, as quantum-associated applications require the circuit's noise temperature to be around 0.4 K. This requirement aims to achieve performance comparable to the Josephson Junction amplifier. Although this task presents considerable challenges, the work concentrates on engineering the circuit to minimize mismatch and reflection coefficients, while simultaneously enhancing circuit transconductance. These efforts aim to improve the noise figure as efficiently as possible. The results of this study indicate the possibility of achieving a noise figure of approximately 0.009 dB for a unique circuit design operating at 10 K. In a departure from traditional approaches, this study employs quantum mechanical theory to analyze the circuit comprehensively. By employing quantum theory, the researchers derive relationships that highlight the crucial quantities upon which the circuit design should focus to optimize the noise figure. For example, the circuit's gain power, which depends on the circuit's photonic modes, is theoretically derived and found to affect the noise figure directly. Ultimately, by merging quantum theory with engineering approaches, this study successfully designs a highly efficient circuit that significantly minimizes the noise figure in a quantum application setting.
Abstract The present article primarily focuses on the design of an ultra-low-noise amplifier specifically tailored for quantum applications. The circuit design places a significant emphasis on improving the noise figure, as quantum-associated applications require the circuit's noise temperature to be around 0.4 K. This requirement aims to achieve performance comparable to the Josephson Junction amplifier. Although this task presents considerable challenges, the work concentrates on engineering the circuit to minimize mismatch and reflection coefficients, while simultaneously enhancing circuit transconductance. These efforts aim to improve the noise figure as efficiently as possible. The results of this study indicate the possibility of achieving a noise figure of approximately 0.009 dB for a unique circuit design operating at 10 K. In a departure from traditional approaches, this study employs quantum mechanical theory to analyze the circuit comprehensively. By employing quantum theory, the researchers derive relationships that highlight the crucial quantities upon which the circuit design should focus to optimize the noise figure. For example, the circuit's gain power, which depends on the circuit's photonic modes, is theoretically derived and found to affect the noise figure directly. Ultimately, by merging quantum theory with engineering approaches, this study successfully designs a highly efficient circuit that significantly minimizes the noise figure in a quantum application setting.
In this study, we present the design and analysis of a Low Noise Amplifier tailored specifically for quantum applications. We selected the HEMT for its unique noise reduction properties, crucial for quantum engineering. The main goal is to minimize the noise figure within the C-band frequency range (4-8 GHz) to induce nonclassicality in quantum signals. While achieving a noise figure of less than 0.065 dB within this band, we recognized the trade-off with gain, mitigated by incorporating additional stages to maintain noise figure at optimal levels. Quantum analysis of the circuit, employing a simplified model of HEMT due to its complexity, revealed insights into its nonlinear properties and interactions between circuit components and environmental factors. Leveraging Qutip toolbox in Python, we conducted time-evolution analysis of the system, revealing the circuit's behavior as an open quantum system under cryogenic conditions. Our investigation extends to quantifying quantum correlation (quantum discord) and its relationship with noise figure, posing important questions regarding the direct impact of its minimization on circuit nonclassicality at cryogenic temperatures. This comprehensive study sheds light on the intricate interplay between circuit design, and its influence on the relationship between the noise figure and quantum correlation.
A quantum-limited amplifier enables the amplification of weak signals while introducing minimal noise dictated by the principles of quantum mechanics. Such amplifiers serve a broad spectrum of applications in quantum computing, including fast and accurate readout of superconducting qubits and spins, as well as various uses in quantum sensing and metrology. Parametric amplification, primarily developed with use of Josephson junctions, has evolved into the leading technology for highly effective microwave measurements within quantum circuits. Despite their significant contributions, these amplifiers face fundamental limitations, such as their inability to handle high powers, their sensitivity to parasitic magnetic fields, and particularly their limitation to operate only at millikelvin temperatures. To tackle these challenges, here we experimentally develop a novel quantum-limited amplifier based on superconducting kinetic inductance and present an extensive theoretical model to describe this nonlinear coupled-mode system. Our device surpasses the conventional constraints associated with Josephson-junction amplifiers by operating at much higher temperatures up to 4.5 K. With two distinct spectral modes and tunability through bias current, this amplifier can operate selectively in both the single-mode-amplification regime and the double-mode-amplification regime near the quantum noise limit. Using a nonlinear thin film exhibiting kinetic inductance, our device attains gain exceeding 50 dB in a single-mode configuration and 32 dB in a double-mode configuration, while adding 0.82 input-referred noise quanta. Importantly, this amplifier eliminates the need for Josephson junctions, resulting in the capability to handle significantly higher powers than Josephson junction--based amplifiers. It also demonstrates resilience in the presence of magnetic fields, offers a straightforward design, and increases reliability. This positions the amplifier as a versatile solution for quantum applications and facilitates its integration into future superconducting quantum computers.
Abstract This study presents the design and analysis of a specialized RF/MW circuit named the Quantum Non-classicality Enhancing Circuit, specifically developed for quantum applications. The primary objective is to reduce the noise figure within the operational frequency range of 4–8 GHz to enhance non-classical properties in quantum signals. To achieve this, a HEMT was chosen due to its exceptional noise reduction capabilities, which are critical for quantum engineering. While targeting a noise figure of less than 0.065 dB within the specified frequency band, a trade-off with gain was identified. This issue was addressed by introducing additional amplification stages to stabilize the noise figure without compromising overall performance. Quantum analysis of the circuit, based on a simplified HEMT model, provided valuable insights into its nonlinear behavior and the interaction between circuit components and environmental factors. Using the QuTiP toolbox in Python, a time-evolution analysis of the system was conducted, revealing the circuit’s response as an open quantum system under cryogenic conditions. The study also explores the relationship between quantum correlation (measured by quantum discord) and the noise figure, raising significant questions about the impact of noise minimization on enhancing non-classicality at low temperatures. Alongside the quantum analysis, a detailed circuit layout was designed and optimized to minimize the noise figure. The findings from the quantum analysis demonstrated that non-classicality generation and noise minimization share a common foundation, reinforcing the design approach. This comprehensive study highlights the complex interplay between circuit design and quantum properties, offering a strategic path toward improved quantum signal processing at cryogenic temperatures.
Josephson Parametric Amplifiers (JPAs) are key components in quantum information processing due to their ability to amplify weak quantum signals with near-quantum-limited noise performance. This is essential for applications such as qubit readout, quantum sensing, and communication, where signal fidelity and coherence preservation are critical. Unlike CMOS and HEMT amplifiers used in conventional RF systems, JPAs are specifically optimized for millikelvin (mK) cryogenic environments. CMOS amplifiers offer good integration but perform poorly at ultra-low temperatures due to high noise. HEMT amplifiers provide better noise performance but are power-intensive and less suited for mK operation. JPAs, by contrast, combine low power consumption with ultra-low noise and excellent cryogenic compatibility, making them ideal for quantum systems. The first part of this study compares these RF amplifier types and explains why JPAs are preferred in cryogenic quantum applications. The second part focuses on the design and analysis of JPAs based on both single Josephson junctions and junction arrays. While single-junction JPAs utilize nonlinear inductance for amplification, they suffer from gain compression, limited dynamic range, and sensitivity to fabrication variations. To overcome these challenges, this work explores JPA designs using Josephson junction arrays. Arrays distribute the nonlinear response, enhancing power handling, linearity, impedance tunability, and coherence while reducing phase noise. Several advanced JPA architectures are proposed, simulated, and compared using quantum theory and CAD tools to assess performance trade-offs and improvements over conventional designs.
Amplification of weak microwave signals with minimal added noise is of importance to science and technology. Artificial quantum systems, based on superconducting circuits, can now amplify and detect even single microwave photons. However, this requires operating at millikelvin temperatures. Natural quantum systems can also be used for low-noise microwave amplification using stimulated emission effects; however, they generate a higher noise, especially when operating above ~1 K. Here, we demonstrate the use of electron spins in diamond as a quantum microwave amplifier operating with quantum-limited internal noise, even above liquid nitrogen temperatures. We report on the amplifier's design, gain, bandwidth, saturation power, and noise. This capability can lead the way to previously unavailable quantum science, engineering, and physics applications.
The design and development of a cryogenic Ultra-Low-Noise Signal Amplification (ULNA) and detection system for spectroscopy of ultra-cold systems are reported here for the operation in the 0.5 - 4 GHz spectrum of frequencies (the “L” and “S” microwave bands). The design is suitable for weak RF signal detection and spectroscopy from ultra-cold systems confined in cryogenic RF cavities, as entailed in a number of physics, physical chemistry and analytical chemistry applications, such as NMR/NQR/EPR and microwave spectroscopy, Paul traps, Bose-Einstein Condensates (BEC’s) and cavity Quantum Electrodynamics (cQED). Using a generic Low-Noise Amplifier (LNA) architecture for a GaAs enhancement mode High-Electron Mobility FET device, our design has especially been devised for scientific applications where ultra-low-noise amplification systems are sought to amplify and detect weak RF signals under various conditions and environments, including cryogenic temperatures, with the least possible noise susceptibility. The amplifier offers a 16 dB gain and a 0.8 dB noise figure at 2.5 GHz, while operating at room temperature, which can improve significantly at low temperatures. Both dc and RF outputs are provided by the amplifier to integrate it in a closed-loop or continuous-wave spectroscopy system or connect it to a variety of instruments, a factor which is lacking in commercial LNA devices. Following the amplification stage, the RF signal detection is carried out with the help of a post-amplifier and detection system based upon a set of Zero-Bias Schottky Barrier Diodes (ZBD’s) and a high-precision ultra-low noise jFET operational amplifier. The scheme offers unique benefits of sensitive detection and very-low noise amplification for measuring extremely weak on-resonance signals with substantial low- noise response and excellent stability while eliminating complicated and expensive heterodyne schemes. The LNA stage is fully capable to be a part of low-temperature experiments while being operated in cryogenic conditions down to about 500 mK.