Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1605.01351 · Physical Review Letters

Demonstration of Weight-Four Parity Measurements in the Surface Code Architecture

Maika Takita, Antonio D. Corcoles, Easwar Magesan, Baleegh Abdo, Markus Brink, Andrew W. Cross, Jerry M. Chow, Jay Gambetta

Published Nov 18, 2016• 201 citations
arXivHTMLPDF

Abstract

We present parity measurements on a five-qubit lattice with connectivity amenable to the surface code quantum error correction architecture. Using all-microwave controls of superconducting qubits coupled via resonators, we encode the parities of four data qubit states in either the X or the Z basis. Given the connectivity of the lattice, we perform a full characterization of the static Z interactions within the set of five qubits, as well as dynamical Z interactions brought along by single- and two-qubit microwave drives. The parity measurements are significantly improved by modifying the microwave two-qubit gates to dynamically remove nonideal Z errors.

DOI
10.1103/physrevlett.117.210505

Related papers

Characterizing a four-qubit planar lattice for arbitrary error detection

Jerry M. Chow, Srikanth J. Srinivasan, Easwar Magesan +4 more

Quantum error correction will be a necessary component towards realizing scalable quantum computers with physical qubits. Theoretically, it is possible to perform arbitrarily long computations if the error rate is below a threshold value. The two-dimensional surface code permits relatively high fault-tolerant thresholds at the ~1% level, and only requires a latticed network of qubits with nearest-neighbor interactions. Superconducting qubits have continued to steadily improve in coherence, gate, and readout fidelities, to become a leading candidate for implementation into larger quantum networks. Here we describe characterization experiments and calibration of a system of four superconducting qubits arranged in a planar lattice, amenable to the surface code. Insights into the particular qubit design and comparison between simulated parameters and experimentally determined parameters are given. Single- and two-qubit gate tune-up procedures are described and results for simultaneously benchmarking pairs of two-qubit gates are given. All controls are eventually used for an arbitrary error detection protocol described in separate work [Corcoles et al., Nature Communications, 6, 2015].

arXiv:1509.02815•Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•May 21, 2015•22 citations

Demonstration of a quantum error detection code using a square lattice of four superconducting qubits

Antonio D. Corcoles, Easwar Magesan, Srikanth J. Srinivasan +4 more

The ability to detect and deal with errors when manipulating quantum systems is a fundamental requirement for fault-tolerant quantum computing. Unlike classical bits that are subject to only digital bit-flip errors, quantum bits are susceptible to a much larger spectrum of errors, for which any complete quantum error-correcting code must account. Whilst classical bit-flip detection can be realized via a linear array of qubits, a general fault-tolerant quantum error-correcting code requires extending into a higher-dimensional lattice. Here we present a quantum error detection protocol on a two-by-two planar lattice of superconducting qubits. The protocol detects an arbitrary quantum error on an encoded two-qubit entangled state via quantum non-demolition parity measurements on another pair of error syndrome qubits. This result represents a building block towards larger lattices amenable to fault-tolerant quantum error correction architectures such as the surface code.

arXiv:1410.6419•Nature Communications•Apr 29, 2015•496 citations

Demonstration of dynamic surface codes

Alec Eickbusch, Matt McEwen, Volodymyr Sivak +97 more

A remarkable characteristic of quantum computing is the potential for reliable computation despite faulty qubits. This can be achieved through quantum error correction, which is typically implemented by repeatedly applying static syndrome checks, permitting correction of logical information. Recently, the development of time-dynamic approaches to error correction has enabled different codes and implementations that do not rely on static syndrome measurements. Here we experimentally demonstrate three time-dynamic implementations of the surface code, each offering a distinct solution to hardware design challenges faced by surface code realizations. First, we embed the surface code on a hexagonal lattice, reducing the necessary couplings per qubit from four to three. Second, we walk a surface code, swapping the role of data and measure qubits each round, achieving error correction with built-in removal of accumulated non-computational errors. Finally, we realize the surface code using iSWAP gates instead of the traditional CNOT, extending the set of viable gates for error correction without additional overhead. We measure the error suppression factor when scaling from distance-3 to distance-5 codes of Λ35,hex = 2.15(2), Λ35,walk = 1.69(6) and Λ35,iSWAP = 1.56(2), achieving state-of-the-art error suppression for each. Our work demonstrates that dynamic circuit approaches meet the demands for fault tolerance and enable alternative strategies for scalable hardware design. Typical quantum error correcting codes assign fixed roles to the underlying physical qubits. Now the performance benefits of alternative, dynamic error correction schemes have been demonstrated on a superconducting quantum processor.

arXiv:2412.14360•Nature Physics•Oct 17, 2025•71 citations

Weight-four parity checks with silicon spin qubits

Brennan Undseth, Nicola Meggiato, Yi-Hsien Wu +7 more

Recent advances in coherent spin shuttling have made sparse semiconductor spin qubit arrays an appealing solid-state platform to realize quantum processors. The dynamic and long-range connectivity enabled by shuttling is also essential for many quantum error-correction (QEC) schemes. Here, we demonstrate a silicon spin-qubit device that comprises a shuttling bus for coherently transporting qubits that can interact at four isolated locations we call bus stops. We dynamically populate the array and tune all single- and two-qubit operations using shuttling and quantum non-demolition (QND) spin measurements, without access to charge sensing in most of the device. We achieve universal control of the effective five-qubit processor and select the connectivity required to form a surface-code stabilizer plaquette that supports X- and Z-type parity checks up to weight-four. We use the parity checks to generate multi-qubit entanglement between all qubit combinations in the array and report the genuine entanglement of a five-qubit Greenberger-Horne-Zeilinger (GHZ) state, constituting the largest such state ever constructed with gate-defined semiconductor spins. This work opens immediate opportunities to pursue QEC experiments with spin qubits, and the protocols developed here lay the groundwork for the modular calibration and operation of sparse spin qubit arrays.

cond-mat.mes-hallCross-listedarXiv:2601.23267•Nature•Feb 2, 2026•25 citations

Multi-qubit parity measurement in circuit quantum electrodynamics

David Peter Divincenzo, Firat Solgun

We present a concept for performing direct parity measurements on three or more qubits in microwave structures with superconducting resonators coupled to Josephson-junction qubits. We write the quantum-eraser conditions that must be fulfilled for the parity measurements as requirements for the scattering phase shift of our microwave structure. We show that these conditions can be fulfilled with present-day devices. We present one particular scheme, implemented with two-dimensional cavity techniques, in which each qubit should be coupled equally to two different microwave cavities. The magnitudes of the couplings that are needed are in the range that has been achieved in current experiments. A quantum calculation indicates that the measurement is optimal if the scattering signal can be measured with near single-photon sensitivity. A comparison with an extension of a related proposal from cavity optics is presented. We present a second scheme, for which a scalable implementation of the four-qubit parities of the surface quantum error correction code can be envisioned. It uses three-dimensional cavity structures, using cavity symmetries to achieve the necessary multiple resonant modes within a single resonant structure.

arXiv:1205.1910•New Journal of Physics•Jul 2, 2013•46 citations

Quantum Error Detection in Qubit-Resonator Star Architecture

Florian Vigneau, Sourav Majumder, Aniket Rath +13 more

Achieving industrial quantum advantage is unlikely without the use of quantum error correction (QEC). Other QEC codes beyond surface code are being experimentally studied, such as color codes and quantum low-density parity check codes, that could benefit from new quantum processing unit (QPU) architectures. We introduce the six-qubit star lattice architecture that offers parallelism and effective local all-to-all connectivity and thus enables hardware-efficient implementation of certain QEC codes. As a first demonstration of this new architecture, we encode two logical qubits in a six-qubit superconducting QPU with a star topology using the ⟦ 4 , 2 , 2 ⟧ code and characterize the logical states with the classical shadow framework. Logical lifetime and logical error rate are measured over repeated quantum error detection cycles for various logical states including a logical Bell state. We measure logical state fidelities above 96% for every cardinal logical state, find logical lifetimes above the best physical element, and logical error-per-cycle values ranging from 0.25(2)% to 0.91(3)%. In future, such star units can be tiled into a lattice to enable QEC codes with high-weight and overlapping stabilizers for improved encoding rates.

arXiv:2503.12869•PRX Quantum•Nov 12, 2025•11 citations
We present parity measurements on a five-qubit lattice with connectivity amenable to the surface code quantum error correction architecture. Using all-microwave controls of superconducting qubits coupled via resonators, we encode the parities of four data qubit states in either the X or the Z basis. Given the connectivity of the lattice, we perform a full characterization of the static Z interactions within the set of five qubits, as well as dynamical Z interactions brought along by single- and two-qubit microwave drives. The parity measurements are significantly improved by modifying the microwave two-qubit gates to dynamically remove nonideal Z errors.
Quantum error correction will be a necessary component towards realizing scalable quantum computers with physical qubits. Theoretically, it is possible to perform arbitrarily long computations if the error rate is below a threshold value. The two-dimensional surface code permits relatively high fault-tolerant thresholds at the ~1% level, and only requires a latticed network of qubits with nearest-neighbor interactions. Superconducting qubits have continued to steadily improve in coherence, gate, and readout fidelities, to become a leading candidate for implementation into larger quantum networks. Here we describe characterization experiments and calibration of a system of four superconducting qubits arranged in a planar lattice, amenable to the surface code. Insights into the particular qubit design and comparison between simulated parameters and experimentally determined parameters are given. Single- and two-qubit gate tune-up procedures are described and results for simultaneously benchmarking pairs of two-qubit gates are given. All controls are eventually used for an arbitrary error detection protocol described in separate work [Corcoles et al., Nature Communications, 6, 2015].
The ability to detect and deal with errors when manipulating quantum systems is a fundamental requirement for fault-tolerant quantum computing. Unlike classical bits that are subject to only digital bit-flip errors, quantum bits are susceptible to a much larger spectrum of errors, for which any complete quantum error-correcting code must account. Whilst classical bit-flip detection can be realized via a linear array of qubits, a general fault-tolerant quantum error-correcting code requires extending into a higher-dimensional lattice. Here we present a quantum error detection protocol on a two-by-two planar lattice of superconducting qubits. The protocol detects an arbitrary quantum error on an encoded two-qubit entangled state via quantum non-demolition parity measurements on another pair of error syndrome qubits. This result represents a building block towards larger lattices amenable to fault-tolerant quantum error correction architectures such as the surface code.
A remarkable characteristic of quantum computing is the potential for reliable computation despite faulty qubits. This can be achieved through quantum error correction, which is typically implemented by repeatedly applying static syndrome checks, permitting correction of logical information. Recently, the development of time-dynamic approaches to error correction has enabled different codes and implementations that do not rely on static syndrome measurements. Here we experimentally demonstrate three time-dynamic implementations of the surface code, each offering a distinct solution to hardware design challenges faced by surface code realizations. First, we embed the surface code on a hexagonal lattice, reducing the necessary couplings per qubit from four to three. Second, we walk a surface code, swapping the role of data and measure qubits each round, achieving error correction with built-in removal of accumulated non-computational errors. Finally, we realize the surface code using iSWAP gates instead of the traditional CNOT, extending the set of viable gates for error correction without additional overhead. We measure the error suppression factor when scaling from distance-3 to distance-5 codes of Λ35,hex = 2.15(2), Λ35,walk = 1.69(6) and Λ35,iSWAP = 1.56(2), achieving state-of-the-art error suppression for each. Our work demonstrates that dynamic circuit approaches meet the demands for fault tolerance and enable alternative strategies for scalable hardware design. Typical quantum error correcting codes assign fixed roles to the underlying physical qubits. Now the performance benefits of alternative, dynamic error correction schemes have been demonstrated on a superconducting quantum processor.
Recent advances in coherent spin shuttling have made sparse semiconductor spin qubit arrays an appealing solid-state platform to realize quantum processors. The dynamic and long-range connectivity enabled by shuttling is also essential for many quantum error-correction (QEC) schemes. Here, we demonstrate a silicon spin-qubit device that comprises a shuttling bus for coherently transporting qubits that can interact at four isolated locations we call bus stops. We dynamically populate the array and tune all single- and two-qubit operations using shuttling and quantum non-demolition (QND) spin measurements, without access to charge sensing in most of the device. We achieve universal control of the effective five-qubit processor and select the connectivity required to form a surface-code stabilizer plaquette that supports X- and Z-type parity checks up to weight-four. We use the parity checks to generate multi-qubit entanglement between all qubit combinations in the array and report the genuine entanglement of a five-qubit Greenberger-Horne-Zeilinger (GHZ) state, constituting the largest such state ever constructed with gate-defined semiconductor spins. This work opens immediate opportunities to pursue QEC experiments with spin qubits, and the protocols developed here lay the groundwork for the modular calibration and operation of sparse spin qubit arrays.
We present a concept for performing direct parity measurements on three or more qubits in microwave structures with superconducting resonators coupled to Josephson-junction qubits. We write the quantum-eraser conditions that must be fulfilled for the parity measurements as requirements for the scattering phase shift of our microwave structure. We show that these conditions can be fulfilled with present-day devices. We present one particular scheme, implemented with two-dimensional cavity techniques, in which each qubit should be coupled equally to two different microwave cavities. The magnitudes of the couplings that are needed are in the range that has been achieved in current experiments. A quantum calculation indicates that the measurement is optimal if the scattering signal can be measured with near single-photon sensitivity. A comparison with an extension of a related proposal from cavity optics is presented. We present a second scheme, for which a scalable implementation of the four-qubit parities of the surface quantum error correction code can be envisioned. It uses three-dimensional cavity structures, using cavity symmetries to achieve the necessary multiple resonant modes within a single resonant structure.
Achieving industrial quantum advantage is unlikely without the use of quantum error correction (QEC). Other QEC codes beyond surface code are being experimentally studied, such as color codes and quantum low-density parity check codes, that could benefit from new quantum processing unit (QPU) architectures. We introduce the six-qubit star lattice architecture that offers parallelism and effective local all-to-all connectivity and thus enables hardware-efficient implementation of certain QEC codes. As a first demonstration of this new architecture, we encode two logical qubits in a six-qubit superconducting QPU with a star topology using the ⟦ 4 , 2 , 2 ⟧ code and characterize the logical states with the classical shadow framework. Logical lifetime and logical error rate are measured over repeated quantum error detection cycles for various logical states including a logical Bell state. We measure logical state fidelities above 96% for every cardinal logical state, find logical lifetimes above the best physical element, and logical error-per-cycle values ranging from 0.25(2)% to 0.91(3)%. In future, such star units can be tiled into a lattice to enable QEC codes with high-weight and overlapping stabilizers for improved encoding rates.