We present and demonstrate a general three-step method for extracting the quantum efficiency of dispersive qubit readout in circuit QED. We use active depletion of post-measurement photons and optimal integration weight functions on two quadratures to maximize the signal-to-noise ratio of the non-steady-state homodyne measurement. We derive analytically and demonstrate experimentally that the method robustly extracts the quantum efficiency for arbitrary readout conditions in the linear regime. We use the proven method to optimally bias a Josephson traveling-wave parametric amplifier and to quantify different noise contributions in the readout amplification chain.
We present and demonstrate a general three-step method for extracting the quantum efficiency of dispersive qubit readout in circuit QED. We use active depletion of post-measurement photons and optimal integration weight functions on two quadratures to maximize the signal-to-noise ratio of the non-steady-state homodyne measurement. We derive analytically and demonstrate experimentally that the method robustly extracts the quantum efficiency for arbitrary readout conditions in the linear regime. We use the proven method to optimally bias a Josephson traveling-wave parametric amplifier and to quantify different noise contributions in the readout amplification chain.
We investigate the quantum measurement physics of a system in which a phase-sensitive parametric amplifier is used to directly measure a qubit to which it is coupled dispersively. By analytic calculation of the signal-to-noise ratio, we show that the amplification properties of the paramp can be exploited to achieve on-chip gain of the qubit readout signal, mitigating the damage done to the measurement rate by circulator added noise and losses in between the readout cavity and any following amplification chain. With a different choice of drive phase, we show that when added noise is not a concern, the squeezing properties of the paramp can be used to enhance the measurement rate relative to a standard dispersive readout by reducing the readout noise without corresponding reduction of qubit signal. We then proceed to calculate the back-action dephasing of the qubit by way of a phase-space technique, and find analytic results valid in the long-time limit while numerically handling the finite-time case. We show how in both operating modes, in the long-time limit, the back-action dephasing of the qubit can be made as small as is allowed by quantum mechanics by using using sufficiently many photons in the measurement, i.e.\@ by using a sufficiently strong coherent measurement drive. Crucially, we find that in the presence of experimentally realistic amounts of added noise, the on-chip gain afforded by such a device can be used to come significantly closer to the quantum limit than is possible with a standard dispersive measurement setup, allowing for efficiencies of ~ 75% under conditions that would yield efficiencies <~ 1 % when applying the usual scheme.
The ability to perform high-fidelity quantum nondemolition qubit readout is pivotal for the realization of large and powerful quantum computers. Such readout of superconducting qubits is generally enabled by amplifying the weak dispersive measurement signals using phase-preserving quantum-limited Josephson amplifiers with sufficient gain to dilute the contribution of the added noise by the output chain. Here, we further enhance the qubit readout fidelity by (1) simultaneously measuring the two-mode squeezed states of the amplified readout signals at the signal and idler frequencies of the nondegenerate amplifier and (2) coherently combining them at the classical processing stage following a relative rotation that maximizes the signal to noise ratio of the qubit-encoded readout quadrature. Such readout scheme exhibits enhancement in the readout fidelity for all practical values of amplifier gain and noise added by the output chain and is fully compatible with frequency multiplexed setups used in large quantum processors.
Fault-tolerant quantum information processing with flawed qubits and gates requires highly efficient, quantum nondemolition qubit readout. In superconducting circuits, qubit readout using coherent light with fidelity above 99% has been achieved by using quantum limited parametric amplifiers such as the Josephson parametric converter (JPC). However, further improvement of such measurement faces many challenges, including the vacuum fluctuation of the coherent light that limits measurement fidelity. In this work we demonstrate dispersive qubit readout with a two-mode squeezed light interferometer formed by two JPCs. The first JPC generates two-mode squeezed vacuum at its output, which is coherently recombined by the second JPC after one branch is phase shifted and displaced by its interaction with the qubit-cavity system on that arm of the interferometer. We observe a 31% improvement in the power signal-to-noise ratio (SNR) of projective readout after replacing vacuum fluctuation in the readout cavity with two-mode squeezed vacuum containing on average one photon. This demonstrates a more efficient way of improving SNR than by increasing readout power. Furthermore, we investigate the quantum properties of the two-mode squeezed light in the system through weak measurement. Surprisingly, we find that tuning the interferometer to be less projective increases the measurement efficiency relative to the optimum setting for projective measurement. These enhancements may enable remote entanglement with lower efficiency components in a system with qubits in both arms of the interferometer.
In a circuit QED architecture, we experimentally demonstrate a hardware-efficient and qubit-state-dependent Single-Step Phase-Engineered (SSPE) pulse scheme for actively depopulating a readout cavity. The protocol appends a reset segment with tailored amplitude and phase to a square readout pulse. Within the linear-response regime, the optimal reset amplitude scales proportionally with the readout amplitude, while the optimal reset phase remains invariant, significantly simplifying the experimental calibration procedure. For a known qubit state, time-resolved measurements demonstrate that the SSPE pulse achieves faster cavity depletion than the CLEAR protocol. Crucially, this approach enables arbitrarily fast, overshoot-free depletion of the cavity photon population, with the ultimate reset rate constrained by the available drive amplitude and the finite analog bandwidth of the measurement chain. A comprehensive evaluation of the QND character reveals no measurable increase in non-QNDness relative to the free-decay and CLEAR protocols. The remaining non-QNDness is predominantly attributable to state switching induced by qubit relaxation during the readout process. These results establish the SSPE scheme as a practical and scalable approach for achieving rapid and smooth cavity reset in superconducting quantum circuits in the case of a known qubit state.
Superconducting electrical circuits can be used to study the physics of cavity quantum electrodynamics (QED) in new regimes, therefore realizing circuit QED. For quantum-information processing and quantum optics, an interesting regime of circuit QED is the dispersive regime, where the detuning between the qubit transition frequency and the resonator frequency is much larger than the interaction strength. In this paper, we investigate how nonlinear corrections to the dispersive regime affect the measurement process. We find that in the presence of pure qubit dephasing, photon population of the resonator used for the measurement of the qubit act as an effective heat bath, inducing incoherent relaxation and excitation of the qubit. Measurement thus induces both dephasing and mixing of the qubit, something that can reduce the quantum nondemolition aspect of the readout. Using quantum trajectory theory, we show that this heat bath can induce quantum jumps in the qubit state. Nonlinear effects can also reduce the achievable signal-to-noise ratio of a homodyne measurement of the voltage.
We perform a detailed analysis of how an amplified interferometer can be used to enhance the quality of a dispersive qubit measurement, such as one performed on a superconducting transmon qubit, using homodyne detection on an amplified microwave signal. Our modeling makes a realistic assessment of what is possible in current circuit-QED experiments; in particular, we take into account the frequency dependence of the qubit-induced phase shift for short microwaves pulses. We compare the possible signal-to-noise ratios obtainable with (single-mode) SU(1,1) interferometers with the current coherent measurement and find a considerable reduction in measurement error probability in an experimentally accessible range of parameters.