Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1604.05340 · Microwave and Optical Technology Letters

Chromatic effects in beam wander correction for free-space quantum communications

Alberto Carrasco‐Casado, Natalia Denisenko, Verónica Fernández

Published Mar 28, 2016• 6 citations
arXivHTMLPDF

Abstract

Beam wander caused by atmospheric turbulence can significantly degrade the performance of horizontal free-space quantum communication links. Classical beam wander correction techniques cannot be applied due to the stronger requirements of transmitting single photons. One strategy to overcome this limitation consists in using a separate wavelength from that of the quantum signal to analyze the beam wander and use this information for its correction. For this strategy to work adequately, both wavelengths should be affected equally by atmospheric turbulence, i.e. no chromatic effects should be originated from beam wander. In this letter, a series of experiments are performed to prove that this is the case for λ ∼ 850 nm as the quantum signal and λ ∼ 1550 nm as the tracking signal of a quantum communication system. © 2016 Wiley Periodicals, Inc. Microwave Opt Technol Lett 58:1362–1365, 2016

DOI
10.1002/mop.29802

Related papers

Highly-enhanced active beam-wander-correction for free-space quantum communications

Dohoon Lim, Dongkyu Kim, Kyungdeuk Park +2 more

In practical applications to free-space quantum communications, the utilization of active beam coupling and stabilization techniques offers notable advantages, particularly when dealing with limited detecting areas or coupling into single-mode fibers(SMFs) to mitigate background noise. In this work, we introduce highly-enhanced active beam-wander-correction technique, specifically tailored to efficiently couple and stabilize beams into SMFs, particularly in scenarios where initial optical alignment with the SMF is misaligned. To achieve this objective, we implement a SMF auto-coupling algorithm and a decoupled stabilization method, effectively and reliably correcting beam wander caused by atmospheric turbulence effects. The performance of the proposed technique is thoroughly validated through quantitative measurements of the temporal variation in coupling efficiency(coincidence counts) of a laser beam(entangled photons). The results show significant improvements in both mean values and standard deviations of the coupling efficiency, even in the presence of 2.6 km atmospheric turbulence effects. When utilizing a laser source, the coupling efficiency demonstrates a remarkable mean value increase of over 50 %, accompanied by a substantial 4.4-fold improvement in the standard deviation. For the entangled photon source, a fine mean value increase of 14 % and an approximate 2-fold improvement in the standard deviation are observed. Furthermore,the proposed technique successfully restores the fidelity of the polarization-entangled state, which has been compromised by atmospheric effects in the free-space channel, to a level close to the fidelity measured directly from the source. Our work will be helpful in designing spatial light-fiber coupling system not only for free-space quantum communications but also for high-speed laser communications.

arXiv:2310.17900•Optics Express•Nov 3, 2023•5 citations

Effects of turbulence on a combined 1535-nm retro reflective and a low-intensity single-path 850-nm optical communication link

Fredrik Kullander, Lars J. Sjöqvist, Per Jönsson

Atmospheric turbulence can significantly degrade the performance of free-space optical communication links. Beam wander, intensity scintillations, beam broadening and angle of arrival fluctuations give rise to signal fading with communication channel drop-outs. In this work the performance of the potentially beneficial combination of a retro reflective link operating at 1535 nm in conjunction with a single-photon quantum key distribution link at 850 nm was studied. The general idea is that the weak light beam of the quantum channel can be steered and controlled by the 1535 nm signal. A dual-channel laser unit, with output beams at 850 and 1535 nm, was used to characterise turbulence effects along an atmospheric path close above ground. The laser beams were retro reflected from a corner cube and detected in the same laser unit. The 1535 nm beam was monitored with a position sensitive detector while the 850 nm beam (low intensity channel) was aligned with the 1535 nm beam and detected separately but along the same optical axis of the laser unit. Effects of beam wander, angular fluctuations and intensity scintillations were studied experimentally at different turbulence strengths and weather conditions. The experimental results are discussed with respect to theoretical models.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Sep 28, 2006•8 citations

Theory of atmospheric quantum channels based on the law of total probability

Dmytro Vasylyev, W. Vogel, А. А. Семенов

The atmospheric turbulence is the main factor that influences quantum properties of propagating optical signals and may sufficiently degrade the performance of quantum communication protocols. The probability distribution of transmittance (PDT) for free-space channels is the main characteristic of the atmospheric links. Applying the law of total probability, we derive the PDT by separating the contributions from turbulence-induced beam wandering and beam-spot distortions. As a result, the obtained PDT varies from log-negative Weibull to truncated log-normal distributions depending on the channel characteristics. Moreover, we show that the method allows one to consistently describe beam tracking, a procedure which is typically used in practical long-distance free-space quantum communication. We analyze the security of decoy-state quantum key exchange through the turbulent atmosphere and show that beam tracking does not always improve quantum communication.

arXiv:1804.00172•Physical Review A•Jun 26, 2018•52 citations

Characterization of free-space quantum channels

Dmytro Vasylyev, Andrii Semenov, Werner Vogel

Many fundamental and applied experiments in quantum optics require transferring nonclassical states of light through large distances. In this context the free-space channels are a very promising alternative to optical fibers as they are mobile and enable to establish communications with moving objects, using satellites for global quantum links. For such channels the atmospheric turbulence is the main disturbing factor. The statistical properties of the fluctuating transmittance through the turbulent atmosphere are given by the probability distribution of transmittance (PDT). We derive the consistent PDTs for the atmospheric quantum channels by step-by-step inclusion of various atmospheric effects such as beam wandering, beam broadening and deformation of the beam into elliptic form, beam deformations into arbitrary forms. We discuss the applicability of PDT models for different propagation distances and optical turbulence strengths in the case when the receiver module has an annular aperture. We analyze the optimal detection and correction strategies which can improve the channel transmission characteristics. The obtained results are important for the design of optical experiments including postselection and adaptive strategies and for the security analysis of quantum communication protocols in freespace.

arXiv:1810.05700•Quantum Communications and Quantum Imaging•Sep 18, 2018•13 citations

Enabling daylight free-space quantum communication through beam stabilization techniques

Jorge Gómez-García, Alejandro Ocampos-Guillén, Natalia Denisenko +1 more

Daylight performance of open-air quantum communications is hindered by background light coupling into single-photon detectors. Since most detectors tend to have small active areas (20-200 microns) beam deviations caused by atmospheric turbulence induce losses in the quantum signal. Therefore, the receiver’s field of view needs to be left sufficiently large to avoid these losses, which in turn increases the background noise in the system and thus the quantum bit error rate contribution caused by background noise (QBERbackg). Active compensation techniques stabilize the beam in a pre-aligned position, allowing a reduction of the field of view. These techniques use fast steering mirrors (FSMs) and position sensitive detectors (PSDs) in a feedback loop to compensate for these deviations and maintain the quantum signal aligned within the receiver field of view even in the presence of fast turbulence (up to 200 Hz). Using a single FSM correcting system stabilizes the beam in the receiver in a single plane, whereas a double FSM system (see Fig. 1) corrects all beam deviations throughout the whole optical axis. A double correcting system was tested in a free-space 30-metre link and beam deviations were reduced an average factor of 3 (in diameter) and a maximum factor of 5 (see Fig. 2), which corresponds to a decrease in area of 89% and 96.4%, respectively, meaning that background noise is reduced in the same amount. The Fourier transform of the deviations were characterized to evaluate the dependence of the correction with the frequency components of the turbulence, establishing that a good correction was achieved up to 200-250 Hz (see Fig. 3), which corresponds to the bandwidth of beam wander. Frequencies beyond this range correspond to higher degree waveform distortions (like scintillation) which necessitate from other correcting techniques and cannot be corrected with tip-and-tilt compensation, which is our case. The performance of this compensation system was simulated with ray-tracing software up to a distance of 500 metres in very high turbulent regime (Cn2=10-11 m-2/3) confirming a ~90% reduction in QBERbackg is still present.

•Jul 10, 2017•0 citations

Comparison of beam wander correction by quadrant and ideal detectors for aerial quantum communication links

Jorge Gómez-García

We report an analysis of beam wander correction by both a quadrant and an ideal detector in a close loop configuration. The analysis is performed with the aim of finding the optimum detector for beam tracking of free space quantum communication links. The effect of beam wander will be modelled as an angle-of-arrival fluctuation at the receiver. A simulation using ray tracing software was performed to simulate the correction for different values of the angle of arrival, ranging from those typical from atmospheric turbulent regimes, with values of a few mili °, to larger values up to 1° from larger possible misalignments from the system. The simulating correcting system indicates that a quadrant detector is only successful for large values of the angle of arrival(> 0.2°),whereas for a smaller range no correction is shown due to the limiting factor imposed by aberrations of the focusing lens. We also show that the optimum spot diameter depends on the angle of arrival: if this is smaller than 0.5⁰, a spot diameter of at least Dspot/Dgap=2.5 should be used, whereas for larger values of the angle of arrival, a spot diameter of at least Dspot/Dgap=3.5 is required.

•Oct 15, 2015•1 citation
Beam wander caused by atmospheric turbulence can significantly degrade the performance of horizontal free-space quantum communication links. Classical beam wander correction techniques cannot be applied due to the stronger requirements of transmitting single photons. One strategy to overcome this limitation consists in using a separate wavelength from that of the quantum signal to analyze the beam wander and use this information for its correction. For this strategy to work adequately, both wavelengths should be affected equally by atmospheric turbulence, i.e. no chromatic effects should be originated from beam wander. In this letter, a series of experiments are performed to prove that this is the case for λ ∼ 850 nm as the quantum signal and λ ∼ 1550 nm as the tracking signal of a quantum communication system. © 2016 Wiley Periodicals, Inc. Microwave Opt Technol Lett 58:1362–1365, 2016
In practical applications to free-space quantum communications, the utilization of active beam coupling and stabilization techniques offers notable advantages, particularly when dealing with limited detecting areas or coupling into single-mode fibers(SMFs) to mitigate background noise. In this work, we introduce highly-enhanced active beam-wander-correction technique, specifically tailored to efficiently couple and stabilize beams into SMFs, particularly in scenarios where initial optical alignment with the SMF is misaligned. To achieve this objective, we implement a SMF auto-coupling algorithm and a decoupled stabilization method, effectively and reliably correcting beam wander caused by atmospheric turbulence effects. The performance of the proposed technique is thoroughly validated through quantitative measurements of the temporal variation in coupling efficiency(coincidence counts) of a laser beam(entangled photons). The results show significant improvements in both mean values and standard deviations of the coupling efficiency, even in the presence of 2.6 km atmospheric turbulence effects. When utilizing a laser source, the coupling efficiency demonstrates a remarkable mean value increase of over 50 %, accompanied by a substantial 4.4-fold improvement in the standard deviation. For the entangled photon source, a fine mean value increase of 14 % and an approximate 2-fold improvement in the standard deviation are observed. Furthermore,the proposed technique successfully restores the fidelity of the polarization-entangled state, which has been compromised by atmospheric effects in the free-space channel, to a level close to the fidelity measured directly from the source. Our work will be helpful in designing spatial light-fiber coupling system not only for free-space quantum communications but also for high-speed laser communications.
Atmospheric turbulence can significantly degrade the performance of free-space optical communication links. Beam wander, intensity scintillations, beam broadening and angle of arrival fluctuations give rise to signal fading with communication channel drop-outs. In this work the performance of the potentially beneficial combination of a retro reflective link operating at 1535 nm in conjunction with a single-photon quantum key distribution link at 850 nm was studied. The general idea is that the weak light beam of the quantum channel can be steered and controlled by the 1535 nm signal. A dual-channel laser unit, with output beams at 850 and 1535 nm, was used to characterise turbulence effects along an atmospheric path close above ground. The laser beams were retro reflected from a corner cube and detected in the same laser unit. The 1535 nm beam was monitored with a position sensitive detector while the 850 nm beam (low intensity channel) was aligned with the 1535 nm beam and detected separately but along the same optical axis of the laser unit. Effects of beam wander, angular fluctuations and intensity scintillations were studied experimentally at different turbulence strengths and weather conditions. The experimental results are discussed with respect to theoretical models.
The atmospheric turbulence is the main factor that influences quantum properties of propagating optical signals and may sufficiently degrade the performance of quantum communication protocols. The probability distribution of transmittance (PDT) for free-space channels is the main characteristic of the atmospheric links. Applying the law of total probability, we derive the PDT by separating the contributions from turbulence-induced beam wandering and beam-spot distortions. As a result, the obtained PDT varies from log-negative Weibull to truncated log-normal distributions depending on the channel characteristics. Moreover, we show that the method allows one to consistently describe beam tracking, a procedure which is typically used in practical long-distance free-space quantum communication. We analyze the security of decoy-state quantum key exchange through the turbulent atmosphere and show that beam tracking does not always improve quantum communication.
Many fundamental and applied experiments in quantum optics require transferring nonclassical states of light through large distances. In this context the free-space channels are a very promising alternative to optical fibers as they are mobile and enable to establish communications with moving objects, using satellites for global quantum links. For such channels the atmospheric turbulence is the main disturbing factor. The statistical properties of the fluctuating transmittance through the turbulent atmosphere are given by the probability distribution of transmittance (PDT). We derive the consistent PDTs for the atmospheric quantum channels by step-by-step inclusion of various atmospheric effects such as beam wandering, beam broadening and deformation of the beam into elliptic form, beam deformations into arbitrary forms. We discuss the applicability of PDT models for different propagation distances and optical turbulence strengths in the case when the receiver module has an annular aperture. We analyze the optimal detection and correction strategies which can improve the channel transmission characteristics. The obtained results are important for the design of optical experiments including postselection and adaptive strategies and for the security analysis of quantum communication protocols in freespace.
Daylight performance of open-air quantum communications is hindered by background light coupling into single-photon detectors. Since most detectors tend to have small active areas (20-200 microns) beam deviations caused by atmospheric turbulence induce losses in the quantum signal. Therefore, the receiver’s field of view needs to be left sufficiently large to avoid these losses, which in turn increases the background noise in the system and thus the quantum bit error rate contribution caused by background noise (QBERbackg). Active compensation techniques stabilize the beam in a pre-aligned position, allowing a reduction of the field of view. These techniques use fast steering mirrors (FSMs) and position sensitive detectors (PSDs) in a feedback loop to compensate for these deviations and maintain the quantum signal aligned within the receiver field of view even in the presence of fast turbulence (up to 200 Hz). Using a single FSM correcting system stabilizes the beam in the receiver in a single plane, whereas a double FSM system (see Fig. 1) corrects all beam deviations throughout the whole optical axis. A double correcting system was tested in a free-space 30-metre link and beam deviations were reduced an average factor of 3 (in diameter) and a maximum factor of 5 (see Fig. 2), which corresponds to a decrease in area of 89% and 96.4%, respectively, meaning that background noise is reduced in the same amount. The Fourier transform of the deviations were characterized to evaluate the dependence of the correction with the frequency components of the turbulence, establishing that a good correction was achieved up to 200-250 Hz (see Fig. 3), which corresponds to the bandwidth of beam wander. Frequencies beyond this range correspond to higher degree waveform distortions (like scintillation) which necessitate from other correcting techniques and cannot be corrected with tip-and-tilt compensation, which is our case. The performance of this compensation system was simulated with ray-tracing software up to a distance of 500 metres in very high turbulent regime (Cn2=10-11 m-2/3) confirming a ~90% reduction in QBERbackg is still present.
We report an analysis of beam wander correction by both a quadrant and an ideal detector in a close loop configuration. The analysis is performed with the aim of finding the optimum detector for beam tracking of free space quantum communication links. The effect of beam wander will be modelled as an angle-of-arrival fluctuation at the receiver. A simulation using ray tracing software was performed to simulate the correction for different values of the angle of arrival, ranging from those typical from atmospheric turbulent regimes, with values of a few mili °, to larger values up to 1° from larger possible misalignments from the system. The simulating correcting system indicates that a quadrant detector is only successful for large values of the angle of arrival(> 0.2°),whereas for a smaller range no correction is shown due to the limiting factor imposed by aberrations of the focusing lens. We also show that the optimum spot diameter depends on the angle of arrival: if this is smaller than 0.5⁰, a spot diameter of at least Dspot/Dgap=2.5 should be used, whereas for larger values of the angle of arrival, a spot diameter of at least Dspot/Dgap=3.5 is required.