Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1811.06496 · Applied Physics Letters

High kinetic inductance microwave resonators made by He-Beam assisted deposition of tungsten nanowires

J. Basset, D. Watfa, Gianluca Aiello, Mathieu Féchant, Alexis Morvan, Jérôme Estève, Julien Gabelli, M. Aprili, Raphaël Weil, Alik Yu. Kasumov, Hélène Bouchiat, R. Deblock

Published Mar 11, 2019• 34 citations
arXivHTMLPDF

Abstract

We evaluate the performance of hybrid microwave resonators made by combining sputtered Nb thin films with Tungsten nanowires grown with a He-beam induced deposition technique. Depending on growth conditions, the nanowires have a typical width w∈[35−75] nm and thickness t∈[5−40] nm. We observe a high normal state resistance R◻∈[65−150] Ω/◻ which together with a critical temperature Tc∈[4−6] K ensures a high kinetic inductance making the resonator strongly nonlinear. Both lumped and coplanar waveguide resonators were fabricated and measured at low temperature exhibiting internal quality factors up to 3990 at 4.5 GHz in the few photon regime. Analyzing the wire length, temperature, and microwave power dependence, we extracted a kinetic inductance for the W nanowire of LK≈15 pH/◻, which is 250 times higher than the geometrical inductance, and a Kerr non-linearity as high as KW,He/2π=200±120 Hz/photon at 4.5 GHz. The nanowires made with the helium focused ion beam are thus versatile objects to engineer compact, high impedance, superconducting environments with a mask and resist free direct write process.

DOI
10.1063/1.5080925

Related papers

Magnetic field resilient high kinetic inductance superconducting niobium nitride coplanar waveguide resonators

Cécile Xinqing Yu, Simon Zihlmann, Gonzalo Troncoso Fernández-Bada +4 more

We characterize niobium nitride (NbN) λ/2 coplanar waveguide resonators, which were fabricated from a 10-nm-thick film on silicon dioxide grown by sputter deposition. For films grown at 180 °C, we report a superconducting critical temperature of 7.4 K associated with a normal square resistance of 1 kΩ, leading to a kinetic inductance of 192 pH/◻. We fabricated resonators with a characteristic impedance up to 4.1 kΩ and internal quality factors Qi>104 in the single photon regime at zero magnetic field. Moreover, in the many photon regime, the resonators present a high magnetic field resilience with Qi>104 in a 6 T in-plane magnetic field and in a 300 mT out-of-plane magnetic field. These findings make such resonators a compelling choice for circuit quantum electrodynamics experiments involving quantum systems with small electric dipole moments operated in finite magnetic fields.

arXiv:2012.04366•Applied Physics Letters•Feb 1, 2021•66 citations

Engineering high-Q superconducting tantalum microwave coplanar waveguide resonators for compact coherent quantum circuit

Shima Poorgholam-Khanjari, Valentino Seferai, Paniz Foshat +5 more

Abstract Tantalum (Ta) has recently received considerable attention in manufacturing robust superconducting quantum circuits. Ta offers low microwave loss, high kinetic inductance compared to aluminium (Al) and niobium (Nb), and good compatibility with complementary metal-oxide-semiconductor (CMOS) technology, which is essential for quantum computing applications. Here we demonstrate the fabrication engineering of thickness-dependent high-quality-factor (high- $$\:{Q}_{i}$$ ) Ta superconducting microwave coplanar waveguide resonators. All films are deposited on high-resistivity silicon substrates at room temperature without additional substrate heating. Before Ta deposition, a niobium (Nb) seed layer is used to promote a body-centred cubic lattice ( $$\:\alpha\:$$ -Ta) formation. We further engineer the kinetic inductance ( $$\:{L}_{K}$$ ) of the resonators by varying Ta film thicknesses. High $$\:{L}_{K}$$ is a key advantage for applications because it facilitates the realisation of high-impedance, compact quantum circuits with enhanced coupling to qubits. The maximum internal quality factor $$\:{Q}_{i}$$ of $$\:\sim\:$$ 3.6 × 10 6 in the high power regime and $$\:{Q}_{i}$$ of $$\:\sim\:$$ 4.5 × 10 5 in the single-photon regime is achieved for 100 nm Ta which represents an improvement over previous room-temperature deposited Ta resonators on silicon substrates in the single photon regime, while the highest kinetic inductance of 0.6 pH/sq is obtained for the thinnest film, which is 40 nm. This combination of high $$\:{Q}_{i}$$ and high $$\:{L}_{K}$$ highlights the potential of Ta microwave circuits for high-fidelity operation of compact quantum circuits.

arXiv:2412.16099•Scientific Reports•Jul 25, 2025•20 citations

Temperature dependence of microwave losses in lumped-element resonators made from superconducting nanowires with high kinetic inductance

Ermes Scarano, Elisabet K. Arvidsson, August K. Roos +2 more

Abstract We study the response of several microwave resonators made from superconducting NbTiN thin-film meandering nanowires with large kinetic inductance, having different circuit topology and coupling to the transmission line. Reflection measurements reveal the parameters of the circuit and analysis of their temperature dependence in the range 1.7–6 K extract the superconducting energy gap and critical temperature. The lumped-element LC resonator, valid in our frequency range of interest, allows us to predict the quasiparticle (QP) contribution to internal loss, independent of circuit topology and characteristic impedance. Our analysis shows that the internal quality factor is limited not by thermal-equilibrium QP, but an additional temperature-dependent source of internal microwave loss.

arXiv:2401.02943•Superconductor Science and Technology•May 19, 2024•4 citations

Ultra high quality factor resonators for kinetic inductance detectors

G. Hammer, S. Wünsch, K. Ilin +1 more

The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.

Journal of Physics Conference Series•Feb 1, 2008•12 citations

Kinetic inductance compact resonator with NbTiN micronwires

Ming Yang, Xiaoliang He, Wanpeng Gao +6 more

Nonlinear resonators of superconducting thin-film kinetic inductance have attracted considerable research interest in the fields of detectors, qubits, parametric amplifiers, and more. By tuning the deposition parameters, niobium titanium nitride (NbTiN) films (∼12 nm in thickness) present high resistivity(∼2000 μΩ cm) and large sheet kinetic inductance (∼0.7 nH/□). We designed resonators with NbTiN micronwire as the inductor and aluminum as the capacitor, which result in a high internal quality factor and a Kerr nonlinearity of a few hertz. The radio frequency response of the resonators demonstrates nonlinear behavior similar to that of the cubic Duffing oscillator, including frequency shift and hysteresis region. The kinetic inductance resonator is a promising candidate for high saturation power parametric amplifiers.

AIP Advances•Aug 1, 2024•8 citations

Investigation of kinetic inductance and microwave loss in thin-film TaCxN1−x superconducting resonators

Iliya Shiravand, Moeid Jamalzadeh, Man Nguyen +7 more

The promise of tantalum for realizing superconducting quantum devices has generated interest in its compound films, particularly nitrides. Among these, cubic-phase tantalum carbonitride (TaCxN1−x) offers reduced susceptibility to oxidation and a high critical temperature, yet its microwave properties remain largely unexplored. Here, we investigate plasma-enhanced atomic layer deposition of cubic-phase TaCxN1−x thin films for superconducting microwave circuits. Structural and transport measurements reveal nanocrystalline morphology with sub-10 nm grains and superconductivity in the dirty limit. Coplanar waveguide resonators exhibit moderately high kinetic inductance (16.8 pH/sq for 30 nm films) with potential for enhancement through dimensional scaling. The films also support high internal quality factors exceeding 105 at 50 mK in the single-photon regime, comparable to granular aluminum. Loss analysis identifies the two-level systems as the dominant limiting mechanism, with potential for further reduction through interface engineering. These results establish atomic layer deposited TaCxN1−x as a promising material for scalable, low-loss, high-inductance superconducting circuits.

Applied Physics Letters•Nov 10, 2025•1 citation
We evaluate the performance of hybrid microwave resonators made by combining sputtered Nb thin films with Tungsten nanowires grown with a He-beam induced deposition technique. Depending on growth conditions, the nanowires have a typical width w∈[35−75] nm and thickness t∈[5−40] nm. We observe a high normal state resistance R◻∈[65−150] Ω/◻ which together with a critical temperature Tc∈[4−6] K ensures a high kinetic inductance making the resonator strongly nonlinear. Both lumped and coplanar waveguide resonators were fabricated and measured at low temperature exhibiting internal quality factors up to 3990 at 4.5 GHz in the few photon regime. Analyzing the wire length, temperature, and microwave power dependence, we extracted a kinetic inductance for the W nanowire of LK≈15 pH/◻, which is 250 times higher than the geometrical inductance, and a Kerr non-linearity as high as KW,He/2π=200±120 Hz/photon at 4.5 GHz. The nanowires made with the helium focused ion beam are thus versatile objects to engineer compact, high impedance, superconducting environments with a mask and resist free direct write process.
We characterize niobium nitride (NbN) λ/2 coplanar waveguide resonators, which were fabricated from a 10-nm-thick film on silicon dioxide grown by sputter deposition. For films grown at 180 °C, we report a superconducting critical temperature of 7.4 K associated with a normal square resistance of 1 kΩ, leading to a kinetic inductance of 192 pH/◻. We fabricated resonators with a characteristic impedance up to 4.1 kΩ and internal quality factors Qi>104 in the single photon regime at zero magnetic field. Moreover, in the many photon regime, the resonators present a high magnetic field resilience with Qi>104 in a 6 T in-plane magnetic field and in a 300 mT out-of-plane magnetic field. These findings make such resonators a compelling choice for circuit quantum electrodynamics experiments involving quantum systems with small electric dipole moments operated in finite magnetic fields.
Abstract Tantalum (Ta) has recently received considerable attention in manufacturing robust superconducting quantum circuits. Ta offers low microwave loss, high kinetic inductance compared to aluminium (Al) and niobium (Nb), and good compatibility with complementary metal-oxide-semiconductor (CMOS) technology, which is essential for quantum computing applications. Here we demonstrate the fabrication engineering of thickness-dependent high-quality-factor (high-  Qi\:{Q}_{i}Qi​ ) Ta superconducting microwave coplanar waveguide resonators. All films are deposited on high-resistivity silicon substrates at room temperature without additional substrate heating. Before Ta deposition, a niobium (Nb) seed layer is used to promote a body-centred cubic lattice (  α \:\alpha\:α -Ta) formation. We further engineer the kinetic inductance (  LK\:{L}_{K}LK​ ) of the resonators by varying Ta film thicknesses. High  LK\:{L}_{K}LK​ is a key advantage for applications because it facilitates the realisation of high-impedance, compact quantum circuits with enhanced coupling to qubits. The maximum internal quality factor  Qi\:{Q}_{i}Qi​ of  ∼ \:\sim\:∼ 3.6 × 10 6 in the high power regime and  Qi\:{Q}_{i}Qi​ of  ∼ \:\sim\:∼ 4.5 × 10 5 in the single-photon regime is achieved for 100 nm Ta which represents an improvement over previous room-temperature deposited Ta resonators on silicon substrates in the single photon regime, while the highest kinetic inductance of 0.6 pH/sq is obtained for the thinnest film, which is 40 nm. This combination of high  Qi\:{Q}_{i}Qi​ and high  LK\:{L}_{K}LK​ highlights the potential of Ta microwave circuits for high-fidelity operation of compact quantum circuits.
Abstract We study the response of several microwave resonators made from superconducting NbTiN thin-film meandering nanowires with large kinetic inductance, having different circuit topology and coupling to the transmission line. Reflection measurements reveal the parameters of the circuit and analysis of their temperature dependence in the range 1.7–6 K extract the superconducting energy gap and critical temperature. The lumped-element LC resonator, valid in our frequency range of interest, allows us to predict the quasiparticle (QP) contribution to internal loss, independent of circuit topology and characteristic impedance. Our analysis shows that the internal quality factor is limited not by thermal-equilibrium QP, but an additional temperature-dependent source of internal microwave loss.
The sensitivity of a kinetic inductance detector is determined by the performance of the cavity circuit and therefore a high quality factor and low phase noise are required. We developed superconducting niobium coplanar waveguide resonators for kinetic inductance detectors at a resonance frequency of 6 GHz. The length of the resonators is adjusted to a quarter of a wavelength which corresponds to ≈ 5.3 mm in our geometry. Different layouts with coplanar waveguide transmission line topology for the resonator were designed and simulated. Some parameters of the device fabrication process were varied. The niobium thin films were deposited by magnetron sputtering on sapphire substrates kept at ambient temperature. The resonators were patterned by photolithography and reactive ion etching and measured at helium temperatures. Because of the quarter wave geometry with one shorted end the reflection parameter was measured. We have studied the influence of the coupling capacitances on quality factor. The optimization includes microwave simulations and implementation in different resonator structures. The measurements of optimized devices showed a very high quality factor above one million (10 6 ). The obtained results and perspective on further development of resonators will be discussed.
Nonlinear resonators of superconducting thin-film kinetic inductance have attracted considerable research interest in the fields of detectors, qubits, parametric amplifiers, and more. By tuning the deposition parameters, niobium titanium nitride (NbTiN) films (∼12 nm in thickness) present high resistivity(∼2000 μΩ cm) and large sheet kinetic inductance (∼0.7 nH/□). We designed resonators with NbTiN micronwire as the inductor and aluminum as the capacitor, which result in a high internal quality factor and a Kerr nonlinearity of a few hertz. The radio frequency response of the resonators demonstrates nonlinear behavior similar to that of the cubic Duffing oscillator, including frequency shift and hysteresis region. The kinetic inductance resonator is a promising candidate for high saturation power parametric amplifiers.
The promise of tantalum for realizing superconducting quantum devices has generated interest in its compound films, particularly nitrides. Among these, cubic-phase tantalum carbonitride (TaCxN1−x) offers reduced susceptibility to oxidation and a high critical temperature, yet its microwave properties remain largely unexplored. Here, we investigate plasma-enhanced atomic layer deposition of cubic-phase TaCxN1−x thin films for superconducting microwave circuits. Structural and transport measurements reveal nanocrystalline morphology with sub-10 nm grains and superconductivity in the dirty limit. Coplanar waveguide resonators exhibit moderately high kinetic inductance (16.8 pH/sq for 30 nm films) with potential for enhancement through dimensional scaling. The films also support high internal quality factors exceeding 105 at 50 mK in the single-photon regime, comparable to granular aluminum. Loss analysis identifies the two-level systems as the dominant limiting mechanism, with potential for further reduction through interface engineering. These results establish atomic layer deposited TaCxN1−x as a promising material for scalable, low-loss, high-inductance superconducting circuits.