Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Log inSign up
Challenges
Datasets
Workspaces
Papers
Discussions
Leaderboard
Blog
Job Board
Q3AS

© 2026 Aqora Quantum S.A.S.

TermsPrivacyLegal Notice

arXiv:1406.2936 · Applied Physics Letters

Millimeter wave detection via Autler-Townes splitting in rubidium Rydberg atoms

Joshua A. Gordon, Christopher L. Holloway, Andrew Schwarzkopf, Dave A. Anderson, Stephanie Miller, Nithiwadee Thaicharoen, Georg A. Raithel

Published Jul 14, 2014• 211 citations
arXivHTMLPDF

Abstract

In this paper, we demonstrate the detection of millimeter waves via Autler-Townes splitting in 85Rb Rydberg atoms. This method may provide an independent, atom-based, SI-traceable method for measuring mm-wave electric fields, which addresses a gap in current calibration techniques in the mm-wave regime. The electric-field amplitude within a rubidium vapor cell in the WR-10 wave guide band is measured for frequencies of 93.71 GHz and 104.77 GHz. Relevant aspects of Autler-Townes splitting originating from a four-level electromagnetically induced transparency scheme are discussed. We measured the E-field generated by an open-ended waveguide using this technique. Experimental results are compared to a full-wave finite element simulation.

DOI
10.1063/1.4890094

Related papers

Atom-based RF electric field metrology above 100 GHz

Matthew T. Simons, Joshua A. Gordon, Christopher L. Holloway

Atom-based radio-frequency (RF) electric field probes have the potential to improve electric field measurements for a broad range of frequencies (from a few GHz to 100s of GHz) and field strengths (mV/m to kV/m). For these probes to become a common measurement method, their range must be extended to high frequency (>100 GHz) and low field strength regimes. We present SI-traceable electric field measurements of RF fields above 100 GHz, using Autler-Townes splitting of Rydberg electromagnetically-induced transparency in a rubidium (Rb) vapor. We also demonstrate several techniques, including RF detuning from resonance and enhanced absorption, for increasing the probe sensitivity.

Proceedings of SPIE, the International Society for Optical Engineering/Proceedings of SPIE•Feb 25, 2016•5 citations

THz electrometry with Rydberg atoms and all IR lasers

Shuying Chen, Dominic J. Reed, Lucy A. Downes +5 more

Rydberg electromagnetically induced transparency (EIT) and Autler-Townes (AT) splitting in an atomic vapor cell can be used as novel methods for electric-magnetic field detection. Here we make use of 3 infrared lasers to realize a Rydberg EIT system in a thermal rubidium vapor cell. With the AT splitting induced by the THz radiation, we observe a linear trend between THz field amplitude and the frequency splitting of the absorption dips and EIT transmission peaks. Due to the well-known atomic transition dipole moment of the Rydberg state, the THz electric field can be calibrated from the frequency splitting, making this Rydberg atomic measurement system a practical tool for THz field detection.

International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz)•Aug 29, 2021•1 citation

Atom-Based RF Electric Field Metrology: From Self-Calibrated Measurements to Subwavelength and Near-Field Imaging

Christopher L. Holloway, Matthew T. Simons, Joshua A. Gordon +4 more

We discuss a fundamentally new method for electric (E) field strength (V/m) metrology applicable to the near-field. This new approach is significantly different from currently used field measurement techniques in that it is based on the interaction of radio-frequency (RF) E-fields with Rydberg atoms (alkali atoms placed in a glass vapor cell that are excited optically to Rydberg states). The applied RF E-field alters the state of the atoms. The Rydberg atoms act like an RF-to-optical transducer, converting an RF E-field strength to an optical-frequency response. In this new approach, we employ the phenomena of electromagnetically induced transparency (EIT) and Autler-Townes splitting. The RF transition in the four-level atomic system causes a split of the EIT transmission spectrum of a probe laser into two peaks. This splitting is easily measured and is directly proportional to the applied RF E-field amplitude. The significant dipole response of Rydberg atoms enables this technique to make self-calibrating measurements over a large frequency band including 500 MHz to 500 GHz (and possibly up to 1 THz and down to 10s of megahertz). In this paper, we report on our results in the development of this metrology approach, including the first fiber-coupled vapor-cell for E-field measurements. We also discuss key applications, including self-calibrated measurements, millimeter-wave and sub-THz measurements, field mapping, and sub-wavelength and near-field imaging. We show results for mapping the fields inside vapor cells, for measuring the E-field distribution along the surface of a circuit board, and for measuring the near-field at the aperture in a cavity. We also discuss the uncertainties of this measurement technique.

IEEE Transactions on Electromagnetic Compatibility•Jan 10, 2017•162 citations

Rydberg Atom-Based Radio Frequency Electrometry: Enhancement of the Self-Calibrated Autler-Townes Sensing Mode

James P. Shaffer, Fabian Ripka, Chang Liu +6 more

We describe experiments relevant to Rydberg atom-based sensing. In Rydberg atom-based sensing, atoms contained in a vapor cell are used as a probe of an incident radio frequency electric field. We present a novel approach based on a collinear three-photon read-out and detection scheme, which extends the sensing range of the self-calibrated Autler-Townes sensing mode to lower electric field strengths. We demonstrate proof of concept and present concrete results from first experiments. We show that we are able to measure electric field strengths below 1 mV/cm in the self-calibrated Autler-Townes regime for a radial dipole moment of 2206 ea0for a transition at 10.7 GHz. We measure an Autler-Townes splitting of 503(6) kHz, which is equivalent to a radio frequency electric field strength of micro-V/cm.

IEEE Conference on Antenna Measurements & Applications•Nov 15, 2021•6 citations

Broadband Rydberg atom-based radio-frequency field sensor

Jiao Yue-Chun, Jianming Zhao, Jia Suo-Tang

Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.

Acta Physica Sinica•Jan 1, 2018•7 citations

Sub-wavelength imaging and field mapping via electromagnetically induced transparency and Autler-Townes splitting in Rydberg atoms

Christopher L. Holloway, Joshua A. Gordon, Andrew Schwarzkopf +4 more

We present a technique for measuring radio-frequency (RF) electric field strengths with sub-wavelength resolution. We use Rydberg states of rubidium atoms to probe the RF field. The RF field causes an energy splitting of the Rydberg states via the Autler-Townes effect, and we detect the splitting via electromagnetically induced transparency (EIT). We use this technique to measure the electric field distribution inside a glass cylinder with applied RF fields at 17.04 GHz and 104.77 GHz. We achieve a spatial resolution of ≈100 μm, limited by the widths of the laser beams utilized for the EIT spectroscopy. We numerically simulate the fields in the glass cylinder and find good agreement with the measured fields. Our results suggest that this technique could be applied to image fields on a small spatial scale over a large range of frequencies, up into the sub-terahertz regime.

arXiv:1404.0289•Applied Physics Letters•Jun 16, 2014•248 citations
In this paper, we demonstrate the detection of millimeter waves via Autler-Townes splitting in 85Rb Rydberg atoms. This method may provide an independent, atom-based, SI-traceable method for measuring mm-wave electric fields, which addresses a gap in current calibration techniques in the mm-wave regime. The electric-field amplitude within a rubidium vapor cell in the WR-10 wave guide band is measured for frequencies of 93.71 GHz and 104.77 GHz. Relevant aspects of Autler-Townes splitting originating from a four-level electromagnetically induced transparency scheme are discussed. We measured the E-field generated by an open-ended waveguide using this technique. Experimental results are compared to a full-wave finite element simulation.
Atom-based radio-frequency (RF) electric field probes have the potential to improve electric field measurements for a broad range of frequencies (from a few GHz to 100s of GHz) and field strengths (mV/m to kV/m). For these probes to become a common measurement method, their range must be extended to high frequency (>100 GHz) and low field strength regimes. We present SI-traceable electric field measurements of RF fields above 100 GHz, using Autler-Townes splitting of Rydberg electromagnetically-induced transparency in a rubidium (Rb) vapor. We also demonstrate several techniques, including RF detuning from resonance and enhanced absorption, for increasing the probe sensitivity.
Rydberg electromagnetically induced transparency (EIT) and Autler-Townes (AT) splitting in an atomic vapor cell can be used as novel methods for electric-magnetic field detection. Here we make use of 3 infrared lasers to realize a Rydberg EIT system in a thermal rubidium vapor cell. With the AT splitting induced by the THz radiation, we observe a linear trend between THz field amplitude and the frequency splitting of the absorption dips and EIT transmission peaks. Due to the well-known atomic transition dipole moment of the Rydberg state, the THz electric field can be calibrated from the frequency splitting, making this Rydberg atomic measurement system a practical tool for THz field detection.
We discuss a fundamentally new method for electric (E) field strength (V/m) metrology applicable to the near-field. This new approach is significantly different from currently used field measurement techniques in that it is based on the interaction of radio-frequency (RF) E-fields with Rydberg atoms (alkali atoms placed in a glass vapor cell that are excited optically to Rydberg states). The applied RF E-field alters the state of the atoms. The Rydberg atoms act like an RF-to-optical transducer, converting an RF E-field strength to an optical-frequency response. In this new approach, we employ the phenomena of electromagnetically induced transparency (EIT) and Autler-Townes splitting. The RF transition in the four-level atomic system causes a split of the EIT transmission spectrum of a probe laser into two peaks. This splitting is easily measured and is directly proportional to the applied RF E-field amplitude. The significant dipole response of Rydberg atoms enables this technique to make self-calibrating measurements over a large frequency band including 500 MHz to 500 GHz (and possibly up to 1 THz and down to 10s of megahertz). In this paper, we report on our results in the development of this metrology approach, including the first fiber-coupled vapor-cell for E-field measurements. We also discuss key applications, including self-calibrated measurements, millimeter-wave and sub-THz measurements, field mapping, and sub-wavelength and near-field imaging. We show results for mapping the fields inside vapor cells, for measuring the E-field distribution along the surface of a circuit board, and for measuring the near-field at the aperture in a cavity. We also discuss the uncertainties of this measurement technique.
We describe experiments relevant to Rydberg atom-based sensing. In Rydberg atom-based sensing, atoms contained in a vapor cell are used as a probe of an incident radio frequency electric field. We present a novel approach based on a collinear three-photon read-out and detection scheme, which extends the sensing range of the self-calibrated Autler-Townes sensing mode to lower electric field strengths. We demonstrate proof of concept and present concrete results from first experiments. We show that we are able to measure electric field strengths below 1 mV/cm in the self-calibrated Autler-Townes regime for a radial dipole moment of 2206 ea0for a transition at 10.7 GHz. We measure an Autler-Townes splitting of 503(6) kHz, which is equivalent to a radio frequency electric field strength of micro-V/cm.
Significant progress has been made in atom-based measurements of length, time, gravity and electromagnetic fields in recently years. Rydberg atom-based microwave electric field measurement, using electromagnetically induced transparency (EIT) in room temperature alkali-metal vapors, has been extensively investigated and aroused the broad interest. This approach may establish a new standard for the measurements of microwave (MW) and radio frequency (RF) electric fields.In this review, we describe the work on a new method of measuring electric fields based on quantum interference by using either cesium or rubidium atoms contained in a dielectric vapor cell. Rydberg atoms with principal quantum number n >>1 have large direct current (DC) polarizabilities and microwave transition dipole moments, thereby making them extremely sensitive to external electric fields. Using the Rydberg three-level EIT to detect the level splitting and shift that is induced by the external field, we can realize a rapid and robust self-calibration method of measuring the electric field in a frequency range from 0.01 GHz to 1000 GHz. For the MW electric field (frequency range > 1 GHz), the MW field causes the Rydberg states to split, known as an Autler-Townes splitting (A-T) effect when the applied microwave can resonate with adjacent Rydberg states. The MW coupled A-T splitting is proportional to the applied electric field strength, from which the field strength is measured. Using the EIT window, a high sensitivity of 3 μV·cm-1·Hz-1/2 and small electric field of 1 μV/cm are expected to be achieved with a modest setup, and the limitations of the sensitivity are also addressed in the review. For the RF field at frequency mj EIT lines, and avoided crossings formed with the fine-structure levels of equal mj and different J's, which is used to calibrate and measure the RF field amplitude. On the other hand, the dependence of the EIT-line strength on the RF field polarization provides a fast and robust polarization measurement of RF fields based on matching experimental data with a theoretical simulation. The measurements of minimum strengths and sensitivity of RF fields based on Rydberg atoms are one order magnitude below the values obtained by traditional antenna methods. The atom-based field measurement paves the way for determining fields through calibration-free, invariable atomic properties and miniaturization. We also propose its various potential applications in the future.
We present a technique for measuring radio-frequency (RF) electric field strengths with sub-wavelength resolution. We use Rydberg states of rubidium atoms to probe the RF field. The RF field causes an energy splitting of the Rydberg states via the Autler-Townes effect, and we detect the splitting via electromagnetically induced transparency (EIT). We use this technique to measure the electric field distribution inside a glass cylinder with applied RF fields at 17.04 GHz and 104.77 GHz. We achieve a spatial resolution of ≈100 μm, limited by the widths of the laser beams utilized for the EIT spectroscopy. We numerically simulate the fields in the glass cylinder and find good agreement with the measured fields. Our results suggest that this technique could be applied to image fields on a small spatial scale over a large range of frequencies, up into the sub-terahertz regime.