Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1706.04169 · AIP Advances

Characterization of low loss microstrip resonators as a building block for circuit QED in a 3D waveguide

D. Zoepfl, P. R. Muppalla, C. M. F. Schneider, S. Kasemann, Stefan Partel, Gerhard Kirchmair

Published Aug 1, 2017• 17 citations
arXivHTMLPDF

Abstract

Here we present the microwave characterization of microstrip resonators, made from aluminum and niobium, inside a 3D microwave waveguide. In the low temperature, low power limit internal quality factors of up to one million were reached. We found a good agreement to models predicting conductive losses and losses to two level systems for increasing temperature. The setup presented here is appealing for testing materials and structures, as it is free of wire bonds and offers a well controlled microwave environment. In combination with transmon qubits, these resonators serve as a building block for a novel circuit QED architecture inside a rectangular waveguide.

DOI
10.1063/1.4992070

Related papers

Characterizing the attenuation of coaxial and rectangular microwave-frequency waveguides at cryogenic temperatures

Philipp Kurpiers, Theodore Walter, Paul Magnard +2 more

Low-loss waveguides are required for quantum communication at distances beyond the chip-scale for any low-temperature solid-state implementation of quantum information processors. We measure and analyze the attenuation constant of commercially available microwave-frequency waveguides down to millikelvin temperatures and single photon levels. More specifically, we characterize the frequency-dependent loss of a range of coaxial and rectangular microwave waveguides down to $0.005\ \mbox{dB}/\mbox{m}$ using a resonant-cavity technique. We study the loss tangent and relative permittivity of commonly used dielectric waveguide materials by measurements of the internal quality factors and their comparison with established loss models. The results of our characterization are relevant for accurately predicting the signal levels at the input of cryogenic devices, for reducing the loss in any detection chain, and for estimating the heat load induced by signal dissipation in cryogenic systems.

arXiv:1612.07977•EPJ Quantum Technology•May 4, 2017•52 citations

Power-dependence measurement of the quality factor of superconducting microwave resonators at mK temperature

Seon Hoo Kim, Dong-Gwang Ha, Gwan Yeol Park +7 more

We report our setup and measurement results of the quality factor Q of superconducting microwave resonators at mK temperature in a dilution refrigerator. The power dependence of the superconducting resonators' Q was measured down to the single photon level. Measurements were performed on two types of microwave resonators. First, a half-wavelength coplanar waveguide (CPW) resonator made of niobium film on an oxidized high-resistivity silicon substrate was measured. Then a rectangular box resonator made of machined superconducting aluminum alloy was measured. While the CPW chip resonator's Q value showed noticeable decrease at low microwave power, the box resonator's Q showed little power dependence. This setup is intended to perform characterization of various microwave resonators, which will serve as key components in superconducting qubit in circuit QED architecture.

Conference on Precision Electromagnetic Measurements•Aug 1, 2014•2 citations

Development of high quality superconducting resonators for quantum device applications

Dong-Gwang Ha, Seon Hoo Kim, So-Yeon Jun +5 more

We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.

IEEE International Superconductive Electronics Conference (ISEC)•Jul 1, 2013•0 citations

Coplanar waveguide resonators for circuit quantum electrodynamics

M. Göppl, A. Fragner, Matthias Baur +7 more

High quality on-chip microwave resonators have recently found prominent new applications in quantum optics and quantum information processing experiments with superconducting electronic circuits, a field now known as circuit quantum electrodynamics (QED). They are also used as single photon detectors and parametric amplifiers. Here we analyze the physical properties of coplanar waveguide resonators and their relation to the materials properties for use in circuit QED. We have designed and fabricated resonators with fundamental frequencies from 2 to 9 GHz and quality factors ranging from a few hundreds to a several hundred thousands controlled by appropriately designed input and output coupling capacitors. The microwave transmission spectra measured at temperatures of 20 mK are shown to be in good agreement with theoretical lumped element and distributed element transmission matrix models. In particular, the experimentally determined resonance frequencies, quality factors, and insertion losses are fully and consistently explained by the two models for all measured devices. The high level of control and flexibility in design renders these resonators ideal for storing and manipulating quantum electromagnetic fields in integrated superconducting electronic circuits.

arXiv:0807.4094•Journal of Applied Physics•Dec 1, 2008•402 citations

Planar superconducting resonators with internal quality factors above one million

A. Megrant, C. Neill, R. Barends +16 more

We describe the fabrication and measurement of microwave coplanar waveguide resonators with internal quality factors above 107 at high microwave powers and over 106 at low powers, with the best low power results approaching 2×106, corresponding to ∼1 photon in the resonator. These quality factors are achieved by controllably producing very smooth and clean interfaces between the resonators’ aluminum metallization and the underlying single crystal sapphire substrate. Additionally, we describe a method for analyzing the resonator microwave response, with which we can directly determine the internal quality factor and frequency of a resonator embedded in an imperfect measurement circuit.

arXiv:1201.3384•Applied Physics Letters•Mar 12, 2012•499 citations

Utilization of the superconducting transition for characterizing low-quality-factor superconducting resonators

Yu-Cheng Chang, Bayan Karimi, Jorden Senior +5 more

Characterizing superconducting microwave resonators with highly dissipative elements is a technical challenge, but a requirement for implementing and understanding the operation of hybrid quantum devices involving dissipative elements, e.g., for thermal engineering and detection. We present experiments on λ/4 superconducting niobium coplanar waveguide resonators, terminating at the antinode by a dissipative copper microstrip via aluminum leads, such that the resonator response is difficult to measure in a typical microwave environment. By measuring the transmission both above and below the superconducting transition of aluminum, we are able to isolate the resonance. We then experimentally verify this method with copper microstrips of increasing thicknesses, from 50 nm to 150 nm, and measure quality factors in the range of 10–67 in a consistent way.

arXiv:1904.01781•Applied Physics Letters•Jul 8, 2019•7 citations
Here we present the microwave characterization of microstrip resonators, made from aluminum and niobium, inside a 3D microwave waveguide. In the low temperature, low power limit internal quality factors of up to one million were reached. We found a good agreement to models predicting conductive losses and losses to two level systems for increasing temperature. The setup presented here is appealing for testing materials and structures, as it is free of wire bonds and offers a well controlled microwave environment. In combination with transmon qubits, these resonators serve as a building block for a novel circuit QED architecture inside a rectangular waveguide.
Low-loss waveguides are required for quantum communication at distances beyond the chip-scale for any low-temperature solid-state implementation of quantum information processors. We measure and analyze the attenuation constant of commercially available microwave-frequency waveguides down to millikelvin temperatures and single photon levels. More specifically, we characterize the frequency-dependent loss of a range of coaxial and rectangular microwave waveguides down to $0.005\ \mbox{dB}/\mbox{m}$ using a resonant-cavity technique. We study the loss tangent and relative permittivity of commonly used dielectric waveguide materials by measurements of the internal quality factors and their comparison with established loss models. The results of our characterization are relevant for accurately predicting the signal levels at the input of cryogenic devices, for reducing the loss in any detection chain, and for estimating the heat load induced by signal dissipation in cryogenic systems.
We report our setup and measurement results of the quality factor Q of superconducting microwave resonators at mK temperature in a dilution refrigerator. The power dependence of the superconducting resonators' Q was measured down to the single photon level. Measurements were performed on two types of microwave resonators. First, a half-wavelength coplanar waveguide (CPW) resonator made of niobium film on an oxidized high-resistivity silicon substrate was measured. Then a rectangular box resonator made of machined superconducting aluminum alloy was measured. While the CPW chip resonator's Q value showed noticeable decrease at low microwave power, the box resonator's Q showed little power dependence. This setup is intended to perform characterization of various microwave resonators, which will serve as key components in superconducting qubit in circuit QED architecture.
We report our development on design, fabrication and characterization of various superconducting resonators for quantum device applications. The resonators are developed mainly for superconducting qubit implementation in circuit QED structure, but future application will include photon detectors such as microwave kinetic inductance detectors. First we designed and fabricated half-wavelength coplanar waveguide resonators with niobium thin film on a high resistive silicon wafer, with the fundamental frequencies in the range of 1 to 8 GHz. The loaded quality factors are controlled by the coupling capacitors, and the lower bound of the intrinsic quality factor was measured down to 7 mK in the dilution refrigerator. We have also designed quarter-wavelength resonators and lumped LC resonators coupled to a transmission line, and characterized multiple resonators in a single transmission line. For the 3D transmon qubit application, we designed and fabricated a rectangular box resonator with superconducting aluminum. The intrinsic quality factor of the box resonator exceeds three million at 7 mK. We will also present basic results on the integration of a transmon qubit in the superconducting resonator.
High quality on-chip microwave resonators have recently found prominent new applications in quantum optics and quantum information processing experiments with superconducting electronic circuits, a field now known as circuit quantum electrodynamics (QED). They are also used as single photon detectors and parametric amplifiers. Here we analyze the physical properties of coplanar waveguide resonators and their relation to the materials properties for use in circuit QED. We have designed and fabricated resonators with fundamental frequencies from 2 to 9 GHz and quality factors ranging from a few hundreds to a several hundred thousands controlled by appropriately designed input and output coupling capacitors. The microwave transmission spectra measured at temperatures of 20 mK are shown to be in good agreement with theoretical lumped element and distributed element transmission matrix models. In particular, the experimentally determined resonance frequencies, quality factors, and insertion losses are fully and consistently explained by the two models for all measured devices. The high level of control and flexibility in design renders these resonators ideal for storing and manipulating quantum electromagnetic fields in integrated superconducting electronic circuits.
We describe the fabrication and measurement of microwave coplanar waveguide resonators with internal quality factors above 107 at high microwave powers and over 106 at low powers, with the best low power results approaching 2×106, corresponding to ∼1 photon in the resonator. These quality factors are achieved by controllably producing very smooth and clean interfaces between the resonators’ aluminum metallization and the underlying single crystal sapphire substrate. Additionally, we describe a method for analyzing the resonator microwave response, with which we can directly determine the internal quality factor and frequency of a resonator embedded in an imperfect measurement circuit.
Characterizing superconducting microwave resonators with highly dissipative elements is a technical challenge, but a requirement for implementing and understanding the operation of hybrid quantum devices involving dissipative elements, e.g., for thermal engineering and detection. We present experiments on λ/4 superconducting niobium coplanar waveguide resonators, terminating at the antinode by a dissipative copper microstrip via aluminum leads, such that the resonator response is difficult to measure in a typical microwave environment. By measuring the transmission both above and below the superconducting transition of aluminum, we are able to isolate the resonance. We then experimentally verify this method with copper microstrips of increasing thicknesses, from 50 nm to 150 nm, and measure quality factors in the range of 10–67 in a consistent way.