Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1907.00562 · Applied Physics Letters

Fast raster scan multiplexed charge stability measurements toward high-throughput quantum dot array calibration

Wonjin Jang, Min-Kyun Cho, Myungwon Lee, Changki Hong, Jehyun Kim, Hwanchul Jung, Yunchul Chung, V. Umansky, Dohun Kim

Published Jun 17, 2019• 2 citations
arXivHTMLPDF

Abstract

We report raster scan multiplexed charge-stability diagram measurements for tuning multiple gate-defined quantum dots in GaAs/AlGaAs heterostructures. We evaluate the charge sensitivity of the quantum point contact (QPC) in both radio frequency (rf)-reflectometry and direct current-transport modes, where we measure the signal-to-noise ratio (SNR) of 40 for rf-QPC with an integration time per pixel of 10 ms, corresponding to 1.14 ms for resolving single electron transition in the few electron regime. The high SNR for reasonable integration time allows fast two-dimensional (2D) scanning, which we use to facilitate double and triple quantum dot (TQD) tuning processes. We configure a highly stable raster scan multiplexed quantum dot tuning platform using a switching matrix and transformer-coupled alternating current ramp sources with software control. As an example of high-throughput multiple quantum dot tuning, we demonstrate systematic TQD formation using this platform in which a multiplexed combination of 2D scans enables the identification of the few electron regime in multiple quantum dots in just a few minutes. The method presented here is general, and we expect that the tuning platform is applicable to more complex multiple quantum dot arrays, allowing efficient quantum dot system Hamiltonian parameter calibration.

DOI
10.1063/1.5093685

Related papers

Towards autonomous time-calibration of large quantum-dot devices: Detection, real-time feedback, and noise spectroscopy

Anantha S. Rao, Barnaby van Straaten, Valentin John +8 more

The performance and scalability of semiconductor quantum-dot (QD) qubits are limited by electrostatic drift and charge noise that shift operating points and destabilize qubit parameters. As systems expand to large one- and two-dimensional arrays, manual recalibration becomes impractical, creating a need for autonomous stabilization frameworks. Here, we introduce a method that uses the full network of charge-transition lines in repeatedly acquired double-quantum-dot charge stability diagrams (CSDs) as a multidimensional probe of the local electrostatic environment. By accurately tracking the motion of selected transitions in time, we detect voltage drifts, identify abrupt charge reconfigurations, and apply compensating updates to maintain stable operating conditions. We demonstrate our approach on a 10-QD device, showing robust stabilization and real-time diagnostic access to dot-specific noise processes. The high acquisition rate of radio-frequency reflectometry CSD measurements also enables time-domain noise spectroscopy, allowing the extraction of noise power spectral densities, the identification of two-level fluctuators, and the analysis of spatial noise correlations across the array. From our analysis, we find that the background noise at 100~$μ$\si{\hertz} is dominated by drift with a power law of $1/f^2$, accompanied by a few dominant two-level fluctuators and an average linear correlation length of $(188 \pm 38)$~\si{\nano\meter} in the device. These capabilities form the basis of a scalable, autonomous calibration and characterization module for QD-based quantum processors, providing essential feedback for long-duration, high-fidelity qubit operations.

cond-mat.mes-hallCross-listedarXiv:2512.24894•Jan 1, 2026•2 citations

Fast single-charge sensing with a rf quantum point contact

D. J. Reilly, Charles M. Marcus, Micah P. Hanson +1 more

We report high-bandwidth charge sensing measurements using a GaAs quantum point contact embedded in a radio frequency impedance matching circuit (rf-QPC). With the rf-QPC biased near pinch-off where it is most sensitive to charge, we demonstrate a conductance sensitivity of 5×10−6e2∕hHz−1∕2 with a bandwidth of 8MHz. Single-shot readout of a proximal few-electron double quantum dot is investigated in a mode where the rf-QPC back action is rapidly switched.

arXiv:0707.2946•Applied Physics Letters•Oct 15, 2007•299 citations

Scalable Control and Measurement of Gate-Defined Quantum Dot Systems

James Colless

There is currently a worldwide effort towards the realisation of large-scale quantum computers that exploit quantum phenomena for information processing. While these computing systems could potentially redefine the technological landscape, harnessing quantum effects is challenging due to their inherently fragile nature and the experimentally demanding environments in which they arise. In order for quantum computation to be viable it is first necessary to demonstrate the operation of two-level quantum systems (qubits) which have long coherence times, can be quickly read out, and can be controlled with high fidelity. Focusing on these key requirements, this thesis presents four experiments towards scalable solid state quantum computing using gate-defined quantum dot devices based on gallium arsenide (GaAs) heterostructures. The first experiment investigates a phonon emission process that limits the charge coherence in GaAs and potentially complicates the microwave control of multi-qubit devices. We show that this microwave analogy to Raman spectroscopy can provide a means of detecting the unique phonon spectral density created by a nanoscale device. Experimental results are compared to a theoretical model based on a non-Markovian master equation and approaches to suppressing electron-phonon coupling are discussed. The second experiment demonstrates a technique involving in-situ gate electrodes coupled to lumped-element resonators to provide high-bandwidth dispersive read-out of the state of a double quantum dot. We characterise the charge sensitivity of this method in the few-electron regime and benchmark its performance against quantum point contact charge sensors. The third experiment implements a low-loss, chip-level frequency multiplexing scheme for the readout of scaled-up spin qubit arrays. Dispersive gate-sensing is realised in combination with charge detection based on two radio frequency quantum point contacts to perform multiplexed readout of a double quantum dot in the few-electron regime. Demonstration of a 10-channel multiplexing device is achieved and limitations in scaling spin qubit readout to large numbers using multiplexed channels discussed. The final experiment ties previously presented results together by realising a micro-architecture for controlling and reading out qubits during the execution of a quantum algorithm. The basic principles of this architecture are demonstrated via the manipulation of a semiconductor qubit using control pulses that are cryogenically routed using a high-electron mobility transistor switching matrix controlled by a field programmable gate array. Finally, several technical results are also presented including the development of printed circuit board solutions to allow the high-frequency measurement of nanoscale devices at cryogenic temperatures and the design of on-chip interconnects used to suppress electromagnetic crosstalk in high-density spin qubit device architectures.

•Oct 10, 2016•0 citations

Single shot charge detection using a radio-frequency quantum point contact

Maja C. Cassidy, Andrew S. Dzurak, R. G. Clark +4 more

We report on charge sensing measurements of a GaAs semiconductor quantum dot device using a radio frequency quantum point contact (rf-QPC). The rf-QPC is fully characterized at 4K and millikelvin temperatures and found to have a bandwidth exceeding 20MHz. For single shot charge sensing, we achieve a charge sensitivity of ∼2×10−4e∕Hz referred to the neighboring dot’s charge. The rf-QPC compares favorably with rf single electron transistor electrometers and promises to be an extremely useful tool for characterizing and measuring semiconductor quantum systems on fast time scales.

arXiv:0907.1010•Applied Physics Letters•Nov 26, 2007•89 citations

Computer-automated tuning procedures for semiconductor quantum dot arrays

A. R. Mills, M. M. Feldman, C. Monical +4 more

As with any quantum computing platform, semiconductor quantum dot devices require sophisticated hardware and controls for operation. The increasing complexity of quantum dot devices necessitates the advancement of automated control software and image recognition techniques for rapidly evaluating charge stability diagrams. We use an image analysis toolbox developed in Python to automate the calibration of virtual gates, a process that previously involved a large amount of user intervention. Moreover, we show that straightforward feedback protocols can be used to simultaneously tune multiple tunnel couplings in a triple quantum dot in a computer automated fashion. Finally, we adopt the use of a “tunnel coupling lever arm” to model the interdot barrier gate response and discuss how it can be used to more rapidly tune interdot tunnel couplings to the gigahertz values that are compatible with exchange gates.

arXiv:1907.10775•Applied Physics Letters•Sep 9, 2019•67 citations

Combining multiplexed gate-based readout and isolated CMOS quantum dot arrays

Pierre Hamonic, Martin Nurizzo, Jayshankar Nath +15 more

Semiconductor quantum dot arrays are a promising platform to perform spin-based error-corrected quantum computation with large numbers of qubits. However, due to the diverging number of possible charge configurations combined with the limited sensitivity of large-footprint charge sensors, achieving single-spin occupancy in each dot in a growing quantum dot array is exceedingly complex. Therefore, to scale-up a spin-based architecture we must change how individual charges are readout and controlled. Here, we demonstrate single-spin occupancy of each dot in a foundry-fabricated array by combining two methods. 1/ Loading a finite number of electrons into the quantum dot array; simplifying electrostatic tuning by isolating the array from the reservoirs. 2/ Deploying multiplex gate-based reflectometry to dispersively probe charge tunneling and spin states without charge sensors or reservoirs. Our isolated arrays probed by embedded multiplex readout can be readily electrostatically tuned. They are thus a viable, scalable approach for spin-based quantum architectures. Large-footprint, low-sensitivity charge sensors hinder scaling semiconductor quantum dot arrays for quantum computation. Here the authors present a potentially scalable approach using multiplexed gate-based readout and operation in a foundry-fabricated quantum dot array, demonstrating single-electron occupancy.

arXiv:2410.02325•Nature Communications•Jul 9, 2025•7 citations
We report raster scan multiplexed charge-stability diagram measurements for tuning multiple gate-defined quantum dots in GaAs/AlGaAs heterostructures. We evaluate the charge sensitivity of the quantum point contact (QPC) in both radio frequency (rf)-reflectometry and direct current-transport modes, where we measure the signal-to-noise ratio (SNR) of 40 for rf-QPC with an integration time per pixel of 10 ms, corresponding to 1.14 ms for resolving single electron transition in the few electron regime. The high SNR for reasonable integration time allows fast two-dimensional (2D) scanning, which we use to facilitate double and triple quantum dot (TQD) tuning processes. We configure a highly stable raster scan multiplexed quantum dot tuning platform using a switching matrix and transformer-coupled alternating current ramp sources with software control. As an example of high-throughput multiple quantum dot tuning, we demonstrate systematic TQD formation using this platform in which a multiplexed combination of 2D scans enables the identification of the few electron regime in multiple quantum dots in just a few minutes. The method presented here is general, and we expect that the tuning platform is applicable to more complex multiple quantum dot arrays, allowing efficient quantum dot system Hamiltonian parameter calibration.
The performance and scalability of semiconductor quantum-dot (QD) qubits are limited by electrostatic drift and charge noise that shift operating points and destabilize qubit parameters. As systems expand to large one- and two-dimensional arrays, manual recalibration becomes impractical, creating a need for autonomous stabilization frameworks. Here, we introduce a method that uses the full network of charge-transition lines in repeatedly acquired double-quantum-dot charge stability diagrams (CSDs) as a multidimensional probe of the local electrostatic environment. By accurately tracking the motion of selected transitions in time, we detect voltage drifts, identify abrupt charge reconfigurations, and apply compensating updates to maintain stable operating conditions. We demonstrate our approach on a 10-QD device, showing robust stabilization and real-time diagnostic access to dot-specific noise processes. The high acquisition rate of radio-frequency reflectometry CSD measurements also enables time-domain noise spectroscopy, allowing the extraction of noise power spectral densities, the identification of two-level fluctuators, and the analysis of spatial noise correlations across the array. From our analysis, we find that the background noise at 100~μμμ\si{\hertz} is dominated by drift with a power law of 1/f21/f^21/f2, accompanied by a few dominant two-level fluctuators and an average linear correlation length of (188±38)(188 \pm 38)(188±38)~\si{\nano\meter} in the device. These capabilities form the basis of a scalable, autonomous calibration and characterization module for QD-based quantum processors, providing essential feedback for long-duration, high-fidelity qubit operations.
There is currently a worldwide effort towards the realisation of large-scale quantum computers that exploit quantum phenomena for information processing. While these computing systems could potentially redefine the technological landscape, harnessing quantum effects is challenging due to their inherently fragile nature and the experimentally demanding environments in which they arise. In order for quantum computation to be viable it is first necessary to demonstrate the operation of two-level quantum systems (qubits) which have long coherence times, can be quickly read out, and can be controlled with high fidelity. Focusing on these key requirements, this thesis presents four experiments towards scalable solid state quantum computing using gate-defined quantum dot devices based on gallium arsenide (GaAs) heterostructures. The first experiment investigates a phonon emission process that limits the charge coherence in GaAs and potentially complicates the microwave control of multi-qubit devices. We show that this microwave analogy to Raman spectroscopy can provide a means of detecting the unique phonon spectral density created by a nanoscale device. Experimental results are compared to a theoretical model based on a non-Markovian master equation and approaches to suppressing electron-phonon coupling are discussed. The second experiment demonstrates a technique involving in-situ gate electrodes coupled to lumped-element resonators to provide high-bandwidth dispersive read-out of the state of a double quantum dot. We characterise the charge sensitivity of this method in the few-electron regime and benchmark its performance against quantum point contact charge sensors. The third experiment implements a low-loss, chip-level frequency multiplexing scheme for the readout of scaled-up spin qubit arrays. Dispersive gate-sensing is realised in combination with charge detection based on two radio frequency quantum point contacts to perform multiplexed readout of a double quantum dot in the few-electron regime. Demonstration of a 10-channel multiplexing device is achieved and limitations in scaling spin qubit readout to large numbers using multiplexed channels discussed. The final experiment ties previously presented results together by realising a micro-architecture for controlling and reading out qubits during the execution of a quantum algorithm. The basic principles of this architecture are demonstrated via the manipulation of a semiconductor qubit using control pulses that are cryogenically routed using a high-electron mobility transistor switching matrix controlled by a field programmable gate array. Finally, several technical results are also presented including the development of printed circuit board solutions to allow the high-frequency measurement of nanoscale devices at cryogenic temperatures and the design of on-chip interconnects used to suppress electromagnetic crosstalk in high-density spin qubit device architectures.
We report on charge sensing measurements of a GaAs semiconductor quantum dot device using a radio frequency quantum point contact (rf-QPC). The rf-QPC is fully characterized at 4K and millikelvin temperatures and found to have a bandwidth exceeding 20MHz. For single shot charge sensing, we achieve a charge sensitivity of ∼2×10−4e∕Hz referred to the neighboring dot’s charge. The rf-QPC compares favorably with rf single electron transistor electrometers and promises to be an extremely useful tool for characterizing and measuring semiconductor quantum systems on fast time scales.
As with any quantum computing platform, semiconductor quantum dot devices require sophisticated hardware and controls for operation. The increasing complexity of quantum dot devices necessitates the advancement of automated control software and image recognition techniques for rapidly evaluating charge stability diagrams. We use an image analysis toolbox developed in Python to automate the calibration of virtual gates, a process that previously involved a large amount of user intervention. Moreover, we show that straightforward feedback protocols can be used to simultaneously tune multiple tunnel couplings in a triple quantum dot in a computer automated fashion. Finally, we adopt the use of a “tunnel coupling lever arm” to model the interdot barrier gate response and discuss how it can be used to more rapidly tune interdot tunnel couplings to the gigahertz values that are compatible with exchange gates.
Semiconductor quantum dot arrays are a promising platform to perform spin-based error-corrected quantum computation with large numbers of qubits. However, due to the diverging number of possible charge configurations combined with the limited sensitivity of large-footprint charge sensors, achieving single-spin occupancy in each dot in a growing quantum dot array is exceedingly complex. Therefore, to scale-up a spin-based architecture we must change how individual charges are readout and controlled. Here, we demonstrate single-spin occupancy of each dot in a foundry-fabricated array by combining two methods. 1/ Loading a finite number of electrons into the quantum dot array; simplifying electrostatic tuning by isolating the array from the reservoirs. 2/ Deploying multiplex gate-based reflectometry to dispersively probe charge tunneling and spin states without charge sensors or reservoirs. Our isolated arrays probed by embedded multiplex readout can be readily electrostatically tuned. They are thus a viable, scalable approach for spin-based quantum architectures. Large-footprint, low-sensitivity charge sensors hinder scaling semiconductor quantum dot arrays for quantum computation. Here the authors present a potentially scalable approach using multiplexed gate-based readout and operation in a foundry-fabricated quantum dot array, demonstrating single-electron occupancy.