Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:2008.07652 · Physical Review Applied

Merged-Element Transmon

R. Zhao, S. Park, T. Zhao, Mustafa Bal, C.R.H. McRae, J. Long, D.P. Pappas

Published Dec 1, 2020• 72 citations
arXivHTMLPDF

Abstract

Transmon qubits are ubiquitous in the pursuit of quantum computing using superconducting circuits. However, they have some drawbacks that still need to be addressed. Most importantly, the scalability of transmons is limited by the large device footprint needed to reduce the participation of the lossy capacitive parts of the circuit. In this work, we investigate and evaluate losses in an alternative device geometry, namely, the merged-element transmon (mergemon). To this end, we replace the large external shunt capacitor of a traditional transmon with the intrinsic capacitance of a Josephson junction and achieve an approximately 100 times reduction in qubit dimensions. We report the implementation of the mergemon using a sputtered $\mathrm{Nb}$--amorphous-$\mathrm{Si}$--$\mathrm{Nb}$ trilayer film. In an experiment below 10 mK, the frequency of the readout resonator, capacitively coupled to the mergemon, exhibits a qubit-state-dependent shift in the low-power regime. The device also demonstrates the single-photon and multiphoton transitions that represent a weakly anharmonic system in two-tone spectroscopy. The transition spectra are explained well with master-equation simulations. A participation-ratio analysis identifies the dielectric loss of the amorphous-$\mathrm{Si}$ tunnel barrier and its interfaces as the dominant source for qubit relaxation. We expect the mergemon to achieve high coherence for relatively small device dimensions when implemented with a low-loss, epitaxially grown, and lattice-matched trilayer.

DOI
10.1103/physrevapplied.14.064006

Related papers

Merged-Element Transmons: Design and Qubit Performance

H. Jonathon Mamin, Elbert Huang, Santino D. Carnevale +12 more

We demonstrate a superconducting transmon qubit in which a Josephson junction has been engineered to act as its own parallel shunt capacitor. This merged-element transmon potentially offers a smaller footprint than conventional transmons. Because it concentrates the electromagnetic energy inside the junction, it reduces the relative electric field participation from other interfaces. By combining micrometer-scale $\mathrm{Al}$/$\mathrm{Al}\mathrm{O}$${}_{x}$/$\mathrm{Al}$ junctions with long oxidations, we produce functional devices with ${E}_{J}/{E}_{C}$ in the low-transmon regime (${E}_{J}/{E}_{C}\ensuremath{\lesssim}30$). Cryogenic $I$-$V$ measurements show a sharp $dI/dV$ structure with low subgap conduction. Qubit spectroscopy of tunable versions shows a small number of avoided level crossings, suggesting the presence of two-level systems. We observe mean ${T}_{1}$ times typically in the range of $10--90\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$, with some annealed devices exhibiting ${T}_{1}>100\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$ over several hours. The results suggest that energy relaxation in conventional small-junction transmons is not limited by junction loss.

arXiv:2103.09163•Physical Review Applied•Aug 13, 2021•58 citations

Towards merged-element transmons using silicon fins: The FinMET

Aranya Goswami, Anthony McFadden, Tongyu Zhao +7 more

A merged-element transmon (MET) device based on silicon (Si) fins is proposed, and the first steps to form such a “FinMET” are demonstrated. This new application of fin technology capitalizes on the anisotropic etch of Si(111) relative to Si(110) to define atomically flat, high aspect ratio Si tunnel barriers with epitaxial superconductor contacts on parallel sidewall surfaces. This process circumvents the challenges associated with the growth of low-loss insulating barriers on lattice matched superconductors. By implementing low-loss, intrinsic float-zone Si as the barrier material rather than commonly used, potentially lossy AlOx, the FinMET is expected to overcome problems with standard transmons by (1) reducing dielectric losses; (2) minimizing the formation of two-level system spectral features; (3) exhibiting greater control over barrier thickness and qubit frequency spread, especially when combined with commercial fin fabrication and atomic-layer or digital etching; (4) potentially reducing the footprint by several orders of magnitude; and (5) allowing scalable fabrication. Here, as a first step to making such a device, the fabrication of Si fin capacitors on Si(110) substrates with shadow-deposited Al electrodes is demonstrated. These fin capacitors are then fabricated into lumped element resonator circuits and probed using low-temperature microwave measurements. Further thinning of silicon junctions toward the tunneling regime will enable the scalable fabrication of FinMET devices based on existing silicon technology while simultaneously avoiding lossy amorphous dielectrics for the tunnel barriers.

arXiv:2108.11519•Applied Physics Letters•Aug 8, 2022•15 citations

Merged-element transmons on Si fins: the FinMET

Aranya Goswami, Anthony McFadden, Hadass S. Inbar +4 more

A merged-element transmon (MET) device, based on Si fins, is proposed and the steps to form such a are demonstrated. This new application of fin technology capitalizes on the anisotropic etch of Si(111) relative to Si(110) to define atomically flat, high aspect ratio Si tunnel barriers with epitaxial superconductor contacts on the parallel side-wall surfaces. This process circumvents the challenges associated with the growth of low-loss insulating barriers on lattice matched superconductors. By implementing low-loss, intrinsic float-zone Si as the barrier material rather than commonly used, lossy Al2O3, the FinMET is expected to overcome problems with standard transmons by (1) reducing dielectric losses; (2) minimizing the formation of two-level system spectral features; (3) exhibiting greater control over barrier thickness and qubit frequency spread, especially when combined with commercial fin fabrication and atomic-layer digital etching; (4) reducing the footprint by four orders of magnitude; and (5) allowing scalable fabrication. Here, fabrication of Si fins on Si(110) substrates with shadow-deposited Al electrodes is demonstrated. The formation of FinMET devices is expected to allow tunnel junction patterning with optical lithography. This facilitates uniform fabrication on Si wafers based on existing infrastructure for fin-based devices while simultaneously avoiding lossy amorphous dielectrics for tunnel barriers.

•Aug 25, 2021•0 citations

Coherent and compact van der Waals transmon qubits

Jesse Balgley, Jinho Park, Xuanjing Chu +9 more

State-of-the-art superconducting qubits rely on a limited set of thin-film materials. Expanding their materials palette can improve performance, extend operating regimes, and introduce new functionalities, but conventional thin-film fabrication hinders systematic exploration of new material combinations. Van der Waals (vdW) materials offer a highly modular crystalline platform that facilitates such exploration while enabling gate-tunability, higher-temperature operation, and compact qubit geometries. Yet it remains unknown whether a fully vdW superconducting qubit can support quantum coherence and what mechanisms dominate loss at both low and elevated temperatures in such a device. Here we demonstrate quantum-coherent merged-element transmons made entirely from vdW Josephson junctions. These first-generation, fully crystalline qubits achieve microsecond lifetimes in an ultra-compact footprint without external shunt capacitors. Energy relaxation measurements, together with microwave characterization of vdW capacitors, point to dielectric loss as the dominant relaxation channel up to hundreds of millikelvin. These results establish vdW materials as a viable platform for compact superconducting quantum devices.

quant-pharXiv:2512.08059•Dec 10, 2025•7 citations

Coherence in a transmon qubit with epitaxial tunnel junctions

Martin P. Weides, Jeffrey S. Kline, Michael R. Vissers +5 more

We developed transmon qubits based on epitaxial tunnel junctions and interdigitated capacitors. This multileveled qubit, patterned by use of all-optical lithography, is a step towards scalable qubits with a high integration density. The relaxation time T1 is 0.72−0.86 μs and the ensemble dephasing time T2* is slightly larger than T1. The dephasing time T2 (1.36 μs) is nearly energy-relaxation-limited. Qubit spectroscopy yields weaker level splitting than observed in qubits with amorphous barriers in equivalent-size junctions. The qubit’s inferred microwave loss closely matches the weighted losses of the individual elements (junction, wiring dielectric, and interdigitated capacitor), determined by independent resonator measurements.

arXiv:1111.5083•Applied Physics Letters•Dec 26, 2011•53 citations

Transmon qubits coupled to superconducting lumped element resonators

Baladitya Suri

I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlO$_x$/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around $6\,$GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about $150\, \mathrm{nm} \times 150\, \mathrm{nm}$ and with Josephson energy $E_J$ such that $10\,\text{GHz} \leq E_J / h \leq 30\,$GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was $E_c / h \approx 300\,$MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons $\bar{n}$ in the resonator. I also observed a nonlinear variation of $\bar{n}$ with the applied power of the coupler tone $P_{rf}$. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of $5.474\,$GHz photons in the resonator, at an effective temperature of $120\,$mK resulted in a weak $n=1$ thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the $n=1$ thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From $T_1$ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes ($T_1 \sim 1\,\mu$s) limited by strong coupling to the $50\,\Omega$ transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage ($\mathrm{d}f_{Rabi}\, / \mathrm{d}V$) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator $\omega_r/2\pi$ from 5.4$\,$GHz to 7.2$\,$GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor $Q_e$ from 20,000 to 70,000, and reducing the transmon-resonator coupling $g/2\pi$ from 70$\,$MHz to 40$\,$MHz, I reduced the Rabi coupling to the drive by an order of magnitude ($\sim$ factor of 20). The $T_1 \sim 4\,\mu$s of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent $\tan \delta \simeq 5\times10^{-6}$ agree reasonably well with the measured $T_1$ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.

•Jan 1, 2015•3 citations
Transmon qubits are ubiquitous in the pursuit of quantum computing using superconducting circuits. However, they have some drawbacks that still need to be addressed. Most importantly, the scalability of transmons is limited by the large device footprint needed to reduce the participation of the lossy capacitive parts of the circuit. In this work, we investigate and evaluate losses in an alternative device geometry, namely, the merged-element transmon (mergemon). To this end, we replace the large external shunt capacitor of a traditional transmon with the intrinsic capacitance of a Josephson junction and achieve an approximately 100 times reduction in qubit dimensions. We report the implementation of the mergemon using a sputtered Nb\mathrm{Nb}Nb--amorphous-Si\mathrm{Si}Si--Nb\mathrm{Nb}Nb trilayer film. In an experiment below 10 mK, the frequency of the readout resonator, capacitively coupled to the mergemon, exhibits a qubit-state-dependent shift in the low-power regime. The device also demonstrates the single-photon and multiphoton transitions that represent a weakly anharmonic system in two-tone spectroscopy. The transition spectra are explained well with master-equation simulations. A participation-ratio analysis identifies the dielectric loss of the amorphous-Si\mathrm{Si}Si tunnel barrier and its interfaces as the dominant source for qubit relaxation. We expect the mergemon to achieve high coherence for relatively small device dimensions when implemented with a low-loss, epitaxially grown, and lattice-matched trilayer.
We demonstrate a superconducting transmon qubit in which a Josephson junction has been engineered to act as its own parallel shunt capacitor. This merged-element transmon potentially offers a smaller footprint than conventional transmons. Because it concentrates the electromagnetic energy inside the junction, it reduces the relative electric field participation from other interfaces. By combining micrometer-scale Al\mathrm{Al}Al/AlO\mathrm{Al}\mathrm{O}AlOx{}_{x}x​/Al\mathrm{Al}Al junctions with long oxidations, we produce functional devices with EJ/EC{E}_{J}/{E}_{C}EJ​/EC​ in the low-transmon regime (${E}_{J}/{E}_{C}\ensuremath{\lesssim}30$). Cryogenic III-VVV measurements show a sharp dI/dVdI/dVdI/dV structure with low subgap conduction. Qubit spectroscopy of tunable versions shows a small number of avoided level crossings, suggesting the presence of two-level systems. We observe mean T1{T}_{1}T1​ times typically in the range of $10--90\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$, with some annealed devices exhibiting ${T}_{1}>100\phantom{\rule{0.2em}{0ex}}\ensuremath{\mu}\mathrm{s}$ over several hours. The results suggest that energy relaxation in conventional small-junction transmons is not limited by junction loss.
A merged-element transmon (MET) device based on silicon (Si) fins is proposed, and the first steps to form such a “FinMET” are demonstrated. This new application of fin technology capitalizes on the anisotropic etch of Si(111) relative to Si(110) to define atomically flat, high aspect ratio Si tunnel barriers with epitaxial superconductor contacts on parallel sidewall surfaces. This process circumvents the challenges associated with the growth of low-loss insulating barriers on lattice matched superconductors. By implementing low-loss, intrinsic float-zone Si as the barrier material rather than commonly used, potentially lossy AlOx, the FinMET is expected to overcome problems with standard transmons by (1) reducing dielectric losses; (2) minimizing the formation of two-level system spectral features; (3) exhibiting greater control over barrier thickness and qubit frequency spread, especially when combined with commercial fin fabrication and atomic-layer or digital etching; (4) potentially reducing the footprint by several orders of magnitude; and (5) allowing scalable fabrication. Here, as a first step to making such a device, the fabrication of Si fin capacitors on Si(110) substrates with shadow-deposited Al electrodes is demonstrated. These fin capacitors are then fabricated into lumped element resonator circuits and probed using low-temperature microwave measurements. Further thinning of silicon junctions toward the tunneling regime will enable the scalable fabrication of FinMET devices based on existing silicon technology while simultaneously avoiding lossy amorphous dielectrics for the tunnel barriers.
A merged-element transmon (MET) device, based on Si fins, is proposed and the steps to form such a are demonstrated. This new application of fin technology capitalizes on the anisotropic etch of Si(111) relative to Si(110) to define atomically flat, high aspect ratio Si tunnel barriers with epitaxial superconductor contacts on the parallel side-wall surfaces. This process circumvents the challenges associated with the growth of low-loss insulating barriers on lattice matched superconductors. By implementing low-loss, intrinsic float-zone Si as the barrier material rather than commonly used, lossy Al2O3, the FinMET is expected to overcome problems with standard transmons by (1) reducing dielectric losses; (2) minimizing the formation of two-level system spectral features; (3) exhibiting greater control over barrier thickness and qubit frequency spread, especially when combined with commercial fin fabrication and atomic-layer digital etching; (4) reducing the footprint by four orders of magnitude; and (5) allowing scalable fabrication. Here, fabrication of Si fins on Si(110) substrates with shadow-deposited Al electrodes is demonstrated. The formation of FinMET devices is expected to allow tunnel junction patterning with optical lithography. This facilitates uniform fabrication on Si wafers based on existing infrastructure for fin-based devices while simultaneously avoiding lossy amorphous dielectrics for tunnel barriers.
State-of-the-art superconducting qubits rely on a limited set of thin-film materials. Expanding their materials palette can improve performance, extend operating regimes, and introduce new functionalities, but conventional thin-film fabrication hinders systematic exploration of new material combinations. Van der Waals (vdW) materials offer a highly modular crystalline platform that facilitates such exploration while enabling gate-tunability, higher-temperature operation, and compact qubit geometries. Yet it remains unknown whether a fully vdW superconducting qubit can support quantum coherence and what mechanisms dominate loss at both low and elevated temperatures in such a device. Here we demonstrate quantum-coherent merged-element transmons made entirely from vdW Josephson junctions. These first-generation, fully crystalline qubits achieve microsecond lifetimes in an ultra-compact footprint without external shunt capacitors. Energy relaxation measurements, together with microwave characterization of vdW capacitors, point to dielectric loss as the dominant relaxation channel up to hundreds of millikelvin. These results establish vdW materials as a viable platform for compact superconducting quantum devices.
We developed transmon qubits based on epitaxial tunnel junctions and interdigitated capacitors. This multileveled qubit, patterned by use of all-optical lithography, is a step towards scalable qubits with a high integration density. The relaxation time T1 is 0.72−0.86 μs and the ensemble dephasing time T2* is slightly larger than T1. The dephasing time T2 (1.36 μs) is nearly energy-relaxation-limited. Qubit spectroscopy yields weaker level splitting than observed in qubits with amorphous barriers in equivalent-size junctions. The qubit’s inferred microwave loss closely matches the weighted losses of the individual elements (junction, wiring dielectric, and interdigitated capacitor), determined by independent resonator measurements.
I discuss the design, fabrication and measurement at millikelvin-temperatures of Al/AlOx_xx​/Al Josephson junction-based transmon qubits coupled to superconducting thin-film lumped element microwave resonators made of aluminum on sapphire. The resonators had a center frequency of around 6 6\,6GHz, and a total quality factor ranging from 15,000 to 70,000 for the various devices. The area of the transmon junctions was about 150 nm×150 nm150\, \mathrm{nm} \times 150\, \mathrm{nm}150nm×150nm and with Josephson energy EJE_JEJ​ such that 10 GHz≤EJ/h≤30 10\,\text{GHz} \leq E_J / h \leq 30\,10GHz≤EJ​/h≤30GHz. The charging energy of the transmons arising mostly from the large interdigital shunt capacitance, was Ec/h≈300 E_c / h \approx 300\,Ec​/h≈300MHz. I present microwave spectroscopy of the devices in the strongly dispersive regime of circuit quantum electrodynamics. In this limit the ac Stark shift due to a single photon in the resonator is greater than the linewidth of the qubit transition. When the resonator is driven coherently using a coupler tone, the transmon spectrum reveals individual ``photon number'' peaks, each corresponding to a single additional photon in the resonator. Using a weighted average of the peak heights in the qubit spectrum, I calculated the average number of photons nˉ\bar{n}nˉ in the resonator. I also observed a nonlinear variation of nˉ\bar{n}nˉ with the applied power of the coupler tone PrfP_{rf}Prf​. I studied this nonlinearity using numerical simulations and found good qualitative agreement with data. In the absence of a coherent drive on the resonator, a thermal population of 5.474 5.474\,5.474GHz photons in the resonator, at an effective temperature of 120 120\,120mK resulted in a weak n=1n=1n=1 thermal photon peak in the qubit spectrum. In the presence of independent coupler and probe tones, the n=1n=1n=1 thermal photon peak revealed an Autler-Townes splitting. The observed effect was explained accurately using the four lowest levels of the dispersively dressed Jaynes-Cummings transmon-resonator system, and numerical simulations of the steady-state master equation for the coupled system. I also present time-domain measurements on transmons coupled to lumped-element resonators. From T1T_1T1​ and Rabi oscillation measurements, I found that my early transmon devices (called design LEv5) had lifetimes (T1∼1 μT_1 \sim 1\,\muT1​∼1μs) limited by strong coupling to the 50 Ω50\,\Omega50Ω transmission line. This coupling was characterized by the the rate of change of the Rabi oscillation frequency with the change in the drive voltage (dfRabi /dV\mathrm{d}f_{Rabi}\, / \mathrm{d}VdfRabi​/dV) -- also termed the Rabi coupling to the drive. I studied the design of the transmon-resonator system using circuit analysis and microwave simulations with the aim being to reduce the Rabi coupling to the drive. By increasing the resonance frequency of the resonator ωr/2π\omega_r/2\piωr​/2π from 5.4 \,GHz to 7.2 \,GHz, lowering the coupling of the resonator to the transmission line and thereby increasing the external quality factor QeQ_eQe​ from 20,000 to 70,000, and reducing the transmon-resonator coupling g/2πg/2\pig/2π from 70 \,MHz to 40 \,MHz, I reduced the Rabi coupling to the drive by an order of magnitude (∼\sim∼ factor of 20). The T1∼4 μT_1 \sim 4\,\muT1​∼4μs of devices in the new design (LEv6) was longer than that of the early devices, but still much shorter than the lifetimes predicted from Rabi coupling, suggesting the presence of alternative sources of noise causing qubit relaxation. Microwave simulations and circuit analysis in the presence of a dielectric loss tangent tan⁡δ≃5×10−6\tan \delta \simeq 5\times10^{-6}tanδ≃5×10−6 agree reasonably well with the measured T1T_1T1​ values, suggesting that surface dielectric loss may be causing relaxation of transmons in the new designs.