Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1412.8015 · Review of Scientific Instruments

Introduction of DC line structures into a superconducting microwave 3D cavity

Wei-Cheng Kong, Guang-Wei Deng, Shu-Xiao Li, Hai-Ou Li, Gang Cao, Ming Xiao, Guo-Ping Guo

Published Feb 1, 2015• 11 citations
arXivHTMLPDF

Abstract

We report a technique that can noninvasively add multiple DC wires into a 3D superconducting microwave cavity for electronic devices that require DC electrical terminals. We studied the influence of our DC lines on the cavity performance systematically. We found that the quality factor of the cavity is reduced if any of the components of the electrical wires cross the cavity equipotential planes. Using this technique, we were able to incorporate a quantum dot (QD) device into a 3D cavity. We then controlled and measured the QD transport signal using the DC lines. We have also studied the heating effects of the QD by the microwave photons in the cavity.

DOI
10.1063/1.4913252

Related papers

Introduction of a dc bias into a high-Q superconducting microwave cavity

Fei Chen, A. J. Sirois, Raymond W. Simmonds +1 more

We report a technique for applying a dc voltage or current bias to the center conductor of a high-quality factor superconducting microwave cavity without significantly disturbing selected cavity modes. This is accomplished by incorporating dc bias lines into the cavity at specific locations. The measured S-matrix parameters of the system are in good agreement with theoretical predictions and simulations. We find that at 4 K the quality factor of the cavity degrades by less than 1% under the application of a dc bias.

arXiv:1101.4218•Applied Physics Letters•Mar 28, 2011•45 citations

Applying electric and magnetic field bias in a 3D superconducting waveguide cavity with high quality factor

M. Stammeier, Sébastien Garcia, Andreas J. Wallraff

Abstract Three-dimensional microwave waveguide cavities are essential tools for many cavity quantum electrodynamics experiments. However, the need to control quantum emitters with dc magnetic fields inside the cavity often limits such experiments to normal-conducting cavities with relatively low quality factors of about 10 4 . Similarly, controlling quantum emitters with dc electric fields in normal- and superconducting waveguide cavities has so far been difficult, because the insertion of dc electrodes has strongly limited the quality factor. Here, we present a method to apply dc electric fields within a superconducting waveguide cavity, which is based on the insertion of dc electrodes at the nodes of the microwave electric field. Moreover, we present a method to apply dc magnetic fields within the same cavity by trapping the magnetic flux in holes positioned in facing walls of the cavity. We demonstrate that the TE 301 mode of such a superconducting, rectangular cavity made from niobium maintains a high internal quality factor of Q int ≃ 1.7 × 10 6 at the few photon level and a base temperature of 3 K. A cloud of Rydberg atoms coupled to the microwave electric field of the cavity is used to probe the applied dc electric and magnetic fields via the quadratic Stark effect and the Zeeman effect, respectively.

arXiv:1712.08631•Quantum Science and Technology•Jul 13, 2018•19 citations

Microwave engineering for semiconductor quantum dots in a cQED architecture

Nathan Holman, J. P. Dodson, L. F. Edge +4 more

We develop an engineered microwave environment for coupling high Q superconducting resonators to quantum dots using a multilayer fabrication stack for dot control wiring. Analytical and numerical models are presented, which show that high resonator quality factors can be attained by either minimizing the parasitic coupling capacitance to the leads or creating a low effective environmental impedance at the cavity frequency. We implement the later approach by fabricating low characteristic impedance (Zg≈10 Ω) microstrips on-chip for the dot bias wiring and show resonator quality factors of 8140 that can be attained without the addition of explicit filtering. Using this approach, we demonstrate single electron occupation in double and triple dots detected via dipole or quadrupole coupling to a superconducting resonator. Additionally, by using multilayer fabrication, we are able to improve ground plane integrity and keep microwave crosstalk below −20 dB out to 18 GHz while maintaining high wire density, which will be necessary for future circuit quantum electrodynamics quantum dot processors.

arXiv:2006.02514•Applied Physics Letters•Aug 24, 2020•17 citations

A split-cavity design for the incorporation of a DC bias in a 3D microwave cavity

Martijn A. Cohen, Mingyun Yuan, Bas W. A. de Jong +3 more

We report on a technique for applying a DC bias in a 3D microwave cavity. We achieve this by isolating the two halves of the cavity with a dielectric and directly using them as DC electrodes. As a proof of concept, we embed a variable capacitance diode in the cavity and tune the resonant frequency with a DC voltage, demonstrating the incorporation of a DC bias into the 3D cavity with no measurable change in its quality factor at room temperature. We also characterize the architecture at millikelvin temperatures and show that the split cavity design maintains a quality factor Qi ∼ 8.8 × 105, making it promising for future quantum applications.

arXiv:1704.07220•Applied Physics Letters•Apr 24, 2017•11 citations

Gate-compatible circuit quantum electrodynamics in a three-dimensional cavity architecture

Zezhou Xia, Jierong Huo, Zonglin Li +14 more

Semiconductor-based superconducting qubits offer a versatile platform for studying hybrid quantum devices in circuit quantum electrodynamics (QED) architecture. Most of these circuit QED experiments utilize coplanar waveguides, where the incorporation of dc gate lines is straightforward. Here, we present a technique for probing gate-tunable hybrid devices using a three-dimensional (3D) microwave cavity. A recess is machined inside the cavity wall for the placement of devices and gate lines. We validate this design using a hybrid device based on an InAs-Al nanowire Josephson junction. The coupling between the device and the cavity is facilitated by a long superconducting strip, the antenna. The Josephson junction and the antenna together form a gatemon qubit. We further demonstrate the gate-tunable cavity shift and two-tone qubit spectroscopy. This technique could be used to probe various quantum devices and materials in a 3D circuit QED architecture that requires dc gate voltages.

arXiv:2311.07337•Physical Review Applied•Mar 18, 2024•8 citations

Demonstration of superconducting micromachined cavities

T. Brecht, Matthew J. Reagor, Yiwen Chu +5 more

Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics. Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting seams potentially dissipate crossing currents and limit performance. In this letter, we present measured quality factors of superconducting cavity resonators of several materials, dimensions, and seam locations. We observe that superconducting indium can be a low-loss RF conductor and form low-loss seams. Leveraging this, we create a superconducting micromachined resonator with indium that has a quality factor of two million, despite a greatly reduced mode volume. Inter-layer coupling to this type of resonator is achieved by an aperture located under a planar transmission line. The described techniques demonstrate a proof-of-principle for multilayer microwave integrated quantum circuits for scalable quantum computing.

arXiv:1509.01119•Applied Physics Letters•Nov 9, 2015•88 citations
We report a technique that can noninvasively add multiple DC wires into a 3D superconducting microwave cavity for electronic devices that require DC electrical terminals. We studied the influence of our DC lines on the cavity performance systematically. We found that the quality factor of the cavity is reduced if any of the components of the electrical wires cross the cavity equipotential planes. Using this technique, we were able to incorporate a quantum dot (QD) device into a 3D cavity. We then controlled and measured the QD transport signal using the DC lines. We have also studied the heating effects of the QD by the microwave photons in the cavity.
We report a technique for applying a dc voltage or current bias to the center conductor of a high-quality factor superconducting microwave cavity without significantly disturbing selected cavity modes. This is accomplished by incorporating dc bias lines into the cavity at specific locations. The measured S-matrix parameters of the system are in good agreement with theoretical predictions and simulations. We find that at 4 K the quality factor of the cavity degrades by less than 1% under the application of a dc bias.
Abstract Three-dimensional microwave waveguide cavities are essential tools for many cavity quantum electrodynamics experiments. However, the need to control quantum emitters with dc magnetic fields inside the cavity often limits such experiments to normal-conducting cavities with relatively low quality factors of about 10 4 . Similarly, controlling quantum emitters with dc electric fields in normal- and superconducting waveguide cavities has so far been difficult, because the insertion of dc electrodes has strongly limited the quality factor. Here, we present a method to apply dc electric fields within a superconducting waveguide cavity, which is based on the insertion of dc electrodes at the nodes of the microwave electric field. Moreover, we present a method to apply dc magnetic fields within the same cavity by trapping the magnetic flux in holes positioned in facing walls of the cavity. We demonstrate that the TE 301 mode of such a superconducting, rectangular cavity made from niobium maintains a high internal quality factor of Q int ≃ 1.7 × 10 6 at the few photon level and a base temperature of 3 K. A cloud of Rydberg atoms coupled to the microwave electric field of the cavity is used to probe the applied dc electric and magnetic fields via the quadratic Stark effect and the Zeeman effect, respectively.
We develop an engineered microwave environment for coupling high Q superconducting resonators to quantum dots using a multilayer fabrication stack for dot control wiring. Analytical and numerical models are presented, which show that high resonator quality factors can be attained by either minimizing the parasitic coupling capacitance to the leads or creating a low effective environmental impedance at the cavity frequency. We implement the later approach by fabricating low characteristic impedance (Zg≈10 Ω) microstrips on-chip for the dot bias wiring and show resonator quality factors of 8140 that can be attained without the addition of explicit filtering. Using this approach, we demonstrate single electron occupation in double and triple dots detected via dipole or quadrupole coupling to a superconducting resonator. Additionally, by using multilayer fabrication, we are able to improve ground plane integrity and keep microwave crosstalk below −20 dB out to 18 GHz while maintaining high wire density, which will be necessary for future circuit quantum electrodynamics quantum dot processors.
We report on a technique for applying a DC bias in a 3D microwave cavity. We achieve this by isolating the two halves of the cavity with a dielectric and directly using them as DC electrodes. As a proof of concept, we embed a variable capacitance diode in the cavity and tune the resonant frequency with a DC voltage, demonstrating the incorporation of a DC bias into the 3D cavity with no measurable change in its quality factor at room temperature. We also characterize the architecture at millikelvin temperatures and show that the split cavity design maintains a quality factor Qi ∼ 8.8 × 105, making it promising for future quantum applications.
Semiconductor-based superconducting qubits offer a versatile platform for studying hybrid quantum devices in circuit quantum electrodynamics (QED) architecture. Most of these circuit QED experiments utilize coplanar waveguides, where the incorporation of dc gate lines is straightforward. Here, we present a technique for probing gate-tunable hybrid devices using a three-dimensional (3D) microwave cavity. A recess is machined inside the cavity wall for the placement of devices and gate lines. We validate this design using a hybrid device based on an InAs-Al nanowire Josephson junction. The coupling between the device and the cavity is facilitated by a long superconducting strip, the antenna. The Josephson junction and the antenna together form a gatemon qubit. We further demonstrate the gate-tunable cavity shift and two-tone qubit spectroscopy. This technique could be used to probe various quantum devices and materials in a 3D circuit QED architecture that requires dc gate voltages.
Superconducting enclosures will be key components of scalable quantum computing devices based on circuit quantum electrodynamics. Within a densely integrated device, they can protect qubits from noise and serve as quantum memory units. Whether constructed by machining bulk pieces of metal or microfabricating wafers, 3D enclosures are typically assembled from two or more parts. The resulting seams potentially dissipate crossing currents and limit performance. In this letter, we present measured quality factors of superconducting cavity resonators of several materials, dimensions, and seam locations. We observe that superconducting indium can be a low-loss RF conductor and form low-loss seams. Leveraging this, we create a superconducting micromachined resonator with indium that has a quality factor of two million, despite a greatly reduced mode volume. Inter-layer coupling to this type of resonator is achieved by an aperture located under a planar transmission line. The described techniques demonstrate a proof-of-principle for multilayer microwave integrated quantum circuits for scalable quantum computing.