Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1609.02653 · Physical Review A

Experimental demonstration of passive-decoy-state quantum key distribution with two independent lasers

Shi‐Hai Sun, Guang‐Zhao Tang, Chunyan Li, Lin-Mei Liang

Published Sep 27, 2016• 15 citations
arXivHTMLPDF

Abstract

The decoy-state method could effectively enhance the performance of quantum key distribution (QKD) with a practical phase randomized weak coherent source. Although active modulation of the source intensity is effective and has been implemented in many experiments, passive preparation of decoy states is also an important addition to the family of decoy-state QKD protocols. In this paper, following the theory of Curty et al. [Phys. Rev. A 81, 022310 (2010)], we experimentally demonstrate the phase-encoding passive-decoy-state QKD with only linear optical setups and threshold single-photon detectors. In our experiment, two homemade independent pulsed lasers, with visibility of Hong-Ou-Mandel interference $0.53(\ifmmode\pm\else\textpm\fi{}0.003)$, have been implemented and used to passively generate the different decoy states. Finally, a secret key rate of $1.5\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}5}$/pulse is obtained with 10-km commercial fiber between Alice and Bob.

DOI
10.1103/physreva.94.032324

Related papers

Passive decoy-state quantum key distribution with practical light sources

Marcos Curty, Xiongfeng Ma, Bing Qi +1 more

Decoy states have been proven to be a very useful method for significantly enhancing the performance of quantum key distribution systems with practical light sources. Although active modulation of the intensity of the laser pulses is an effective way of preparing decoy states in principle, in practice passive preparation might be desirable in some scenarios. Typical passive schemes involve parametric down-conversion. More recently, it has been shown that phase-randomized weak coherent pulses (WCP) can also be used for the same purpose [M. Curty et al., Opt. Lett. 34, 3238 (2009).] This proposal requires only linear optics together with a simple threshold photon detector, which shows the practical feasibility of the method. Most importantly, the resulting secret key rate is comparable to the one delivered by an active decoy-state setup with an infinite number of decoy settings. In this article we extend these results, now showing specifically the analysis for other practical scenarios with different light sources and photodetectors. In particular, we consider sources emitting thermal states, phase-randomized WCP, and strong coherent light in combination with several types of photodetectors, like, for instance, threshold photon detectors, photon number resolving detectors, and classical photodetectors. Our analysis includes as well the effect that detection inefficiencies and noise in the form of dark counts shown by current threshold detectors might have on the final secret key rate. Moreover, we provide estimations on the effects that statistical fluctuations due to a finite data size can have in practical implementations.

arXiv:0911.2815•Physical Review A•Feb 10, 2010•82 citations

Experimental passive decoy-state quantum key distribution

Qi-Chao Sun, Weilong Wang, Yang Liu +8 more

The decoy-state method is widely used in practical quantum key distribution systems to replace ideal single photon sources with realistic light sources by varying intensities. Instead of active modulation, the passive decoy-state method employs built-in decoy states in a parametric down-conversion photon source, which can decrease the side channel information leakage in decoy state preparation and hence increase the security. By employing low dark count up-conversion single photon detectors, we have experimentally demonstrated the passive decoy-state method over a 50-km-long optical fiber and have obtained a key rate of about 100 bit/s. Our result suggests that the passive decoy-state source is a practical candidate for future quantum communication implementation.

arXiv:1405.3761•Laser Physics Letters•Jun 19, 2014•27 citations

Passive Decoy-State Quantum Key Distribution with Coherent Light

Marcos Curty, Marc Jofre, Valerio Pruneri +1 more

Signal state preparation in quantum key distribution schemes can be realized using either an active or a passive source. Passive sources might be valuable in some scenarios; for instance, in those experimental setups operating at high transmission rates, since no externally driven element is required. Typical passive transmitters involve parametric down-conversion. More recently, it has been shown that phase-randomized coherent pulses also allow passive generation of decoy states and Bennett–Brassard 1984 (BB84) polarization signals, though the combination of both setups in a single passive source is cumbersome. In this paper, we present a complete passive transmitter that prepares decoy-state BB84 signals using coherent light. Our method employs sum-frequency generation together with linear optical components and classical photodetectors. In the asymptotic limit of an infinite long experiment, the resulting secret key rate (per pulse) is comparable to the one delivered by an active decoy-state BB84 setup with an infinite number of decoy settings.

arXiv:1108.0841•Entropy•Jun 12, 2015•12 citations

Quantum key distribution with distinguishable decoy states

Anqi Huang, Shi‐Hai Sun, Zhihong Liu +1 more

The decoy-state protocol has been considered to be one of the most important methods to protect the security of quantum key distribution (QKD) with a weak coherent source. Here we test two experimental approaches to generating the decoy states with different intensities: modulation of the pump current of a semiconductor laser diode, and external modulation by an optical intensity modulator. The former approach shows a side channel in the time domain that allows an attacker to distinguish s signal state from a decoy state, breaking a basic assumption in the protocol. We model a photon-number-splitting attack based on our experimental data, and show that it compromises the system's security. Then, based on the work of Tamaki et al. [New J. Phys. 18, 065008 (2016)], we obtain two analytical formulas to estimate the yield and error rate of single-photon pulses when the signal and decoy states are distinguishable. The distinguishability reduces the secure key rate below that of a perfect decoy-state protocol. To mitigate this reduction, we propose to calibrate the transmittance of the receiver (Bob's) unit. We apply our method to three QKD systems and estimate their secure key rates.

arXiv:1711.00597•Physical Review A•Jul 27, 2018•100 citations

Intensity correlations in decoy-state BB84 quantum key distribution systems

Daniil Trefilov, Xoel Sixto, Víctor Zapatero +3 more

The decoy-state method is a prominent approach to enhance the performance of quantum key distribution (QKD) systems that operate with weak coherent laser sources. Due to the limited transmissivity of single photons in optical fiber, current experimental decoy-state QKD setups increase their secret key rate by raising the repetition rate of the transmitter. However, this usually leads to correlations between subsequent optical pulses. This phenomenon leaks information about the encoding settings, including the intensities of the generated signals, which invalidates a basic premise of decoy-state QKD. Here we characterize intensity correlations between the emitted optical pulses in two industrial prototypes of decoy-state BB84 QKD systems and show that they significantly reduce the asymptotic key rate. In contrast to what has been conjectured, we experimentally confirm that the impact of higher-order correlations on the intensity of the generated signals can be much higher than that of nearest-neighbor correlations.

arXiv:2411.00709•Optica Quantum•Jul 15, 2025•14 citations

A Simple Scheme for Realizing the Passive Decoy-State Quantum Key Distribution

Chunhui Zhang, Dong Wang, Chun-Mei Zhang +1 more

In this paper, we present a scheme on realizing the passive decoy-state quantum key distribution. In this scheme, two weak coherent pulses interfere at a beam-splitter, and pulses in one output port are split by one beam-splitter into two parts which are sent into two local detectors individually. Then, all the clicking and nonclicking events from the local detectors are used to herald the arriving and nonarriving of the signal pulse in the other output port. Accordingly, we can obtain more decoy states in the photon-number space and can thus, achieve more precise estimations for single-photon contributions. In this scheme, we use only one intensity at each input of the beam-splitter to avoid intensity modulation fluctuations existing in other active decoy-state methods. We compare the present scheme with Curty et al.'s passive scheme and the conventional three-intensity decoy-state scheme with the weak coherent sources. Through numerical simulations, we demonstrate that this scheme is better than the other two methods.

Journal of Lightwave Technology•Apr 13, 2018•5 citations
The decoy-state method could effectively enhance the performance of quantum key distribution (QKD) with a practical phase randomized weak coherent source. Although active modulation of the source intensity is effective and has been implemented in many experiments, passive preparation of decoy states is also an important addition to the family of decoy-state QKD protocols. In this paper, following the theory of Curty et al. [Phys. Rev. A 81, 022310 (2010)], we experimentally demonstrate the phase-encoding passive-decoy-state QKD with only linear optical setups and threshold single-photon detectors. In our experiment, two homemade independent pulsed lasers, with visibility of Hong-Ou-Mandel interference 0.53(\ifmmode±\else\textpm\fi0.003)0.53(\ifmmode\pm\else\textpm\fi{}0.003)0.53(\ifmmode±\else\textpm\fi0.003), have been implemented and used to passively generate the different decoy states. Finally, a secret key rate of 1.5\ifmmode×\else\texttimes\fi10\ensuremath−51.5\ifmmode\times\else\texttimes\fi{}{10}^{\ensuremath{-}5}1.5\ifmmode×\else\texttimes\fi10\ensuremath−5/pulse is obtained with 10-km commercial fiber between Alice and Bob.
Decoy states have been proven to be a very useful method for significantly enhancing the performance of quantum key distribution systems with practical light sources. Although active modulation of the intensity of the laser pulses is an effective way of preparing decoy states in principle, in practice passive preparation might be desirable in some scenarios. Typical passive schemes involve parametric down-conversion. More recently, it has been shown that phase-randomized weak coherent pulses (WCP) can also be used for the same purpose [M. Curty et al., Opt. Lett. 34, 3238 (2009).] This proposal requires only linear optics together with a simple threshold photon detector, which shows the practical feasibility of the method. Most importantly, the resulting secret key rate is comparable to the one delivered by an active decoy-state setup with an infinite number of decoy settings. In this article we extend these results, now showing specifically the analysis for other practical scenarios with different light sources and photodetectors. In particular, we consider sources emitting thermal states, phase-randomized WCP, and strong coherent light in combination with several types of photodetectors, like, for instance, threshold photon detectors, photon number resolving detectors, and classical photodetectors. Our analysis includes as well the effect that detection inefficiencies and noise in the form of dark counts shown by current threshold detectors might have on the final secret key rate. Moreover, we provide estimations on the effects that statistical fluctuations due to a finite data size can have in practical implementations.
The decoy-state method is widely used in practical quantum key distribution systems to replace ideal single photon sources with realistic light sources by varying intensities. Instead of active modulation, the passive decoy-state method employs built-in decoy states in a parametric down-conversion photon source, which can decrease the side channel information leakage in decoy state preparation and hence increase the security. By employing low dark count up-conversion single photon detectors, we have experimentally demonstrated the passive decoy-state method over a 50-km-long optical fiber and have obtained a key rate of about 100 bit/s. Our result suggests that the passive decoy-state source is a practical candidate for future quantum communication implementation.
Signal state preparation in quantum key distribution schemes can be realized using either an active or a passive source. Passive sources might be valuable in some scenarios; for instance, in those experimental setups operating at high transmission rates, since no externally driven element is required. Typical passive transmitters involve parametric down-conversion. More recently, it has been shown that phase-randomized coherent pulses also allow passive generation of decoy states and Bennett–Brassard 1984 (BB84) polarization signals, though the combination of both setups in a single passive source is cumbersome. In this paper, we present a complete passive transmitter that prepares decoy-state BB84 signals using coherent light. Our method employs sum-frequency generation together with linear optical components and classical photodetectors. In the asymptotic limit of an infinite long experiment, the resulting secret key rate (per pulse) is comparable to the one delivered by an active decoy-state BB84 setup with an infinite number of decoy settings.
The decoy-state protocol has been considered to be one of the most important methods to protect the security of quantum key distribution (QKD) with a weak coherent source. Here we test two experimental approaches to generating the decoy states with different intensities: modulation of the pump current of a semiconductor laser diode, and external modulation by an optical intensity modulator. The former approach shows a side channel in the time domain that allows an attacker to distinguish s signal state from a decoy state, breaking a basic assumption in the protocol. We model a photon-number-splitting attack based on our experimental data, and show that it compromises the system's security. Then, based on the work of Tamaki et al. [New J. Phys. 18, 065008 (2016)], we obtain two analytical formulas to estimate the yield and error rate of single-photon pulses when the signal and decoy states are distinguishable. The distinguishability reduces the secure key rate below that of a perfect decoy-state protocol. To mitigate this reduction, we propose to calibrate the transmittance of the receiver (Bob's) unit. We apply our method to three QKD systems and estimate their secure key rates.
The decoy-state method is a prominent approach to enhance the performance of quantum key distribution (QKD) systems that operate with weak coherent laser sources. Due to the limited transmissivity of single photons in optical fiber, current experimental decoy-state QKD setups increase their secret key rate by raising the repetition rate of the transmitter. However, this usually leads to correlations between subsequent optical pulses. This phenomenon leaks information about the encoding settings, including the intensities of the generated signals, which invalidates a basic premise of decoy-state QKD. Here we characterize intensity correlations between the emitted optical pulses in two industrial prototypes of decoy-state BB84 QKD systems and show that they significantly reduce the asymptotic key rate. In contrast to what has been conjectured, we experimentally confirm that the impact of higher-order correlations on the intensity of the generated signals can be much higher than that of nearest-neighbor correlations.
In this paper, we present a scheme on realizing the passive decoy-state quantum key distribution. In this scheme, two weak coherent pulses interfere at a beam-splitter, and pulses in one output port are split by one beam-splitter into two parts which are sent into two local detectors individually. Then, all the clicking and nonclicking events from the local detectors are used to herald the arriving and nonarriving of the signal pulse in the other output port. Accordingly, we can obtain more decoy states in the photon-number space and can thus, achieve more precise estimations for single-photon contributions. In this scheme, we use only one intensity at each input of the beam-splitter to avoid intensity modulation fluctuations existing in other active decoy-state methods. We compare the present scheme with Curty et al.'s passive scheme and the conventional three-intensity decoy-state scheme with the weak coherent sources. Through numerical simulations, we demonstrate that this scheme is better than the other two methods.