Abstract We demonstrate how dispersive atom number measurements during evaporative cooling can be used for enhanced determination of the parameter dependence of the transition to a Bose–Einstein condensate (BEC). In this way shot-to-shot fluctuations in initial conditions are detected and the information extracted per experimental realization is increased. We furthermore calibrate in situ images from dispersive probing of a BEC with corresponding absorption images in time-of-flight. This allows for the determination of the transition point in a single experimental realization by applying multiple dispersive measurements. Finally, we explore the continuous probing of several consecutive phase transition crossings using the periodic addition of a focused ‘dimple’ potential.
Abstract We demonstrate how dispersive atom number measurements during evaporative cooling can be used for enhanced determination of the parameter dependence of the transition to a Bose–Einstein condensate (BEC). In this way shot-to-shot fluctuations in initial conditions are detected and the information extracted per experimental realization is increased. We furthermore calibrate in situ images from dispersive probing of a BEC with corresponding absorption images in time-of-flight. This allows for the determination of the transition point in a single experimental realization by applying multiple dispersive measurements. Finally, we explore the continuous probing of several consecutive phase transition crossings using the periodic addition of a focused ‘dimple’ potential.
We wish to determine the heat capacity of a Bose-Einstein condensate (BEC) of ⁸⁷Rb atoms. Following the proposal of Blakie et al. [1], we consider the BEC to initially be in a state at zero temperature. We then transfer a known amount of energy to the condensate in such a way that it can be directly related to the internal energy of the resulting system. The thermal fraction of the system can be readily determined by absorption imaging, and hence the resulting temperature can be found. In order to form a BEC, the rubidium atoms are loaded from a magnetooptical trap into a dipole trap formed at the focal point of two intersecting CO₂ laser beams inside a vacuum chamber. The atoms then undergo the process of evaporative cooling in order to form a BEC. Once the BEC is formed we ramp up the power of the trap before beginning the process of imparting energy to the condensate. The dipole trap is turned off and the BEC is allowed to fall under the influence of gravity. After a specific period of time, usually in the order of 100-1000us, the dipole trap is reinstated. The system is then allowed to evolve in order for thermal equilibrium to be established. Finally the system is released from the trap and imaged using absorption imaging techniques. The images obtained during the experiment are fitted with a 2-dimensional model using a nonlinear regression method in MATLAB. From these fits we can extract the number of atoms in each shot, as well as the temperature of each one. The amount of energy transferred to the system is shown by Blakie et al. [1] and takes into account the effect of time dependant trap frequencies. This energy (Etrans), combined with the amount of energy transferred to the system while the trap is turned off (Edrop), gives the total energy transferred to the system and available for rethermalisation (Etotal). The heat capacity of the system is then simply given as Etotal=T.
Phase contrast imaging is used to observe Bose-Einstein condensates (BECs) at finite temperature in situ. The imaging technique is used to accurately derive the absolute phase shift of a probe laser beam due to both the condensate and the thermal cloud. The accuracy of the method is enhanced by using the periodicity of the intensity signal as a function of the accumulated phase. The measured density profiles can be described using a two relevant parameter fit, in which only the chemical potential and the temperature are to be determined. This allows us to directly compare the measured density profiles to different mean-field models in which the interaction between the condensed and thermal atoms is taken into account to various degrees.
We report dispersive spin shot noise measurement of a Bose-Einstein condensate (BEC). While dispersive probing has been used for quantum spin noise measurement of thermal and cold gases for decades, confirmative measurement of shot noise of real spin, i.e., the linear dependence of the spin variance on the number of atoms in a BEC, has been lacking. Here, we demonstrate precise spin noise measurement of a BEC of rubidium atoms at the spin shot noise level by polarization rotation using a two-color probe at optimal detunings, with power balance stabilization to suppress probe-induced excess spin noise. This work opens the possibility for the unexplored study of quantum spin fluctuations in multicomponent or spinor BECs and offers an approach to improve spin measurement precision, which is relevant to atomic spin-based sensors.
The achievement of Bose–Einstein condensation (BEC) in our experiment is reported. The process of BEC formation is observed by detecting the image after free expansion, in which the effectiveness of runaway evaporative cooling is shown by measuring the optical density of the atom cloud. About 2 × 10 5 87 Rb atoms in the | F = 2, m F = 2⟩ state are condensed into the condensate. The ratio of axial-to-radial size of the condensate released from the magnetic trap is investigated in theory and experiment.
Bose-Einstein condensation (BEC) in dilute gases stands as a fascinating phenomenon of quantum mechanics. In this state, hundreds of thousands of atoms occupy the lowest energy level, establishing a collective macroscopic quantum state, with numerous intriguing properties. BEC has become a fundamental tool for the exploration of quantum physics and it may facilitate further advancements in quantum technology, for instance, in quantum simulation and sensing applications. Due to the potential of BECs in both basic research and technology, a fundamental understanding of this phenomenon is essential to guarantee the precision and reliability of its applications. Atom number fluctuations in BECs stand as an unresolved fundamental problem that has posed significant theoretical challenges for nearly eight decades. The experimental observation of this effect has recently become feasible. However, a direct comparison between theoretical predictions and experimental results remains outstanding. In particular, technical challenges persist in the accurate detection of the BEC, and a thorough understanding of estimation errors is lacking. This PhD thesis addresses some of these challenges in the field. Firstly, it introduces an enhanced calibration method for time-of-flight absorption images of ultracold atomic clouds, improving the accuracy of such measurements. Additionally, a thorough statistical analysis of uncertainties in the preparation and parameter estimation of partially condensed Bose gases is presented, leading to an improved understanding of atom number fluctuations in BEC. Finally, this thesis presents the experimental advances toward a new project within the research group: Electromagnetically induced transparency (EIT). EIT is a concept where an otherwise opaque cloud can be made transparent through manipulation of its quantum states. Notably, these advancements include the construction of setups for an optical dipole trap and a hybrid trap, along with the development of systems enabling precise control of magnetic fields. This laid the groundwork for recent demonstrations of EIT within the group.
Summary form only given. We have systematically studied BECs of /sup 87/Rb atoms in the regime of phase-fluctuating condensates. We observe the phase fluctuations by measuring the density distribution of the released cloud after ballistic expansion. By varying the temperature, the number of atoms in the condensate and the aspect ratio of the trapping potential, we studied the continuous transition from the usual 3D regime, where phase fluctuations are low, into the regime of strong phase fluctuations in the condensate. To determine the amount of phase fluctuations experimentally, we measured the formation and structure of stripes in the atomic density distribution after ballistic expansion as a function of the above mentioned parameters. The appearance of stripes after switching off the trapping fields can be understood as conversion of phase fluctuations respect. phase gradients into axial velocity fields and consecutive density distributions. These results are in good agreement with theoretical and numerical studies and set clear limitations on applications of BECs e.g. in interferometric measurements.