Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1911.04880 · Optics Express

Single-channel electronic readout of a multipixel superconducting nanowire single photon detector

Johannes Tiedau, Timon Schapeler, Vikas Anant, Helmut Fedder, Christine Silberhorn, Tim J. Bartley

Published Jan 10, 2020• 16 citations
arXivHTMLPDF

Abstract

We present a time-over-threshold readout technique to count the number of activated pixels from an array of superconducting nanowire single photon detectors (SNSPDs). This technique places no additional heatload on the cryostat, and retains the intrinsic count rate of the time-tagger. We demonstrate proof-of-principle operation with respect to a four-pixel device. Furthermore, we show that, given some permissible error threshold, the number of pixels that can be reliably read out scales linearly with the intrinsic signal-to-noise ratio of the individual pixel response.

DOI
10.1364/oe.383111

Related papers

Operation of Superconducting Nanowire Single-Photon Detectors Embedded in Lumped-Element Resonant Circuits

Steffen Doerner, Artem A. Kuzmin, S. Wünsch +2 more

We propose a new operation principle for superconducting nanowire single-photon detectors (SNSPDs) enabling an efficient frequency-division multiplexing of the bias and readout signals of a large multipixel detector array. The SNSPD is part of a resonant circuit, and the microwave signal inside the device is used to bias the detector close to the critical state. Hence, an n×m pixel SNSPD array requires only two coaxial cables from room temperature to the detector ambient temperature of 4.2 K. We show the microwave characterization and single-photon response of such devices and compare the detector efficiencies with conventional dc-biased SNSPDs. Furthermore, we demonstrate the feasibility of array applications with the new operation mode in a two-pixel proof-of-principle device.

IEEE Transactions on Applied Superconductivity•Feb 5, 2016•19 citations

Superconducting nanowire single-photon detector array with pixel-level photon-number resolution

Chenrui Wang, Chaomeng Ding, Jingxue Chen +6 more

We report a 16-pixel (4×4) superconducting nanowire single-photon detector (SNSPD) array featuring pixel-level photon-number-resolving capability. This multidimensional sensing is enabled by integrating a compact four-element series nanowire architecture into each spatial pixel, allowing direct discrimination of one to four photons. Under single-mode fiber illumination, the device achieves a total system detection efficiency of 41.5%, given the array geometrical fill factor of 53%. Across all channels, the device exhibits reliable multiphoton discrimination, maintaining minimum readout fidelities of 96%, 89%, 73%, and 77% for one- to four-photon states, respectively. Furthermore, independent channel evaluations reveal low timing jitter and negligible inter-channel crosstalk (<0.1 % ). By implementing differentiating pulse shaping for high-flux operation, a maximum single-channel −3 dB count rate of 984 MHz is achieved, establishing an aggregated array bandwidth potential of 8.9 GHz. This sensing architecture may provide a viable pathway toward high-flux single-photon imaging, offering potential applications in quantum optics and light detection and ranging (LiDAR) systems.

Photonics Research•Aug 28, 2026•0 citations

Operation of Multipixel Radio-Frequency Superconducting Nanowire Single-Photon Detector Arrays

Steffen Doerner, Artem Kuzmin, S. Wünsch +2 more

The concept of the radio-frequency superconducting nanowire single-photon detector (RF-SNSPD) allows frequency-division multiplexing of the bias and readout lines of several SNSPDs. Using this method, a multi-pixel array can be operated by only one feed line. Consequently, the system complexity as well as the heat load is significantly reduced. To allocate many pixels into a small bandwidth the quality factor of each device is crucial. In this paper, we present an improved RF-SNSPD design. This new design enables a simple tuning of the quality factor as well as the resonant frequency. With a two-pixel device we have demonstrated the operation without crosstalk between the detectors and showed the time, spatial, and photon number resolution. Thereby a single pixel requires only a bandwidth of 14 MHz.

arXiv:1612.02228•IEEE Transactions on Applied Superconductivity•Dec 9, 2016•9 citations

Optical bias and cryogenic laser readout of a multipixel superconducting nanowire single photon detector

Frederik Thiele, Niklas Lamberty, Thomas Hummel +1 more

Cryogenic opto-electronic interconnects are gaining increasing interest as a means to control and readout cryogenic electronic components. The challenge is to achieve sufficient signal integrity with low heat load processing. In this context, we demonstrate the opto-electronic bias and readout of a commercial four-pixel superconducting nanowire single-photon detector array using a cryogenic photodiode and laser. We show that this approach has a similar system detection efficiency to a conventional bias. Furthermore, multi-pixel detection events are faithfully converted between the optical and electrical domains, which allows reliable extraction of amplitude multiplexed photon statistics. Our device has a latent heat load of 2.6 mW, maintains a signal rise time of 3 ns, and operates in free-running (self-resetting) mode at a repetition rate of 600 kHz. This demonstrates the potential of high-bandwidth, low noise, and low heat load opto-electronic interconnects for scalable cryogenic signal processing and transmission.

arXiv:2403.14276•APL Photonics•Jul 1, 2024•7 citations

Enhanced Detection Rate and High Photon-Number Efficiencies with a Scalable Parallel SNSPD

Lorenzo Stasi, Towsif Taher, Giovanni V. Resta +3 more

Since their inception, superconducting nanowire single-photon detectors have been enabling quantum optical applications and the rise of the photonic quantum industry. The evolution in the detector design and read-out strategies has led to the introduction of devices with a plurality of independent pixels, which have been able to operate with high system detection efficiency at high speed while also supporting photon number resolution capabilities. However, this comes at the cost of a complex readout that requires one coaxial cable for each pixel of the array. Here, we report a 28-pixel SNSPD with a dedicated parallel architecture that, while maintaining a simple readout with a single coaxial line, enables the detector to operate at high speed with low-performance degradation. The device shows a maximum single-photon efficiency of 88% and is able to maintain its efficiency above 50%, coupled with a timing jitter lower than 80 ps, up to a detection rate of 200 million counts per second. The detector also provides state-of-the-art photon-number-resolving performances with a 2-photon efficiency of 75% and a 3-photon efficiency of 62%.

arXiv:2406.15312•ACS Photonics•Dec 17, 2024•33 citations

Technologies for superconducting nanowire single-photon detector array system

Shigehito Miki, Taro Yamashita, Hirotaka Terai +2 more

We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Jun 3, 2013•1 citation
We present a time-over-threshold readout technique to count the number of activated pixels from an array of superconducting nanowire single photon detectors (SNSPDs). This technique places no additional heatload on the cryostat, and retains the intrinsic count rate of the time-tagger. We demonstrate proof-of-principle operation with respect to a four-pixel device. Furthermore, we show that, given some permissible error threshold, the number of pixels that can be reliably read out scales linearly with the intrinsic signal-to-noise ratio of the individual pixel response.
We propose a new operation principle for superconducting nanowire single-photon detectors (SNSPDs) enabling an efficient frequency-division multiplexing of the bias and readout signals of a large multipixel detector array. The SNSPD is part of a resonant circuit, and the microwave signal inside the device is used to bias the detector close to the critical state. Hence, an n×m pixel SNSPD array requires only two coaxial cables from room temperature to the detector ambient temperature of 4.2 K. We show the microwave characterization and single-photon response of such devices and compare the detector efficiencies with conventional dc-biased SNSPDs. Furthermore, we demonstrate the feasibility of array applications with the new operation mode in a two-pixel proof-of-principle device.
We report a 16-pixel (4×4) superconducting nanowire single-photon detector (SNSPD) array featuring pixel-level photon-number-resolving capability. This multidimensional sensing is enabled by integrating a compact four-element series nanowire architecture into each spatial pixel, allowing direct discrimination of one to four photons. Under single-mode fiber illumination, the device achieves a total system detection efficiency of 41.5%, given the array geometrical fill factor of 53%. Across all channels, the device exhibits reliable multiphoton discrimination, maintaining minimum readout fidelities of 96%, 89%, 73%, and 77% for one- to four-photon states, respectively. Furthermore, independent channel evaluations reveal low timing jitter and negligible inter-channel crosstalk (<0.1 % ). By implementing differentiating pulse shaping for high-flux operation, a maximum single-channel −3 dB count rate of 984 MHz is achieved, establishing an aggregated array bandwidth potential of 8.9 GHz. This sensing architecture may provide a viable pathway toward high-flux single-photon imaging, offering potential applications in quantum optics and light detection and ranging (LiDAR) systems.
The concept of the radio-frequency superconducting nanowire single-photon detector (RF-SNSPD) allows frequency-division multiplexing of the bias and readout lines of several SNSPDs. Using this method, a multi-pixel array can be operated by only one feed line. Consequently, the system complexity as well as the heat load is significantly reduced. To allocate many pixels into a small bandwidth the quality factor of each device is crucial. In this paper, we present an improved RF-SNSPD design. This new design enables a simple tuning of the quality factor as well as the resonant frequency. With a two-pixel device we have demonstrated the operation without crosstalk between the detectors and showed the time, spatial, and photon number resolution. Thereby a single pixel requires only a bandwidth of 14 MHz.
Cryogenic opto-electronic interconnects are gaining increasing interest as a means to control and readout cryogenic electronic components. The challenge is to achieve sufficient signal integrity with low heat load processing. In this context, we demonstrate the opto-electronic bias and readout of a commercial four-pixel superconducting nanowire single-photon detector array using a cryogenic photodiode and laser. We show that this approach has a similar system detection efficiency to a conventional bias. Furthermore, multi-pixel detection events are faithfully converted between the optical and electrical domains, which allows reliable extraction of amplitude multiplexed photon statistics. Our device has a latent heat load of 2.6 mW, maintains a signal rise time of 3 ns, and operates in free-running (self-resetting) mode at a repetition rate of 600 kHz. This demonstrates the potential of high-bandwidth, low noise, and low heat load opto-electronic interconnects for scalable cryogenic signal processing and transmission.
Since their inception, superconducting nanowire single-photon detectors have been enabling quantum optical applications and the rise of the photonic quantum industry. The evolution in the detector design and read-out strategies has led to the introduction of devices with a plurality of independent pixels, which have been able to operate with high system detection efficiency at high speed while also supporting photon number resolution capabilities. However, this comes at the cost of a complex readout that requires one coaxial cable for each pixel of the array. Here, we report a 28-pixel SNSPD with a dedicated parallel architecture that, while maintaining a simple readout with a single coaxial line, enables the detector to operate at high speed with low-performance degradation. The device shows a maximum single-photon efficiency of 88% and is able to maintain its efficiency above 50%, coupled with a timing jitter lower than 80 ps, up to a detection rate of 200 million counts per second. The detector also provides state-of-the-art photon-number-resolving performances with a 2-photon efficiency of 75% and a 3-photon efficiency of 62%.
We present the development of key technologies for realization of superconducting nanowire single photon detector array system, which enables high counting rates, and allow spatial and pseudo photon number resolution. Toward the realization of practical large-scale SSPD array system, primary issue is how to avoid heat flow into cryocooler system. One of the challenging tasks is the development of their readout electronics. In the conventional readout technique used for single pixel devices, the number of high-frequency coaxial cables increases proportionally with the number of arrays. This causes a significant increase in the heat load from room temperature, which makes the implementation of the SSPD arrays in a compact refrigerator difficult. To overcome this problem, we proposed applying readout electronics with superconducting single-flux-quantum (SFQ) logic circuitsWe show the implementation and successful operation of four pixels SSPD array connected to SFQ readout electronics with parallel bias scheme in a 0.1W GM cryocooler system.