Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1707.09061 · Physical Review Applied

Measuring a Quantum Dot with an Impedance-Matching On-Chip Superconducting LC Resonator at Gigahertz Frequencies

M.-C. Harabula, T. Hasler, G. Fülöp, M. Jung, V. Ranjan, Christian Schönenberger

Published Nov 6, 2017• 17 citations
arXivHTMLPDF

Abstract

It can be hard to find that perfect match---even, or perhaps especially, in quantum electronics. Microwave readout of highly Ohmic quantum devices, like superconducting qubits, necessitates impedance-matching circuits to maximize power transfer. $L\phantom{\rule{0}{0ex}}C$ resonant circuits enjoy two major advantages over well-established coplanar transmission-line circuits: larger bandwidths (and thus shorter readout times), and drastically smaller on-chip footprints. With this in mind, the authors develop a compact $L\phantom{\rule{0}{0ex}}C$ resonator operating at 3 GHz to bridge a load of ~15 k$\mathrm{\ensuremath{\Omega}}$ to a typical coaxial line at 50 $\mathrm{\ensuremath{\Omega}}$---match made.

DOI
10.1103/physrevapplied.8.054006

Related papers

Shot Noise of a Quantum Dot Measured with Gigahertz Impedance Matching

T. Hasler, M. Jung, V. Ranjan +3 more

Modern experiments using high-speed, high-impedance devices such as quantum dots can suffer from strong suppression of signal power, if components are not carefully impedance-matched. To overcome this problem, the authors show that a resonant impedance-matching circuit based on superconducting transmission lines can improve the signal to noise ratio by nearly three orders of magnitude. This technology is particularly important to noise studies of electron transport in quantum systems, which can provide information that is unattainable by other means.

arXiv:1507.04884•Physical Review Applied•Nov 3, 2015•18 citations

Admittance and noise detection in mesoscopic systems via GHz impedance matching

V. Ranjan

Fast measurement of small currents and even smaller fluctuations in devices with large impedance is not trivial. Standard low frequency lock-in measurements suffer from stray capacitance of the order of nF reducing the bandwidth to merely kHz and a time resolution of ms. One approach of increasing the bandwidth is to connect the high-impedance device next to a low input impedance amplifier, though, the signal is decreased by the ratio of the impedances of the device and the amplifier, easily a factor of a thousand. Therefore, long averaging times are required to detect the small signal. Moreover, 1/f noise still affects the measurements. The issues of small bandwidth, impedance mismatch and 1/f noise can be simultaneously addressed using resonant LC circuits. The success of this impedance transformer lies in replacing the slow operation of applying voltages and measuring currents by applying fast radio frequency signals and measuring the reflectance. LC circuits remain appealing because of a rather simple assembly. Nonetheless, the challenge to reproducibly achieve the resonance frequencies in gigahertz (GHz) range while matching to high impedance still remains due to the large parallel stray capacitance of the measurement setup. Resonance frequency in GHz range is desirable for two reasons. Firstly, measurements are faster and 1/f noise smaller. Yet more importantly, one can profit from the wide range of measurement techniques developed in the context of circuit quantum electrodynamics, such as FPGA based hardware and quantum limited Josephson parametric amplifiers. \n \nIn this thesis, a matching circuit namely stub tuner based on coplanar transmission lines is designed, fabricated and integrated with mesoscopic devices. Owing to the simple design, we could predict the frequency response of a stub tuner in terms of the standard circuit model (Chapter 3). We initiated certain necessary fabrication adaptations to achieve integration of niobium circuits with devices. In particular, a reliable stamping of carbon nanotubes from the growth substrate to the target substrate was accomplished, improving both the device quality and yield (Chapter 4). RF reflectometry is employed to perform admittance measurements on CNT quantum dots. We could reliably deduce all circuit and device properties using the resonance response. The measurement bandwidth is shown to be in MHz range which is three orders of magnitude larger than that for DC measurements. In particular, using the phase response of the circuit, double-dot qubit energy and dephasing rate are studied (Chapter 5). We could even get rid of conventional contacts that could degrade the device properties, and still extract quantum capacitance and dissipation in graphene p-n junctions. The residual doping is shown to affect not only the mean free path but also the Fermi velocity. We further see that at small doping, electron-electron interactions could modify the Fermi velocity and that the dispersion relation could deviate from linearity (Chapter 6). \n \nIn the second half of the scientific results, real strength of stub tuner is tested in transmission measurements. The large bandwidth and signal to noise ratio is utilized to measure extremely clean noise power densities at high speed and draw comparisons with the corresponding average current. Clear changes in the shot noise spectrum are seen when a transport channel is added or removed from the bias window of the quantum dot. We especially observe noise enhancement outside the Coulomb diamonds due to blocking states (Chapter 7). Finally, we investigate noise properties of quantum dots when leads are superconducting. Distinct charge transfers due to multiple Andreev reflections are visible in the shot noise. The main finding, however, was the thermal noise at zero bias. We observed its periodic suppression and emergence across the quantum dot resonance. In another device, shot noise due to the Kondo effect is found to be enhanced in the superconducting state when the Kondo temperature exceeds the value of the superconducting gap (Chapter 8). Simple design and reliable calibration of the GHz matching circuit in both reflectance and transmission pave a way for fast and non-invasive measurements of mesoscopic conductors. \n \n \n \n \n

•Jan 1, 2017•0 citations

Clean carbon nanotubes coupled to superconducting impedance-matching circuits

V. Ranjan, Gabriel Puebla‐Hellmann, Minkyung Jung +6 more

Coupling carbon nanotube devices to microwave circuits offers a significant increase in bandwidth (BW) and signal-to-noise ratio. These facilitate fast non-invasive readouts important for quantum information processing, shot noise and correlation measurements. However, creation of a device that unites a low-disorder nanotube with a low-loss microwave resonator has so far remained a challenge, due to fabrication incompatibility of one with the other. Employing a mechanical transfer method, we successfully couple a nanotube to a gigahertz superconducting matching circuit and thereby retain pristine transport characteristics such as the control over formation of, and coupling strengths between, the quantum dots. Resonance response to changes in conductance and susceptance further enables quantitative parameter extraction. The achieved near matching is a step forward promising high-BW noise correlation measurements on high impedance devices such as quantum dot circuits. Radio-frequency circuits offer fast low-noise detection of signals in carbon nanotubes, but incompatibilities in fabrication degrade the performance of the hybrid device. Here, the authors use a deterministic mechanical transfer to couple pristine nanotubes to a gigahertz superconducting matching circuit.

arXiv:1505.04681•Nature Communications•May 15, 2015•52 citations

Development of high quality superconducting resonators for quantum device applications

Dong-Gwang Ha, Seon Hoo Kim, So-Yeon Jun +5 more

We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•0 citations

A Versatile Analytical Model for Fast and Accurate Determination of Feedline-Coupled Resonators for Superconducting Qubit Readout

Zhen Luo, Lea Richard, Ivan Tsitsilin +4 more

Superconducting quantum chips commonly utilize quarter-wavelength (λ/4) transmission line resonators as readout circuits. An analytical model for the accurate determination of resonance frequencies and coupling Q-factors of feedline-coupled superconducting resonators is introduced. The model leverages four-port microwave network analysis, integrating boundary conditions and conformal mapping techniques to compute even- and odd-mode impedances in edge-coupled coplanar waveguide (CPW) structures. Its versatility allows application to both planar and 3-D heterogeneous architectures, making it a powerful tool for resonator design. To validate the model, a test chip with λ/4 resonators of varying geometries is fabricated and measured in a cryogenic environment. Comparisons with finite element method (FEM) simulations and experimental measurements confirm the model's accuracy, with resonance frequencies and coupling Q-factors aligning closely across configurations. This proposed model facilitates the design of superconducting resonators in readout circuits for more effective, scalable, and adaptable quantum computing architectures.

quant-pharXiv:2607.00490•IEEE Transactions on Microwave Theory and Techniques•Jul 2, 2026•2 citations

Design and Modeling of Double-Fold Superconducting High-Q Coplanar Waveguide Resonators for Quantum Applications

Jagmohan Singh, Hongxiang Shen, Nobuyuki Yoshikawa +2 more

In this paper, we present a novel design of a compact, double-fold half-wave superconducting coplanar waveguide resonator, specifically optimized for quantum readout. The geometry offers advantages in terms of scalability and allows for a more compact integration of qubits per unit area. The superconducting resonators are designed to operate within a fundamental frequency range of 1.9 GHz$-$1.95 GHz, utilizing both gap and finger coupling schemes. The devices are fabricated using thin aluminum films deposited on high-resistivity sapphire substrates. The proposed resonators exhibit quality factor (Q$_{L}$) of 2.9 ×$ 10^{5}$and 1.58 ×$10^{3}$for gap coupled and finger coupled, respectively, during experimental measurements. The simulated Q$_{L}$of single-folded meander line resonators are found to be 4.65 ×$10^{5}$and 258.42, for gap coupled and finger coupled, respectively, for comparison purpose at similar operating frequency. A comprehensive analysis of the microwave transmission spectra was conducted at cryogenic temperatures near 10 mK, across very high input drive powers ($-$30 dBm to$-$10 dBm). Experimental results show a good agreement with simulations and the equivalent lumped circuit model. Notably, the proposed design reduces the physical footprint of the resonator devices up to 28.2$\%$compared to conventional single-fold meandered structures. The resonators demonstrate strong potential for integrating qubits with readout and control buses in quantum information processing which require a Q$_{L}$between$10^{4}$$-$$10^{5}$. They also being well-suited for cryogenic detector applications that utilize microwave kinetic inductance detector (MKID) arrays in frequency multiplexing for different coupling schemes.

IEEE Transactions on Applied Superconductivity•Sep 1, 2025•3 citations
It can be hard to find that perfect match---even, or perhaps especially, in quantum electronics. Microwave readout of highly Ohmic quantum devices, like superconducting qubits, necessitates impedance-matching circuits to maximize power transfer. L\phantom{\rule{0}{0ex}}C resonant circuits enjoy two major advantages over well-established coplanar transmission-line circuits: larger bandwidths (and thus shorter readout times), and drastically smaller on-chip footprints. With this in mind, the authors develop a compact L\phantom{\rule{0}{0ex}}C resonator operating at 3 GHz to bridge a load of ~15 k\ensuremathΩ\mathrm{\ensuremath{\Omega}}\ensuremathΩ to a typical coaxial line at 50 \ensuremathΩ\mathrm{\ensuremath{\Omega}}\ensuremathΩ---match made.
Modern experiments using high-speed, high-impedance devices such as quantum dots can suffer from strong suppression of signal power, if components are not carefully impedance-matched. To overcome this problem, the authors show that a resonant impedance-matching circuit based on superconducting transmission lines can improve the signal to noise ratio by nearly three orders of magnitude. This technology is particularly important to noise studies of electron transport in quantum systems, which can provide information that is unattainable by other means.
Fast measurement of small currents and even smaller fluctuations in devices with large impedance is not trivial. Standard low frequency lock-in measurements suffer from stray capacitance of the order of nF reducing the bandwidth to merely kHz and a time resolution of ms. One approach of increasing the bandwidth is to connect the high-impedance device next to a low input impedance amplifier, though, the signal is decreased by the ratio of the impedances of the device and the amplifier, easily a factor of a thousand. Therefore, long averaging times are required to detect the small signal. Moreover, 1/f noise still affects the measurements. The issues of small bandwidth, impedance mismatch and 1/f noise can be simultaneously addressed using resonant LC circuits. The success of this impedance transformer lies in replacing the slow operation of applying voltages and measuring currents by applying fast radio frequency signals and measuring the reflectance. LC circuits remain appealing because of a rather simple assembly. Nonetheless, the challenge to reproducibly achieve the resonance frequencies in gigahertz (GHz) range while matching to high impedance still remains due to the large parallel stray capacitance of the measurement setup. Resonance frequency in GHz range is desirable for two reasons. Firstly, measurements are faster and 1/f noise smaller. Yet more importantly, one can profit from the wide range of measurement techniques developed in the context of circuit quantum electrodynamics, such as FPGA based hardware and quantum limited Josephson parametric amplifiers. \n \nIn this thesis, a matching circuit namely stub tuner based on coplanar transmission lines is designed, fabricated and integrated with mesoscopic devices. Owing to the simple design, we could predict the frequency response of a stub tuner in terms of the standard circuit model (Chapter 3). We initiated certain necessary fabrication adaptations to achieve integration of niobium circuits with devices. In particular, a reliable stamping of carbon nanotubes from the growth substrate to the target substrate was accomplished, improving both the device quality and yield (Chapter 4). RF reflectometry is employed to perform admittance measurements on CNT quantum dots. We could reliably deduce all circuit and device properties using the resonance response. The measurement bandwidth is shown to be in MHz range which is three orders of magnitude larger than that for DC measurements. In particular, using the phase response of the circuit, double-dot qubit energy and dephasing rate are studied (Chapter 5). We could even get rid of conventional contacts that could degrade the device properties, and still extract quantum capacitance and dissipation in graphene p-n junctions. The residual doping is shown to affect not only the mean free path but also the Fermi velocity. We further see that at small doping, electron-electron interactions could modify the Fermi velocity and that the dispersion relation could deviate from linearity (Chapter 6). \n \nIn the second half of the scientific results, real strength of stub tuner is tested in transmission measurements. The large bandwidth and signal to noise ratio is utilized to measure extremely clean noise power densities at high speed and draw comparisons with the corresponding average current. Clear changes in the shot noise spectrum are seen when a transport channel is added or removed from the bias window of the quantum dot. We especially observe noise enhancement outside the Coulomb diamonds due to blocking states (Chapter 7). Finally, we investigate noise properties of quantum dots when leads are superconducting. Distinct charge transfers due to multiple Andreev reflections are visible in the shot noise. The main finding, however, was the thermal noise at zero bias. We observed its periodic suppression and emergence across the quantum dot resonance. In another device, shot noise due to the Kondo effect is found to be enhanced in the superconducting state when the Kondo temperature exceeds the value of the superconducting gap (Chapter 8). Simple design and reliable calibration of the GHz matching circuit in both reflectance and transmission pave a way for fast and non-invasive measurements of mesoscopic conductors. \n \n \n \n \n
Coupling carbon nanotube devices to microwave circuits offers a significant increase in bandwidth (BW) and signal-to-noise ratio. These facilitate fast non-invasive readouts important for quantum information processing, shot noise and correlation measurements. However, creation of a device that unites a low-disorder nanotube with a low-loss microwave resonator has so far remained a challenge, due to fabrication incompatibility of one with the other. Employing a mechanical transfer method, we successfully couple a nanotube to a gigahertz superconducting matching circuit and thereby retain pristine transport characteristics such as the control over formation of, and coupling strengths between, the quantum dots. Resonance response to changes in conductance and susceptance further enables quantitative parameter extraction. The achieved near matching is a step forward promising high-BW noise correlation measurements on high impedance devices such as quantum dot circuits. Radio-frequency circuits offer fast low-noise detection of signals in carbon nanotubes, but incompatibilities in fabrication degrade the performance of the hybrid device. Here, the authors use a deterministic mechanical transfer to couple pristine nanotubes to a gigahertz superconducting matching circuit.
We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.
Superconducting quantum chips commonly utilize quarter-wavelength (λ/4) transmission line resonators as readout circuits. An analytical model for the accurate determination of resonance frequencies and coupling Q-factors of feedline-coupled superconducting resonators is introduced. The model leverages four-port microwave network analysis, integrating boundary conditions and conformal mapping techniques to compute even- and odd-mode impedances in edge-coupled coplanar waveguide (CPW) structures. Its versatility allows application to both planar and 3-D heterogeneous architectures, making it a powerful tool for resonator design. To validate the model, a test chip with λ/4 resonators of varying geometries is fabricated and measured in a cryogenic environment. Comparisons with finite element method (FEM) simulations and experimental measurements confirm the model's accuracy, with resonance frequencies and coupling Q-factors aligning closely across configurations. This proposed model facilitates the design of superconducting resonators in readout circuits for more effective, scalable, and adaptable quantum computing architectures.
In this paper, we present a novel design of a compact, double-fold half-wave superconducting coplanar waveguide resonator, specifically optimized for quantum readout. The geometry offers advantages in terms of scalability and allows for a more compact integration of qubits per unit area. The superconducting resonators are designed to operate within a fundamental frequency range of 1.9 GHz$-1.95GHz,utilizingbothgapandfingercouplingschemes.Thedevicesarefabricatedusingthinaluminumfilmsdepositedonhigh−resistivitysapphiresubstrates.Theproposedresonatorsexhibitqualityfactor(Q1.95 GHz, utilizing both gap and finger coupling schemes. The devices are fabricated using thin aluminum films deposited on high-resistivity sapphire substrates. The proposed resonators exhibit quality factor (Q1.95GHz,utilizingbothgapandfingercouplingschemes.Thedevicesarefabricatedusingthinaluminumfilmsdepositedonhigh−resistivitysapphiresubstrates.Theproposedresonatorsexhibitqualityfactor(Q_{L})of2.9×) of 2.9 ×)of2.9× 10^{5}$and 1.58 ×10310^{3}103for gap coupled and finger coupled, respectively, during experimental measurements. The simulated QL_{L}L​of single-folded meander line resonators are found to be 4.65 ×10510^{5}105and 258.42, for gap coupled and finger coupled, respectively, for comparison purpose at similar operating frequency. A comprehensive analysis of the microwave transmission spectra was conducted at cryogenic temperatures near 10 mK, across very high input drive powers ($-30dBmto30 dBm to30dBmto-10dBm).Experimentalresultsshowagoodagreementwithsimulationsandtheequivalentlumpedcircuitmodel.Notably,theproposeddesignreducesthephysicalfootprintoftheresonatordevicesupto28.210 dBm). Experimental results show a good agreement with simulations and the equivalent lumped circuit model. Notably, the proposed design reduces the physical footprint of the resonator devices up to 28.210dBm).Experimentalresultsshowagoodagreementwithsimulationsandtheequivalentlumpedcircuitmodel.Notably,theproposeddesignreducesthephysicalfootprintoftheresonatordevicesupto28.2\%comparedtoconventionalsingle−foldmeanderedstructures.TheresonatorsdemonstratestrongpotentialforintegratingqubitswithreadoutandcontrolbusesinquantuminformationprocessingwhichrequireaQcompared to conventional single-fold meandered structures. The resonators demonstrate strong potential for integrating qubits with readout and control buses in quantum information processing which require a Qcomparedtoconventionalsingle−foldmeanderedstructures.TheresonatorsdemonstratestrongpotentialforintegratingqubitswithreadoutandcontrolbusesinquantuminformationprocessingwhichrequireaQ_{L}$between10410^{4}104−-−10510^{5}105. They also being well-suited for cryogenic detector applications that utilize microwave kinetic inductance detector (MKID) arrays in frequency multiplexing for different coupling schemes.