Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2108.00879 · npj Quantum Information

Conveyor-mode single-electron shuttling in Si/SiGe for a scalable quantum computing architecture

Inga Seidler, Tom Struck, Ran Xue, Niels Focke, Stefan Trellenkamp, Hendrik Bluhm, Lars R. Schreiber

Published Aug 30, 2022• 118 citations
arXivHTMLPDF

Abstract

Abstract Small spin-qubit registers defined by single electrons confined in Si/SiGe quantum dots operate successfully and connecting these would permit scalable quantum computation. Shuttling the qubit carrying electrons between registers is a natural choice for high-fidelity coherent links provided the overhead of control signals stays moderate. Our proof-of-principle demonstrates shuttling of a single electron by a propagating wave-potential in an electrostatically defined 420 nm long Si/SiGe quantum-channel. This conveyor-mode shuttling approach requires independent from its length only four sinusoidal control signals. We discuss the tuning of the signal parameters, detect the smoothness of the electron motion enabling the mapping of potential disorder and observe a high single-electron shuttling fidelity of 99.42 ± 0.02% including a reversal of direction. Our shuttling device can be readily embedded in industrial fabrication of Si/SiGe qubit chips and paves the way to solving the signal-fanout problem for a fully scalable semiconductor quantum-computing architecture.

DOI
10.1038/s41534-022-00615-2

Related papers

Conveyor-mode electron shuttling through a T-junction in Si/SiGe

Max Beer, Ran Xue, Lennart Deda +6 more

Conveyor-mode shuttling in gated Si/SiGe devices enables adiabatic transfer of single electrons, electron patterns and spin qubits confined in quantum dots across several microns with a scalable number of signal lines. To realize their full potential, linear shuttle lanes must connect into a two-dimensional grid with controllable routing. We introduce a T-junction device linking two independently driven shuttle lanes. Electron routing across the junction requires no extra control lines beyond the four channels per conveyor belt. We measure an inter-lane charge transfer fidelity of $F = 100.0000000^{+0}_{-9\times 10^{-7}}\,\%$ at an instantaneous electron velocity of $270\,\mathrm{mm}\,\mathrm{s}^{-1}$. The filling of 54 quantum dots is controlled by simple atomic pulses, allowing us to swap electron patterns, laying the groundwork for a native spin-qubit SWAP gate. This T-junction establishes a path towards scalable, two-dimensional quantum computing architectures with flexible spin qubit routing for quantum error correction.

cond-mat.mes-hallCross-listedarXiv:2601.03942•Jan 8, 2026

Concepts and prototyping for scalable quantum computing based on conveyor-mode single-electron shuttling

Matthias Künne

Universal quantum computing promises solutions to a wide range of problems of significant scientific and socioeconomic impact that are computationally intractable using classical hardware. Since physical qubits are inherently noisy and prone to decoherence, realizing a sufficient number of logical qubits to unlock practically relevant problem classes will likely require quantum error correction, resulting in an overhead of millions of physical qubits. Among all competing hardware platforms, spin qubits in gate-defined quantum dots are uniquely positioned: single- and two-qubit gate fidelities routinely exceed the error-correction threshold, and the experimentally proven compatibility with industrial-grade semiconductor manufacturing may enable millions of qubits on a single chip. Realizing this potential, however, requires quantum processor architectures that scale to large qubit numbers with two‑dimensional connectivity while maintaining high operational fidelities. Building on the theoretical feasibility of high‑fidelity spin‑coherent electron shuttling, the SpinBus architecture is introduced to enable scaling to application-relevant qubit numbers. The SpinBus architecture leverages the conveyor-mode shuttling device named Quantum Bus (QuBus) for coherent qubit coupling over micron‑scale distances to accommodate, at the level of the quantum processor chip, wiring fan‑out and locally integrated control electronics at cryogenic temperatures. Device simulations for all relevant operations in the Si/SiGe platform validate operation fidelities exceeding 99 % as well as compatibility with the requirements of established semiconductor patterning technology. Control with room‑temperature electronics plausibly supports at least 144 qubits, while substantially larger quantum processor sizes are conceivable using cryogenic control electronics. For the experimental realization of QuBus devices, a novel high‑yield multilayer electron-beam lithography process, which can readily be adapted to different device layouts, was developed to fabricate the required > 100 aligned metallic gate electrodes. Benchmarking with a semiconductor industry‑inspired methodology and inspection of > 100 devices demonstrated 99 % gate fabrication yield and at least 5 nm overlay accuracy. Utilizing GaAs/(Al,Ga)As QuBus prototype devices with a 7 µm shuttling channel for quantized-current experiments validated key criteria for conveyor-mode shuttling, in particular linear current scaling for operation frequencies up to 40 MHz, and provided preliminary evidence consistent with quantized conveyor-mode electron transfer. These results support the viability of conveyor-mode shuttling for qubit coupling and indicate the suitability of QuBus devices for metrological applications.

•Jan 1, 2026•0 citations

Spin-EPR-pair separation by conveyor-mode single electron shuttling in Si/SiGe

Tom Struck, M. Volmer, Lino Visser +7 more

Long-ranged coherent qubit coupling is a missing function block for scaling up spin qubit based quantum computing solutions. Spin-coherent conveyor-mode electron-shuttling could enable spin quantum-chips with scalable and sparse qubit-architecture. Its key feature is the operation by only few easily tuneable input terminals and compatibility with industrial gate-fabrication. Single electron shuttling in conveyor-mode in a 420 nm long quantum bus has been demonstrated previously. Here we investigate the spin coherence during conveyor-mode shuttling by separation and rejoining an Einstein-Podolsky-Rosen (EPR) spin-pair. Compared to previous work we boost the shuttle velocity by a factor of 10000. We observe a rising spin-qubit dephasing time with the longer shuttle distances due to motional narrowing and estimate the spin-shuttle infidelity due to dephasing to be 0.7% for a total shuttle distance of nominal 560 nm. Shuttling several loops up to an accumulated distance of 3.36 μm, spin-entanglement of the EPR pair is still detectable, giving good perspective for our approach of a shuttle-based scalable quantum computing architecture in silicon.

arXiv:2307.04897•Nature Communications•Feb 13, 2024•59 citations

Spin qubit operations by conveyor-mode shuttling

M. De Smet, Y. Matsumoto, D. Fernández-Fernández +8 more

Dynamic qubit routing is emerging as a promising architectural path for semiconductor quantum processors. Charge carriers can be rapidly moved around on a chip using traveling-wave potentials known as conveyors, preserving the spin state with high fidelity. Originally developed for spin transport, conveyor-mode shuttling may also offer opportunities for performing qubit operations directly controlled by the motion itself. Here, we demonstrate coherent single- and two-qubit control by conveyor-mode electron shuttling, using two conceptually different approaches. First, conveyor electric-dipole spin resonance (conveyor EDSR) achieves high-fidelity rotations by resonantly shuttling spins through transverse magnetic-field gradients at their mean Larmor frequency. Second, conveyor diabatic gates exploit quantization-axis tilts for tunable bang-bang control. Combining diabatic conveyor transport with exchange activation controlled by the motion directly yields a variety of effective two-qubit interactions selectable via the shuttling speed and distance. These experimental results motivate an architectural paradigm of reconfigurable and transport-driven spin qubits.

cond-mat.mes-hallCross-listedarXiv:2606.21452•Jun 22, 2026

Numerical simulation of coherent spin-shuttling in a QuBus with charged defects

Nils Ciroth, Arnau Sala, Ran Xue +4 more

Recent advances in coherent conveyor-mode spin qubit shuttling are paving the way for large-scale quantum computing platforms with qubit connectivity achieved by spin qubit shuttles. We developed a simulation tool to investigate numerically the impact of device imperfections on the spin-coherence of conveyor-mode shuttling in Si/SiGe. We simulate the quantum evolution of a mobile electron spin-qubit under the influence of sparse and singly charged point defects placed in the Si/SiGe heterostructure in close proximity to the shuttle lane. We consider different locations of a single charge defect with respect to the center of the shuttle lane, multiple orbital states of the electron in the shuttle with $g$-factor differences between the orbital levels, and orbital relaxation induced by electron-phonon interaction. With this simulation framework, we identify the critical defect density of charged point defects in the heterostructure for conveyor-mode spin qubit shuttle devices and quantify the impact of a single defect on the coherence of a qubit.

cond-mat.mes-hallCross-listedarXiv:2512.03588•Dec 4, 2025

The SpinBus architecture for scaling spin qubits with electron shuttling

Matthias Künne, Alexander Willmes, Max Oberländer +10 more

Quantum processor architectures must enable scaling to large qubit numbers while providing two-dimensional qubit connectivity and exquisite operation fidelities. For microwave-controlled semiconductor spin qubits, dense arrays have made considerable progress, but are still limited in size by wiring fan-out and exhibit significant crosstalk between qubits. To overcome these limitations, we introduce the SpinBus architecture, which uses electron shuttling to connect qubits and features low operating frequencies and enhanced qubit coherence. Device simulations for all relevant operations in the Si/SiGe platform validate the feasibility with established semiconductor patterning technology and operation fidelities exceeding 99.9%. Control using room temperature instruments can plausibly support at least 144 qubits, but much larger numbers are conceivable with cryogenic control circuits. Building on the theoretical feasibility of high-fidelity spin-coherent electron shuttling as key enabling factor, the SpinBus architecture may be the basis for a spin-based quantum processor that meets the scalability requirements for practical quantum computing.

arXiv:2306.16348•Nature Communications•Jun 11, 2024•95 citations
Abstract Small spin-qubit registers defined by single electrons confined in Si/SiGe quantum dots operate successfully and connecting these would permit scalable quantum computation. Shuttling the qubit carrying electrons between registers is a natural choice for high-fidelity coherent links provided the overhead of control signals stays moderate. Our proof-of-principle demonstrates shuttling of a single electron by a propagating wave-potential in an electrostatically defined 420 nm long Si/SiGe quantum-channel. This conveyor-mode shuttling approach requires independent from its length only four sinusoidal control signals. We discuss the tuning of the signal parameters, detect the smoothness of the electron motion enabling the mapping of potential disorder and observe a high single-electron shuttling fidelity of 99.42 ± 0.02% including a reversal of direction. Our shuttling device can be readily embedded in industrial fabrication of Si/SiGe qubit chips and paves the way to solving the signal-fanout problem for a fully scalable semiconductor quantum-computing architecture.
Conveyor-mode shuttling in gated Si/SiGe devices enables adiabatic transfer of single electrons, electron patterns and spin qubits confined in quantum dots across several microns with a scalable number of signal lines. To realize their full potential, linear shuttle lanes must connect into a two-dimensional grid with controllable routing. We introduce a T-junction device linking two independently driven shuttle lanes. Electron routing across the junction requires no extra control lines beyond the four channels per conveyor belt. We measure an inter-lane charge transfer fidelity of F=100.0000000−9×10−7+0 %F = 100.0000000^{+0}_{-9\times 10^{-7}}\,\%F=100.0000000−9×10−7+0​% at an instantaneous electron velocity of 270 mm s−1270\,\mathrm{mm}\,\mathrm{s}^{-1}270mms−1. The filling of 54 quantum dots is controlled by simple atomic pulses, allowing us to swap electron patterns, laying the groundwork for a native spin-qubit SWAP gate. This T-junction establishes a path towards scalable, two-dimensional quantum computing architectures with flexible spin qubit routing for quantum error correction.
Universal quantum computing promises solutions to a wide range of problems of significant scientific and socioeconomic impact that are computationally intractable using classical hardware. Since physical qubits are inherently noisy and prone to decoherence, realizing a sufficient number of logical qubits to unlock practically relevant problem classes will likely require quantum error correction, resulting in an overhead of millions of physical qubits. Among all competing hardware platforms, spin qubits in gate-defined quantum dots are uniquely positioned: single- and two-qubit gate fidelities routinely exceed the error-correction threshold, and the experimentally proven compatibility with industrial-grade semiconductor manufacturing may enable millions of qubits on a single chip. Realizing this potential, however, requires quantum processor architectures that scale to large qubit numbers with two‑dimensional connectivity while maintaining high operational fidelities. Building on the theoretical feasibility of high‑fidelity spin‑coherent electron shuttling, the SpinBus architecture is introduced to enable scaling to application-relevant qubit numbers. The SpinBus architecture leverages the conveyor-mode shuttling device named Quantum Bus (QuBus) for coherent qubit coupling over micron‑scale distances to accommodate, at the level of the quantum processor chip, wiring fan‑out and locally integrated control electronics at cryogenic temperatures. Device simulations for all relevant operations in the Si/SiGe platform validate operation fidelities exceeding 99 % as well as compatibility with the requirements of established semiconductor patterning technology. Control with room‑temperature electronics plausibly supports at least 144 qubits, while substantially larger quantum processor sizes are conceivable using cryogenic control electronics. For the experimental realization of QuBus devices, a novel high‑yield multilayer electron-beam lithography process, which can readily be adapted to different device layouts, was developed to fabricate the required > 100 aligned metallic gate electrodes. Benchmarking with a semiconductor industry‑inspired methodology and inspection of > 100 devices demonstrated 99 % gate fabrication yield and at least 5 nm overlay accuracy. Utilizing GaAs/(Al,Ga)As QuBus prototype devices with a 7 µm shuttling channel for quantized-current experiments validated key criteria for conveyor-mode shuttling, in particular linear current scaling for operation frequencies up to 40 MHz, and provided preliminary evidence consistent with quantized conveyor-mode electron transfer. These results support the viability of conveyor-mode shuttling for qubit coupling and indicate the suitability of QuBus devices for metrological applications.
Long-ranged coherent qubit coupling is a missing function block for scaling up spin qubit based quantum computing solutions. Spin-coherent conveyor-mode electron-shuttling could enable spin quantum-chips with scalable and sparse qubit-architecture. Its key feature is the operation by only few easily tuneable input terminals and compatibility with industrial gate-fabrication. Single electron shuttling in conveyor-mode in a 420 nm long quantum bus has been demonstrated previously. Here we investigate the spin coherence during conveyor-mode shuttling by separation and rejoining an Einstein-Podolsky-Rosen (EPR) spin-pair. Compared to previous work we boost the shuttle velocity by a factor of 10000. We observe a rising spin-qubit dephasing time with the longer shuttle distances due to motional narrowing and estimate the spin-shuttle infidelity due to dephasing to be 0.7% for a total shuttle distance of nominal 560 nm. Shuttling several loops up to an accumulated distance of 3.36 μm, spin-entanglement of the EPR pair is still detectable, giving good perspective for our approach of a shuttle-based scalable quantum computing architecture in silicon.
Dynamic qubit routing is emerging as a promising architectural path for semiconductor quantum processors. Charge carriers can be rapidly moved around on a chip using traveling-wave potentials known as conveyors, preserving the spin state with high fidelity. Originally developed for spin transport, conveyor-mode shuttling may also offer opportunities for performing qubit operations directly controlled by the motion itself. Here, we demonstrate coherent single- and two-qubit control by conveyor-mode electron shuttling, using two conceptually different approaches. First, conveyor electric-dipole spin resonance (conveyor EDSR) achieves high-fidelity rotations by resonantly shuttling spins through transverse magnetic-field gradients at their mean Larmor frequency. Second, conveyor diabatic gates exploit quantization-axis tilts for tunable bang-bang control. Combining diabatic conveyor transport with exchange activation controlled by the motion directly yields a variety of effective two-qubit interactions selectable via the shuttling speed and distance. These experimental results motivate an architectural paradigm of reconfigurable and transport-driven spin qubits.
Recent advances in coherent conveyor-mode spin qubit shuttling are paving the way for large-scale quantum computing platforms with qubit connectivity achieved by spin qubit shuttles. We developed a simulation tool to investigate numerically the impact of device imperfections on the spin-coherence of conveyor-mode shuttling in Si/SiGe. We simulate the quantum evolution of a mobile electron spin-qubit under the influence of sparse and singly charged point defects placed in the Si/SiGe heterostructure in close proximity to the shuttle lane. We consider different locations of a single charge defect with respect to the center of the shuttle lane, multiple orbital states of the electron in the shuttle with ggg-factor differences between the orbital levels, and orbital relaxation induced by electron-phonon interaction. With this simulation framework, we identify the critical defect density of charged point defects in the heterostructure for conveyor-mode spin qubit shuttle devices and quantify the impact of a single defect on the coherence of a qubit.
Quantum processor architectures must enable scaling to large qubit numbers while providing two-dimensional qubit connectivity and exquisite operation fidelities. For microwave-controlled semiconductor spin qubits, dense arrays have made considerable progress, but are still limited in size by wiring fan-out and exhibit significant crosstalk between qubits. To overcome these limitations, we introduce the SpinBus architecture, which uses electron shuttling to connect qubits and features low operating frequencies and enhanced qubit coherence. Device simulations for all relevant operations in the Si/SiGe platform validate the feasibility with established semiconductor patterning technology and operation fidelities exceeding 99.9%. Control using room temperature instruments can plausibly support at least 144 qubits, but much larger numbers are conceivable with cryogenic control circuits. Building on the theoretical feasibility of high-fidelity spin-coherent electron shuttling as key enabling factor, the SpinBus architecture may be the basis for a spin-based quantum processor that meets the scalability requirements for practical quantum computing.