Interference between independent photon sources is the key technique to realize complex quantum systems for more sophisticated applications such as multi-photon entanglement generation and quantum teleportation. Here, we report Hong-Ou-Mandel interference (HOMI) between two independent 1.55 m all-fiber photon pair sources over two 100 GHz dense wave division multiplexing (DWDM) channels, whose visibility reaches 53.2%8.4% (82.9%5.3%) without (with) back ground counts subtracted. In addition, we theoretically describe in detail the single photon spectral purity of the photon source generated in dispersion shifted fiber (DSF), simulate the influences of the pulse width and filter bandwidth on the purity, and obtain the optimized condition. The optimized pump pulse width is 8 ps and filter bandwidth is about 40 GHz or less. A home-made 1550.1 nm mode-locked fiber laser source, whose pulse width and repetition rate are 25 ps and 27.9 MHz respectively, acts as a pump of photon source. A tunable attenuator is used to adjust the pump power of the photon source, and the broad band background fluorescence photons are filtered out by cascade 100 GHz DWDM filters. The clean pump beam is divided into two equal parts by the 50 : 50 optical coupler to pump two 300 m DSFs (cooled by liquid nitrogen) to generate independent photon sources. Then the strong pump beam and noise photon from Raman scattering in orthogonal polarization are removed by 2 groups of 200 GHz DWDM filters and fiber polarization rotator and polarizer. Then two 100 GHz DWDMs are used for separating photons at correlated channel pairs. The relative delay between the two independent photons is adjusted by tunable fiber delay line. Photons from the same channels are combined in a second beam splitter for interference, and the other two photons are used as trigger signals. The two triggered photons are detected by two free running InGaAs avalanched single photon detectors (APD1, APD4, ID Quanta, ID220, 20% detection efficiency, 3 s dead time, dark count rate 4k cps), and the outputs of detectors APD1 and APD4 are used to trigger two single-photon detectors running in the gated mode (APD2, APD3, Qasky, Hefei, China, 100 MHz, free gating single photon detectors, 20% detection efficiency, dark count probability 410-5 per gate) for twophoton coincidence measurement. Detection output signals from APD2 and APD3 are sent to our coincidence count device (Pico quanta, TimeHarp 260, 1.6 ns coincidence window) for four-photon coincidence measurement. Before measuring the HOMI, we obtain a maximum-coincidence-to-accidental-coincidence ratio (CAR) of 131 by cooling the fiber in liquid nitrogen when the pump power is 23 W. There are a few remarks we want to point out.Firstly, the photon sources are not operated at the optimized pump pulse width for pure single photon generation, but narrow band 100 GHz filters are used in the experiments to increase the purity of the sources. Secondly, single photon detectors used in our experiment have lower detection efficiency and much higher dark counts than nano-wire single photon detectors, if we have high-performance nano-wire single photon detector, experimental results will be greatly improved due to the four-fold coincidences and dark coincidences scaling quadruplicate with the detection efficiency and dark count probability of a single detector. Thirdly, we use relatively high pump power for each DSF (0.12 mW) to reduce measurement time for photon coincidence, which will lead to a very poor raw visibility certainly. Finally, though only a 100 GHz channel pair is used in our experiment, we can use other channels for multiplexing such interference processes to improve the channel capacity in future quantum communication tasks theoretically. Our study shows greatly promising integrated optical elements for future scalable quantum information processing.
Interference between independent photon sources is the key technique to realize complex quantum systems for more sophisticated applications such as multi-photon entanglement generation and quantum teleportation. Here, we report Hong-Ou-Mandel interference (HOMI) between two independent 1.55 m all-fiber photon pair sources over two 100 GHz dense wave division multiplexing (DWDM) channels, whose visibility reaches 53.2%8.4% (82.9%5.3%) without (with) back ground counts subtracted. In addition, we theoretically describe in detail the single photon spectral purity of the photon source generated in dispersion shifted fiber (DSF), simulate the influences of the pulse width and filter bandwidth on the purity, and obtain the optimized condition. The optimized pump pulse width is 8 ps and filter bandwidth is about 40 GHz or less. A home-made 1550.1 nm mode-locked fiber laser source, whose pulse width and repetition rate are 25 ps and 27.9 MHz respectively, acts as a pump of photon source. A tunable attenuator is used to adjust the pump power of the photon source, and the broad band background fluorescence photons are filtered out by cascade 100 GHz DWDM filters. The clean pump beam is divided into two equal parts by the 50 : 50 optical coupler to pump two 300 m DSFs (cooled by liquid nitrogen) to generate independent photon sources. Then the strong pump beam and noise photon from Raman scattering in orthogonal polarization are removed by 2 groups of 200 GHz DWDM filters and fiber polarization rotator and polarizer. Then two 100 GHz DWDMs are used for separating photons at correlated channel pairs. The relative delay between the two independent photons is adjusted by tunable fiber delay line. Photons from the same channels are combined in a second beam splitter for interference, and the other two photons are used as trigger signals. The two triggered photons are detected by two free running InGaAs avalanched single photon detectors (APD1, APD4, ID Quanta, ID220, 20% detection efficiency, 3 s dead time, dark count rate 4k cps), and the outputs of detectors APD1 and APD4 are used to trigger two single-photon detectors running in the gated mode (APD2, APD3, Qasky, Hefei, China, 100 MHz, free gating single photon detectors, 20% detection efficiency, dark count probability 410-5 per gate) for twophoton coincidence measurement. Detection output signals from APD2 and APD3 are sent to our coincidence count device (Pico quanta, TimeHarp 260, 1.6 ns coincidence window) for four-photon coincidence measurement. Before measuring the HOMI, we obtain a maximum-coincidence-to-accidental-coincidence ratio (CAR) of 131 by cooling the fiber in liquid nitrogen when the pump power is 23 W. There are a few remarks we want to point out.Firstly, the photon sources are not operated at the optimized pump pulse width for pure single photon generation, but narrow band 100 GHz filters are used in the experiments to increase the purity of the sources. Secondly, single photon detectors used in our experiment have lower detection efficiency and much higher dark counts than nano-wire single photon detectors, if we have high-performance nano-wire single photon detector, experimental results will be greatly improved due to the four-fold coincidences and dark coincidences scaling quadruplicate with the detection efficiency and dark count probability of a single detector. Thirdly, we use relatively high pump power for each DSF (0.12 mW) to reduce measurement time for photon coincidence, which will lead to a very poor raw visibility certainly. Finally, though only a 100 GHz channel pair is used in our experiment, we can use other channels for multiplexing such interference processes to improve the channel capacity in future quantum communication tasks theoretically. Our study shows greatly promising integrated optical elements for future scalable quantum information processing.
Q uantum entanglement refers to the nonclassical dependency of physically separated quantum systems. It is an essential resource that must be freely available for implementing many of the novel functions of quantum information processing, such as database searching, clock synchronization, teleportation, computing and cryptography.1 The efficient generation and transmission of quantum entanglement is therefore of prime importance. With the ubiquitous standard optical fiber serving as the transmission medium and the widespread availability of efficient active and passive fiber devices, technological synergy between the generation and propagation components of the overall quantum network can be achieved by deploying sources of entanglement that rely on the nonlinearity of the fiber itself. Such fiber-based sources of quantum entanglement would also have the advantage of modal purity over their crystal counterparts,2,3 which is very important for realizing complex networks that involve many quantum operations. In our quest to develop fiber-based devices for quantum information processing, we have recently demonstrated an allfiber source of quantum-correlated photon pairs.4 The operating physical mechanism in this source is nondegenerate fourphoton mixing, wherein two pump photons scatter through the Kerr nonlinearity of the fiber to create simultaneous signal and idler photons. Our experiment is conducted near the zero-dispersion wavelength of standard dispersion-shifted fiber, where such scattering is enhanced owing to phase matching of the photon wave functions. It must be pointed out here that in a conventional wavelength-divisionmultiplexed classical optical communication line, one strives to suppress the fourphoton or four-wave mixing process, which otherwise causes cross talk between the wavelength channels and sets limits on the total data capacity of the communication line. In our experiment, the four-photon mixing takes place in a nonlinear-fiber Sagnac interferometer (NFSI), which we previously used to generate quantum-correlated twin beams in the fiber.5 The pump is a mode-locked train of ~3-ps-long pulses. The pulsed operation serves two important purposes: the NFSI amplifier can be operated at low average powers and the production of the signal/ idler fluorescence photons is confined to well-defined temporal windows, allowing use of a gated detection scheme to increase the signal-to-noise ratio. To measure the nonclassical (i.e., quantum) correlations between the signal and the idler photons, one must effectively suppress the pump photons from reaching the detectors. Since a typical pump pulse contains ~108 photons and we are interested in detecting ~0.01 signal (idler) photons/pulse, a pump-to-signal (idler) rejection ratio in excess of 100 dB is required. We achieved this specification by sending the fluorescence photons through a free-space double-grating spectral filter that separates the signal and idler photons from each other and from the pump photons not rejected by the NFSI. To demonstrate the quantum nature of the four-photon scattering at the single photon level, we assembled a photonFigure 1.C oincidence rates as a function of the single-photon rates in two different cases: signalidler fluorescence produced by a pump pulse (diamonds) and signal-idler fluorescence produced by two consecutive pump pulses (triangles). T he line represents the calculated accidental counts. T he inset shows a plot of the detected idler photons as a function of the injected pump photons (hollow circles). A second-order polynomial is shown to fit the experimental data. T he contributions of the dark counts, linear scattering and quadratic scattering are plotted separately as well. counting apparatus for detecting the signal and idler photons in coincidence. This apparatus is based on commercial InGaAs avalanche photodiodes operating in the gated Geiger mode.4 In the inset in Fig. 1, we show the number of scattered photons, NS, versus the number of pump photons, NP, injected into the NFSI. We fit the experimental data with a second-order polynomial fit, including the number of dark counts during the gate interval, ND. The fit clearly shows that the quadratic scattering ( ∝NP) in the fiber can dominate over the residual linear scattering ( ∝NP) of the pump, owing to imperfect filtering. The main body of Fig. 1 shows the coincidence-counting results. The diamonds represent the rate of coincidence counts versus the rate of the signal (idler) photons generated during the same pump pulse. The triangles represent the measured coincidence rate versus the signalphoton count rate when the signal is delayed with respect to the idler by one pulse period. For two independent photon sources, each with a count rate RS <<1, the accidental coincidence rate RC is given by RC = RS 2, regardless of the photon statistics of the sources. This quadratic relation is plotted as the solid line in Fig. 1, which fits the delayed-coincidence data (triangles) very well. These measurements show that while the fluorescence photons produced by the adjacent pump pulses are independent, those coming from the same pump pulse show a strong correlation, which is a signature of their non-classical behavior. This work was supported by the Department of Defense Multidisciplinary University Research Initiative program administered by the Army Research Office under Grants DAAD19-00-1-0177 and DAAD19-00-1-0469, and by the U.S. Office of Naval Research under Grant N00014-91-J-1268.
Hong-Ou-Mandel interference between independent photon sources (HOMI-IPS) plays an important role in quantum information processing. A variety of HOMI-IPS experiments have been demonstrated at near-infrared wavelengths or telecom wavelengths [1]. In all the previous HOMI-IPS experiments, the HOM dips are obtained by recording the four-fold coincidence counts as a function of the temporal delay. However, the spectral correlation during the interference is omitted, partially due to technical difficulties, e.g., the acquisition time is too long for measuring a joint spectral distribution. Spectral information, as the conjugate of the temporal information in the Fourier transformation, is definitely of great importance and should be investigated. Very recently, a new technique of spectral correlation measurement in a HOM interference has been developed by Gerrits, et al [2]. This technique has the merits of high speed and high resolution, therefore, has been used as a powerful tool to analyse the spectral correlation in a HOM interference between signal and idler photons from one spontaneous parametric down conversion (SPDC) source. In this work, we measure the joint spectral distribution in HOMI-IPS using the new technique developed in [2]. The experimental setup is shown in Fig. 1 (Left). The two independent sources are based on SPDC from two 30-mm-long periodically poled KTiOPO4 (PPKTP) crystals pumped by picosecond laser pulses (76 MHz, 792 nm, temporal duration ~ 2 ps). In Fig. 1 (Left), the dispersion compensation fiber model (DCFMs), the superconducting nanowire single-photon detectors (SNSPDs) [3,4,5] and the time interval analyzer (TIA) constitute a fiber spectral analyzer [6]. Fig. 1(Right: (a)) is the measured four-fold HOM interference between signal1 and signal2, with idler1 and idler2 as heralders. Without subtraction of any background counts, the raw visibility of the HOM dip is 69.9±3.2%, which is consistent with our previous results in [1,7,8]. Fig. 1(Right: (b)-(g)) are the measured joint spectral intensities at different delay positions. The splitting phenomenon in the joint spectral distribution is clearly observed. The experimental results agree well with our theoretical simulations. This experiment not only can deepen our understanding of HOMI-IPS from the viewpoint of spectral domain, but also can be used to improve the visibility of HOMI-IPS by temporal filtering.
Heralded single photons with wavelength near 1550nm are expected to be an important resource for future quantum communications applications. Such applications often rely on non-classical Hong Ou Mandel interference (HOMI) that is observed between indistinguishable, pure photon states. While high visibility HOMI is routinely achieved for photons from identically prepared sources, here we observe interference between photons from two dissimilar systems. To generate synchronised indistinguishable photons, two photon sources were pumped with a single 1064nm, picosecond-pulsed fibre laser. In one source the laser pulses generated correlated pairs of photons at 810nm and 1550nm through four-wave mixing in photonic crystal fibre (PCF). In the other, the laser was used to generate second harmonic light at 532nm in a bulk crystal, before being launched into a periodically poled lithium niobate (PPLN) waveguide. This structure was designed to generate signal and idler photons through parametric down-conversion, matched in wavelength to the fibre based source. Idler photons from both sources were input into a fused-fibre coupler in order to measure the HOMI visibility. HOMI with a net visibility of 70% was demonstrated between photons from the two sources (after accounting for the background due to emission of multiple photons from a single source). A visibility of 80% is anticipated for the current sources after further improvement in the purity of the generated states. This result is the first step towards realising a quantum relay system, in which transmitted qubits produced by low loss, fibre-based photon sources interact with photons produced locally on a chip.
We performed a Hong–Ou–Mandel interference experiment with 1.5 μm band photon pairs generated through spontaneous four-wave mixing (SFWM) in two independent silicon wire waveguides (SWWs). To maintain the long-term stability of the coupling between the SWWs and optical fibers without a fiber alignment system, we employed fiber module SWWs installed in a rigid metallic case with fiber array interfaces. In addition, those signal photons that passed through a beam splitter (BS) were detected by high-speed single-photon detectors that used InGaAs avalanche photodiodes operated in a gated mode with a high gate frequency of 500 MHz. With these novel technologies, we successfully observed a quantum interference with a visibility of 73% without subtracting accidental coincidence counts in the fourfold coincidence measurement.
The time-energy entangled photon source is a core resource in quantum key distribution, quantum teleportation, and quantum metrology. The output of orthogonally polarized photon pairs can enhance the effective coincidence counts of the entangled source in these applications. Additionally, an all-fiber entangled source offers small size and high mobility advantages. However, most current orthogonally polarized all-fiber time-energy entangled sources are limited to a bandwidth of around 1 nm, which is detrimental to the effective utilization of channel resources in fiber networks and restricts precision in quantum metrology. To address this issue, we employ a fiber-coupled 775 nm narrow linewidth pump laser in a periodically poled lithium niobate (PPLN) waveguide to achieve type-II spontaneous parametric down-conversion (SPDC). This results in an all-fiber orthogonally polarized time-energy entangled photon source with a bandwidth greater than 7 nm. We measured the single counts, coincidence counts, coincidence to accidental coincidence ratio (CAR), single photon spectra, and joint spectral intensity of the entangled source, calculating the Schmidt number S = 7.8. Furthermore, we measured Hong-Ou-Mandel (HOM) interference by inserting two 2 nm bandpass filters, and the interference visibility remained around 95.8% after continuous operation for 3 hours. The experimental results indicate that while maintaining an all-fiber structure, this source possesses a broadband range, low noise, and high stability, providing efficient and reliable biphoton resources for applications in quantum communication, quantum networks, and precision metrology.
Single photon sources (SPSs) play important roles in quantum communication and quantum information processing. Spontaneous four wave mixing (SFWM) in optical fibers provides a promising way to realize practical heralded single photon sources (HSPSs), since it is compatible with current techniques of optical communications. In this paper, two independent HSPSs at 1.5μm band are realized in one polarization maintaining dispersion shifted fiber (PM-DSF) utilizing its large birefringence. When pulsed pump light passes through an optical fiber, two kinds of SFWM will take place simultaneously. One is scalar processes, in which two annihilated pump photons and generated photon pair are all polarized along the same fiber polarization axis. The other is vector processes, in which two annihilated pump photons are polarized along different fiber polarization axes, either for the two photons of the generated pair. In the PM-DSF, the large birefringence generates obvious walk-off effect on the two pump polarization components, which leads to an effective suppression of the vector processes. Hence, by proper pump polarization, correlated photon pairs (CPPs) with different polarization directions can be generated independently by the two scalar processes, which can be used to realize two independent HSPSs. The indistinguishability of the heralded photons generated by the two independent sources is demonstrated by an experiment of Hong-Ou-Mandel (HOM) interference. Using a fiber coupler as the beam splitter, a visibility of HOM dip of 76% is achieved, showing their potential on quantum information.